xiaomi redmi 4x how to set up

Table of Contents

To reset your Xiaomi Redmi 4X smartphone, follow these steps:

  • Download the file to your computer from the link https://drive.google.com/file/d/1Im8pBtgYYzVDqBZ6FGk66Y9pJRhmlEWt/view
  • Run it and in the center of the window that appears, click on the only button.
  • Wait for the program to load.
  • In the window of this program, click on the button in the lower right corner.
  • Click on the Recovery button. This completes the actions with the computer for now.
  • Take the phone, turn it off and after, hold down the Power and Volume buttons together
  • Hold this combination until the screen lights up, then release the Power button, and continue to hold the Volume.
  • Tap on the Recovery button on your phone.
  • Touch the blue button.
  • Wait for the picture with the drawn wire to appear on the phone screen.
  • Connect your phone to your computer with a cable.
  • After 5-10 seconds on the computer screen in the new program window that appears, select the third button from the top.
  • Select left button (reset confirmation).
  • We wait until the picture with the image of the wire appears on the smartphone screen again and disconnect the phone from the computer.
  • Hold down the Power button on your phone for 5 seconds.
  • Redmi 4x will boot for the first time.
  • The program on the computer can be closed. Hard reset done.

Device router Xiaomi Redmi Router AC2100

The Redmi AC2100 router has a number of ports, buttons and indicators. On the rear panel there is a connector for connecting the device to a power outlet and four ports. The port on the far left is labeled Internet and is intended for connecting the provider’s cable. Three other ports are marked with dots from one to three and are needed to connect devices that will access the Internet from the router. You will also connect a computer to any of these ports, with which you can manage the router through the administrator panel. Also on this side you will find the Reset button, which will help you restore the router to factory settings in case of failure or loss of the password to the admin panel. To reset the settings, you need to hold the button for 5 seconds.

There are two indicators on the front panel of the router. Each of them works in several modes. The System LED glows orange and blue. When the router is turned on, the system starts up, which is accompanied by a constant orange glow of the indicator. When the router is ready for use, the orange glow will change to a solid blue. If the router starts updating, it will flash orange until the update process is complete. But the constant red light of this indicator warns you that the system has failed. No indication means the router is not receiving power.
The Internet indicator also glows orange or blue. A constant blue glow will tell you that everything is in order with the Internet, a blinking blue indicates a data update. And the orange glow warns that there is no access to the Internet. If the indicator does not light up at all, it means that the network cable is not connected. In addition, the Xiaomi Redmi Router AC2100 model has lugs for hanging the device on the wall, six antennas and a sticker with information for setting up the router. The box itself comes with a power adapter and a network cable. Since this model comes with a flat-prong power adapter, you may need an adapter.

Additional settings of the Wi-Fi router Redmi Router AC2100

The settings described above are enough for you to have Internet in your house. However, consideration of the remaining capabilities of the router may be useful to you for solving some practical problems. Let’s look at some of them. There are three main sections in the admin panel: “Status” (Status), “Settings” (Setting), and “Advanced” In the status section and on the devices tab, you can view a list of all connected to 2.4 GHz networks and 5 GHz devices and manage them. For example, if you see an unfamiliar name in the list or want to deprive your child of the Internet, just turn off his device. In the Internet section, you will see the bandwidth of your mowing line. In the settings section, there are five tabs that are responsible for setting up wireless networks, Internet, security, local network and status. If you need to change the network name and password for it (someone connects to the router without your consent), use the already familiar Wi-Fi settings tab. Here you may need the ability to create black and white lists, adjust the Internet speed and more. Finally, advanced settings are for advanced users. Among all the settings, we also pay attention to the possibility of updating the firmware, which can be resorted to if the router is unstable, if you want to expand its functionality or change the language.

