Your computer does not appear on the network

Shared folders, networked computers, flash drives and disks are not displayed in the “Network” tab of Windows Explorer

Hi! For those who are not up to speed, I will start from afar. On computers and laptops with Windows installed, there is a separate “Network” tab in Windows Explorer. This tab shows the devices from the network environment. That is, opening the “Network” tab you can see there computers, NAS, multimedia devices (DLNA), flash drives and external drives that are connected to the router and to which the sharing is configured. Simply put, those devices that are connected via the same router (in the same network) and have network discovery enabled (devices that can be discovered on a local network). Our router (under “Network Infrastructure”) and other devices may also appear there.

I will explain what and how and why I decided to write this article in the first place. I have an Asus router to which I plugged a USB stick, and I set up to share the stick with all the devices on the network. What do you think? The network drive appeared on all of my computers under “Networking” (it just appeared as “Computer”). and it wasn’t showing up on my computer. That is, my computer could not see the flash drive connected to the router or the other computers on the network. But it showed up as a DLNA server running on the same router. But it didn’t make a difference, because I needed normal network access to the drive.

I also couldn’t access it when I typed in //192.168.1.1 in explorer. Right away this address was opened in my browser. And I could not mount it as a network drive. It just wasn’t listed as an available device in the network environment.

It is not uncommon for Windows 7, Windows 8, or Windows 10 not to see network devices. It does not necessarily have to be a flash drive, or an external HDD, which you connected to your router, as in my case. It is most common to set up sharing between computers on a local network. And just as face the problem when the computers are connected to the same network (to the same router). The sharing settings are correct, but the “Network” tab is blank. Or only the router and your computer are shown.

Since the causes and respectively solutions can be many, I will probably start with the simplest (which did not help me) and at the end of this article will share a solution that worked in my case. In the end, my laptop still saw all the devices on the network. Including the network drive and another computer that is also connected to the network.

But this does not mean that this is the case for you. So I advise you to check all the settings in order.

Fix “Network discovery disabled” error in Windows 10 and 11 (updated October 2021.)

We have explained four methods of solving this problem, and all of these solutions apply to both Windows 10 and Windows 11 computers.

Change the advanced sharing settings

First open the Control Panel on your Windows PC. Simply press the Windows key, find “Control Panel” and open it. This step applies to both Windows 10 and Windows 11.

Then open ” Network and Internet ” and go to “Network and Sharing Center”.

To start fixing the “Network discovery disabled” error in Windows 10 and 11, click ” Change advanced sharing settings ” in the left pane.

Here, in the “Personal” section, make sure that the option ” Enable network discovery ” is enabled. Also check the box “Enable automatic configuration of devices connected to the network”.

Then under “File and printer sharing” enable ” Enable file and printer sharing.

Similarly expand the “Guest or Sharing” section and enable “Enable network discovery” and “Enable File and Printer Sharing. As a general rule, I don’t recommend enabling network discovery on a public network. But if you’re working with public Wi-Fi, leave it on for now and don’t forget to turn it off after your work is done. Finally, click “Save Changes.”.

Now restart your computer and see if the “Network discovery disabled” error is fixed.

Manage Windows services

If the above method did not fix the network detection problem on your Windows 10 or 11 computer, follow these steps to get a more viable solution.1. Press the Windows shortcut “Win R” to open the “Run” window. Type services.Type msc and hit Enter.

Scroll down and find “Publish Function Discovery Resources”. Double-click on it and change “Startup Type” to “Automatic”. After that, click “Start” under “Service Status” and click “OK”.

Then find the “DNS Client” service and make sure it is also set to “Automatic”. Also make sure the service is running.

Finally, find “SSDP Discovery” and open it. Change it to “Automatic” in the drop-down menu and start the service.

See also  How to choose a power bank for your phone

Now reboot your computer to fix the problem and check if the “Network Discovery Disabled” issue is resolved on your Windows 10/11 computer.

Configure the firewall settings

Press the Windows key and search for “Windows Firewall” on your Windows 10 or 11 computer. Now open the “Windows Defender Firewall” settings in Control Panel.

On the left pane, click “Allow application or feature through Windows Defender Firewall”.