How to set up Xiaomi Redmi Router AC2100 router

Now come up with and enter in the Network field a name for your wireless network, and in the Password field, come up with and set a password for it. Be sure to write down this information in a notebook, as they do not have to be used often, and over time they are forgotten. If you want the signal to pass through the walls of your house, check the box Turn on wall penetration mode. Click the Next button. Also, the router can request data from your provider or detect them automatically. In the first case, enter a name and password or other requested data, which you can look at the provider’s documentation or ask him for a hot mowing line If you want to leave it, then check the Same as Wi-Fi password field, otherwise delete the data from the Password field and enter a new password. Also write down this password, otherwise if you lose it, you will have to reset the router settings to factory settings. Click Set up successfully which will complete the setup. Next, click on the Router admin page line to go to the admin panel. Open the Settings section and find the Wi-Fi settings tab in it. If you activate the Dual-band Wi-Fi option, then your 2.4 GHz and 5 GHz networks will be combined into one with a common name. In this case, the router will independently switch from one network to another, depending on the capabilities of the connected devices or network bandwidth. Select the type of encryption for the network or networks in the Encruption line: it is recommended to set it to Strong (WPA2-personal). Click the Save button. Your router setup is complete.

Instructions for connecting and configuring the Xiaomi Redmi Router AC2100 router

The Xiaomi Redmi Router AC2100 router is not difficult to set up, but if you have no experience with routers, a short instruction may not help you. Therefore, we have prepared a detailed article in which we will explain the purpose of all the elements of this model, we will deal with the ways to connect the router and the settings that are maintained in a foreign language.

How to connect Xiaomi Redmi Router AC2100 router

Before setting up the router, it must be connected to the Internet and to a computer or smartphone for data entry. Let’s deal with the first question. To get started, connect the power adapter to the router, turn on the device and wait for it to boot. If a provider cable comes into your house, then do the following. Connect your ISP cable to the port labeled Internet. If connecting via a modem, take a network cable from the modem or router box, insert it with one end into the Internet port of the router, and the other end into the modem’s network port. Connect the modem to the appropriate mowing line (for example, to a telephone line) and turn it on. After connecting to the Internet and loading, the router will start broadcasting its own Wi-Fi network. Now you can connect to this network from a laptop, tablet, smartphone and other device with a Wi-Fi module that can open the admin panel or run a mobile application. To do this, build a list of available wireless networks and find your router’s network called Redmi_XXXX in it. The exact name is indicated on the label of the router in the lines “2.4G Wi-Fi” and “5G Wi-Fi”. By default, the network password is not set. You can also connect to the router from a computer via a cable. To do this, take a network cable from the router box and insert it with one end into any LAN port (indicated by dots), with the other end into the computer’s network port. Now you can start the settings.

Connecting Home Devices to Redmi Router AC2100

If you did everything correctly, now your router should distribute the Internet. It remains only to connect other devices to it using cables or via Wi-Fi. For a wired connection, prepare a cable of the required length, connect it with one side to a free LAN port of the router (indicated by dots), and the other side to the network port of the device (TV, set-top box, etc.). Go to the device menu, find the network connections section there, select the wired option and set the requested parameters. For a wireless connection, activate the Wi-Fi module on the device, start searching for available wireless networks, find your new network in the built list and connect to it. Do not forget that during the settings you set a new name for the network and came up with a password for it. Now it is these data that you need to enter when connecting. Starting a network search on different devices is different. For example, on a phone, you can do this by long-clicking on the Wi-Fi icon, pressing the “Search for networks” button, or selecting a similar function. On a computer with a Wi-Fi adapter, you need to find the “Network”, “Wi-Fi”, “Wireless Connections” section or a similar section. When the Wi-Fi adapter is enabled, the list of networks will be built automatically. The above information should be enough for you to basic configure the Xiaomi Redmi Router AC2100 router and provide all home devices with the Internet. You can also figure out some of the settings yourself without resorting to learning special terminology. It can be scheduling, signal strength selection and more. If the Internet disappears after your settings, just press the Reset button for five seconds and start the setup again, as described above.