Then click “Change Settings” in the upper right corner and look for “Network Discovery. Make sure the feature is enabled and “Private” and “Public” are checked.

your, computer, does, appear, network

Finally, click “OK” and this should solve the “Network discovery disabled” problem on your Windows 10/11 PC.

Reset the network

If none of the above methods have fixed the problem, you may need to reboot the network on your Windows 10/11 PC. To do this, follow these steps:1. Press the Windows key, search for “Reset Network” and open it on your Windows 10 PC. In Windows 11, open “Settings” and go to “Network and Internet”. “Advanced network settings.”. “Reset network.”.

Then click “Reset Now” and that’s it. Reboot the computer and the problem with the network discovery disconnection should disappear.

You can also follow our guide on how to fix network connectivity issues in Windows 10/11 for a detailed step-by-step process.

Causes and solutions to “invisibility

A few words about your router and antivirus

For starters, I would suggest going into your router settings and seeing if all enabled computers show up in it (you can usually do this under the “Bandwidth Control” tab ).

Make sure that the router does not block your PC, you must not set any limitations. All computers connected to the router must have an IP address of the form: 192.168.0.100, 192.168.0.101, 192.168.0.102 and t.д. ( note: not exactly the same, but a similar sequence of. )

Are the two devices connected to the router

Next, open the network adapter settings for your notebook (PC) by pressing WinR to open the “Run” window. and use the command ncpa.cpl.

ncpa.cpl. view all network connections

Next, open the properties of the adapter, which provides the connection (on notebooks it is often wireless, on PCs. Ethernet).

Then they go to the properties of IP version 4 (see. screenshot below) and set it to obtain IP address automatically. As a DNS I would recommend to set 8.8.8.8 и 8.8.4.4 (this is Google DNS, they are faster and more stable than your ISP).

To help!

How to change DNS in Windows, and how to choose the fastest public DNS server. https://ocomp.info/kak-vyibrat-public-dns.html

If you have an anti-virus (e.g. Kaspersky) do not forget to disable any virtual network connection. In general it is advisable to stop operation of antivirus for the period of adjustment and diagnostics.

PC name and workgroup name

You must have the same workgroup and different names for the computers on the local network to see each other.

To check these settings. open explorer (WinE combination), go to the “This computer” tab and open its properties. See. screenshot below.

Of course you must check the workgroup on each PC in your local network (it must be the same on all computers). For home use the default value. WORKGROUP).

If you need to change a workgroup or computer name. Do not forget to reboot your device.

Is network discovery enabled

By default, this feature is disabled on Windows 10/11 for security reasons ! To enable it, you need to open Control Panel and go to “Network and Internet” section. After opening the “Network and Sharing Center” tab.

Then in the menu on the left to open the additional. Sharing options.

Then expand all three profiles one by one (private, guest and all networks) and:

Turn on sharing and deactivate password protection

Note: after changing these settings, you must reboot the computer.

The SMB protocol is necessary for the Computer Browser service, which inventories computers on the network and displays them. But in Windows 10 (1709 and above) SMB is disabled by default (for security reasons).

So, to solve the invisibility of the network environment. you need to check whether you have it enabled and, if necessary, activate. This is done quite simply: first, you should open the control panel and go to “Programs / Programs and Features”.

Next, in the menu on the left, open the link “Enable and disable Windows components”.

Find the “SMB File Sharing Support” tab and check the checkboxes next to client and server. Save the settings (after Windows will find and install it). An example in the screenshot below.

Does “Function Discovery Resource Publication” work?

In Windows 10 (1803) the Function Discovery Resource Publication service has been changed. “Publish function discovery resources”). by default it does not start now. If this service doesn’t work. your computer will be invisible to other PC’s on local network.

your, computer, does, appear, network

Reasons and solutions for “invisibility

A few words about the router and antivirus

First, I would suggest you go to your router’s settings and see if all enabled computers are shown in the router (usually you can do this under the “Bandwidth Control” tab).

Pay attention to the fact that the router does not block the work of your PC, there are no restrictions. All computers connected to the router must have an IP address of the form: 192.168.0.100, 192.168.0.101, 192.168.0.102 and t.д. ( note : not exactly the same, but a similar sequence)

See also  How to make a network between two computers

To help! How to enter the router settings. https://ocomp.info/kak-zayti-v-nastroyki-routera.html

Are these two devices connected to the router?

Next, open the network adapter settings of your laptop (computer): To do this, press WinR to bring up the “Run” window, and use the command ncpa.cpl.

ncpa.cpl. Display all network connections

Then you have to open the properties of the adapter which establishes the connection (on notebooks it is usually wireless, on PC it is Ethernet).

Then go to the properties of IP version 4 (see. screenshot below) and set the settings to obtain an IP address automatically. As a DNS I would recommend to use 8.8.8.8 и 8.8.4.4 (this is Google DNS, it is faster and more stable than your provider).

If you have an anti-virus (for example Kaspersky) do not forget to disable any virtual network connection In general it is desirable to suspend the anti-virus completely for the period of adjustment and diagnosis.

PC name and workgroup name

For computers on your local network to see each other they must have the same workgroup and different names. To find out about these settings. open Windows Explorer (WinE), go to “This computer” tab and open its properties. See. screenshot below.

Of course, you must check the workgroup on each PC on the local network (it must be the same on all. At home, the default value is usually WORKGROUP.).

If you need to change workgroup or computer name do not forget to reboot the device afterwards.

Is network discovery enabled

By default, this feature is turned off in Windows 10 for security reasons ! To disable it, open the control panel and go to “Network and Internet” section. Then open the “Network and Sharing Center” tab.

Then in the menu on the left to open additional. Sharing settings.

Then expand all three profiles one by one (private, guest and all networks) and:

Turn on public access and disable password protection

Note: You have to reboot computer after changing these settings.

The SMB protocol is necessary for the Computer Browser service, which compiles the list of network computers and is responsible for displaying them. But in Windows 10 (1709 and above) the SMB protocol is disabled by default (for security reasons).

So, to solve the invisibility of the network environment. you need to check whether you have it enabled and if necessary to activate. This is done quite simply: first, you must open the control panel and go to the tab “Programs / Programs and Features”.

Next, in the menu on the left, open the link “Enable and disable Windows components”.

Find the “SMB file sharing support” tab and check the boxes for client and server. Save settings (after Windows finds and installs everything). An example in the screenshot below.

Does “Function Discovery Resource Publication” / “Function Discovery Resource Publication” work

In Windows 10 (1803) the Function Discovery Resource Publication service has been changed (in Russian. “Publish function discovery resources”). by default it does not start now. If this service is not running. then your computer will not be visible to other PC’s on the local network.

To fix this, you need to open the tab in Windows services. To do this, press WinR. And enter the services command.msc. Example below.

Open services. services.msc (universal way)

In the list of services, find “Publish feature detection resources” and change its startup type to “Automatic”. Next, save the configuration and restart your computer.

And if the folder/drive is shared.

And the final touchIs your folder on your notebook (PC) shared and invisible to others?? To see what you have open for sharing: go into explorer (WinE), expand the “Network” tab. and click on your computer name. If you have anything shared, you should see these folders.

To share a folder or a drive: click on it with the left mouse button and then click on “Grant access / Single people.

Next, select the users (usually “All”. t.е. so that the folder can be accessed by all users on the local network) and give them the option to access it:

Workgroup

WARNING! In the new updates, Microsoft has removed the ability to configure a workgroup. skip this chapter.

You also need to go into your system options. To do this, right-click on “Computer” and select “Properties”, or press “Win” and the “Pause” key at the same time. Go to advanced settings and under the tab “Computer name” click on “Identification”.

  • Choose corporate network.
  • Using a network without a domain.
  • On both computers you need to specify the same workgroup, by default this is “WORKGROUP”.

After that, restart both computers and then check the network.

Hide the computer in a network environment

You may need to remove the display of the computer in the network environment. So that the access to the local network remains, but the computer is not visible in this menu. This may be needed for different purposes, but is mostly used to restrict external users who for one reason or another occasionally have access to a device. The method is valid on Windows server 2003:

After that in a network environment your computer will not see other devices, although the local connection between them will remain.