Quick and complete backup of Xiaomi Redmi 4X and Redmi 4 Prime: how to do it [archive]

This post will briefly talk about how to quickly backup Xiaomi Redmi 4X and Prime. The two most simple methods are described below: backup using the standard MIUI function and backup using the function of the popular TWRP Custom Recovery utility.

So, how to quickly back up data on Xiaomi Redmi 4X and Redmi 4 Prime smartphones.

backup Xiaomi Redmi 4 using the proprietary software tool MIUI Stock Recovery

The MIUI Stock Recovery utility allows you to backup and restore applications, accounts, contacts, and various files. However, it should be borne in mind that MIUI Stock Recovery cannot back up the installed firmware and IMEI code of the smartphone.

Before starting the backup procedure on Xiaomi, you must specify the location where the backup files will be saved.

So tap on Settings. Memory. Settings. Backup data and then select either the built-in memory of the smartphone (if its volume is sufficient), or the SD card (if any). The manufacturer recommends backing up data to an external drive.

After that, click Settings. Advanced (in the System and device section). Restore and reset. Local backup, mark the data that needs to be saved, and tap Start.

Backup copies of data will be created and saved in a separate folder at MIUI/backup/AllBackup.

In the future, to restore data from saved copies, simply click Settings again. Additionally. Recovery and reset. Local backup, select the desired archive and tap Restore.

backup Xiaomi Redmi 4 using TWRP Custom Recovery utility

The main advantage of this method is that in TWRP Custom Recovery you can create a complete backup of the entire smartphone system, including user personal data and system partitions (IMEI, modem, Download, Restore).

At the preparation stage, it is recommended to clear the Cache and Dalvik Cache. To do this, we reboot into TWRP, tap the Wipe button, select the Cache, Dalvik Cache sections (tick) and swipe the blue button at the bottom.

Then we return to the main TWRP menu, tap the Backup button, go to the Select storage tab and specify the system partition in which the backup data will be saved.

Now in the menu we select the partition that needs to be backed up (you can select all partitions if you need to create a full backup of Xiaomi Redmi 4) and run the procedure.

After it is completed, backup copies of data will be saved at / TWRP / BACKUPS /.

Next, to restore data from backups, we reboot in TWRP Custom Recovery mode, click Restore in the menu, find the backup, select the partition to be restored and swipe on the blue button at the bottom of the screen to launch the recovery process.

Housing material and fastening principle

The body of the Xiaomi Redmi 4X smartphone is made very simply. There is a board, on the one hand, a display is fixed on it, and on the other, various components. These include processor, mini-boards, camera modules, battery, etc.

The back panel of the phone case is made mainly from a single piece of aluminum (only narrow plastic inserts at the bottom and top). There is a fingerprint scanner on the back cover. This cover is attached with special latches to the part where the display and all components are placed. Such latches can be easily “unfastened” with a special plastic spatula.

Instructions for disassembling Xiaomi Redmi 4X

Situations when it is necessary to disassemble Xiaomi Redmi 4X are rare. This mainly happens when you need to replace a broken display or camera module. The internal components of the devices last more than 10 years, as the manufacturer purchases parts only from the largest companies. Therefore, few people know that the smartphones of the Chinese brand are very easy to disassemble, and there is absolutely no need to contact a service center. This article will show you how to do it.

See also  xiaomi redmi note 9 warming up

Procedure

Before disassembling the device, you need to remove the SIM card and flash drive from the smartphone.

Be sure to do this otherwise you will damage the connectors in the process of removing the rear panel. Next, you will need to use the tools to proceed with the following steps:

  • A special plastic spatula must be slipped under the back panel of the phone from the side of the screen and threaded through it by about 1-2 millimeters. Next, hold it around the entire perimeter of the phone. This will open the latches.
  • When the latches are open, you need to very slowly remove the cover, which is the entire back panel. At the same time, to begin with, it only needs to be slightly lifted.