The network environment is used for the convenience of users and allows you to manage the local networks you have created. So it’s important to know not only where it is, but also how to solve any problems related to it. Then your connection to the other device will work the way you need it to.

See also  How to open a zip file on Android. Zarchiver

How to enable network discovery in Windows 10?

Starting with Windows 10 1803 (Spring Creators Update), Microsoft developers have removed the ability to create a homegroup. Also, Windows 10 computers no longer show up in the network explorer environment when you view network devices.

From Microsoft’s point of view, a homegroup. Is an outdated way to create a local network to share folders and printers. Instead of using a home group, Microsoft suggests using its cloud services (OneDrive or access through Microsoft accounts).

In Windows 10 1803 (and newer), in order to access shared resources on another computer over the local network, you need to know its hostname (\IMJ-PC1) or IP address (\192.168.1.90), but neighboring computers on the network are not displayed. However, this can be fixed.

You can create desktop shortcuts to neighboring computers by specifying the UNC path to them (by computer name or IP address).

The point is that a separate Function Discovery Provider Host service is responsible for discovering neighboring computers on your Windows 10 network. Another service, Function Discovery Resource Publication, is responsible for discovering your computer.

The FdPHost service uses Simple Services Discovery Protocol (SSDP) and Web Services Discovery (WS-Discovery) to discover devices on the network.

These protocols replace NetBIOS over TCP/IP which was historically used to discover devices on Microsoft Windows networks by using the Master Browser. Accordingly, you can safely disable NetBIOS protocol for your network adapters.

After installing the latest Windows 10 builds, you can disable these services (the startup type changes from Automatic to Disabled). If these services are stopped, the computer is not detected on the network by other computers and cannot see other. You can enable network discovery services in Windows 10 as follows.

  • Open the Windows Services management console (services.msc);
  • In the list of services, find the Function Discovery Resource Publication service;
  • Change the service startup type from manual to automatic (delayed start);
  • In the same way, enable the Function Discovery Provider Host service; You can change the start type of these services by using the following one-line PowerShell command:
  • Reboot your computer

After rebooting, other computers on your local network will be able to detect that computer and its resources (shared network printers and folders).

Workgroup settings

In order to check that the computer is not really visible in the local network, you can expand the “Network” list in Explorer or enter the command “net view” in the “Run” window (opened by pressing Win R at the same time). If the required PC is not on the list or the inquiry receives a message that there are no items, this may be due to incorrect workgroup settings.

The problem is solved by performing the following actions

  • Open the system properties.
  • Find the tab called “Computer Name”.
  • Click on “Identity”.
  • After launching the setup wizard, one at a time, specify that the PC is part of the corporate network, the organization does not use domains, and the workgroup name is WORKGROUP.

After that you should reboot the system and make sure that “private” is indicated in the network type settings. The name WORKGROUP can be changed. but it’s better not to, as the name is often the default. And preferably it must be the same on all computers in the network.

How to configure TCP/IP settings

If the problem is not with the driver, you should check the main program settings which affect your Internet connection. Check if the required protocols are activated and if obtaining an IP address and DNS is working.

Check for activated network protocols

The underlying IPv4 protocol must be activated for the Internet to work properly. Additionally it is worth trying to disable or enable IPv6. in some situations it may cause unpredictable behavior.

Checking IP and DNS resolution settings

If deactivating or activating the protocols does not help, you should check your IP and DNS settings.

  • Press Win R. Type the ncpa command.Press the Enter key and then press the Enter key.
  • Find the network adapter you are looking for, right-click on it and select Properties.
  • Click on IP version 4 (TCP/IPv4) and click on Properties.

If this does not solve the problem, you should try changing the DNS addresses to those provided by Google. This often works.

  • Tick the Use the following DNS servers checkbox.
  • Enter the digits 8 in the Preferred DNS server field.8.8.8.
  • Enter in the Alternative DNS-server field the numbers 8.8.4.4.

After doing all of these things, you might want to reboot the computer to see if they help.

Configure the FIPS standard

Sometimes enabling or disabling FIPS (Federal Information Processing Standards) may help. It was created for U.S. government agencies, but is available to computers in any region.

Denial of responsibility | Contacts |RSS | SE | EN | BR | DE