Attention: you need to be extremely careful! Since there is a fingerprint scanner cable from one part of the smartphone to another! The length of this cable is minimal, so you can not sharply turn both parts of the smartphone.

Next, you need to remove the fingerprint scanner cable. To do this, carefully pry off the cable mount and pull it out (there may be an adhesive tape that must first be peeled off and lifted). The train will then easily give in.

  • After that, the chipset will open up. A protective board will be installed on top of it. The battery is also located here. The camera module is located above the chipset. It is removed simply: to disconnect, pull out the cable, as is the case with the fingerprint scanner. To remove the processor or disconnect the battery, you will need to use a Phillips screwdriver (1.5 mm) to remove all screws. At the same stage, it is possible to remove the section on which the speaker is located.
  • After all the screws are unscrewed, the phone is considered completely disassembled. It remains only to pull out all the components one by one.

Important: there may be other cables under different modules, so if something will not be removed, then you need to disconnect the cables from the connectors.

It should be noted that the size of the screws is not the same. The ones on top are longer. This must not be forgotten during the assembly process.

  • After removing the protective board, the battery mounts will become visible. They need to be pulled out. Not the fact that the battery will immediately succumb. If moderate pressure isn’t enough, you’ll need to heat up the case a bit to soften the adhesive and peel the battery off the panel.

Thus, removing the back panel and all internal components from Xiaomi is quite simple. The main thing is to be careful in disassembling, control all actions and their effort, and also do not forget to remove the fasteners of the cables from the connectors.

Xiaomi itself is assembled in the reverse order, the back cover will easily snap into place in its mounts with a characteristic click.

How to Enable or Disable Dual Clock Feature on Xiaomi Phone Screen

In the new versions of MIUI (latest updates version 10, 11 and 12), Xiaomi phones have an interesting dual clock feature. It adds a special widget to the screen that shows the time in different regions. Let’s figure out how to enable and configure this feature, as well as how to disable it and remove the widget from the screen.

What versions of MIUI does it work in and what does it look like

The dual clock works in the latest global updates, starting from MIUI 10. Earlier versions of MIUI also have a function, but the display shows one widget divided into two parts, as already mentioned above.

The working screen after turning on and configuring will look like this:

Power on and setup

To enable dual time, follow our step-by-step guide:

  • Open the Clock application, you can do this either through the icon of the same name in the menu, or by clicking on the time on the desktop.
  • Click on “Three dots” in the upper right corner and select “Settings”.

To change the look of the clock, you need to change the theme of your smartphone through the Themes application, and the appearance of the widget will change with it. The developers claim that for the option to work correctly, a default theme and a stock lock screen are required. However, some of the installed themes support such a widget, you just need to try to install it and restart your smartphone.

What is this function

Dual clock on Xiaomi is a MIUI skinned widget that shows the time in different regions of the country. This widget can be configured to display both on the main screen of the smartphone and on the lock screen.

Previously, this option supported only one widget, but now a separate watch face will be installed for each region.

Thus, thanks to this functionality, the user gets the opportunity to set the local time and the time of another desired region that needs to be monitored. This solution is perfect for travelers to track the time in their hometown and in the region where they are located.

If the clock does not appear, in the “Settings” open the “Date and time” section and turn on the “Automatic detection” of the time zone, or manually specify the region in which you are currently located. Then open the “Clock” application and in the parameters mark the second region in which you want to track the time.

If the screen displays the wrong time, try turning on the Internet, geolocation and automatic time zone detection. Or vice versa, turn off automatic detection and specify the city manually.

Thus, the “Dual Clock” feature introduced in recent MIUI updates will be useful for a lot of users. It can make life easier for travelers or those who constantly move from one city to another. You can also use it to track the time in the region where, for example, relatives or friends live.

So, first we connect the phone to the computer, remove the lock mode and open the option Settings → About phone (see screenshot) → click several times on the MIUI Version tab until you see the inscription below No need, you are already a developer (see screenshot). Next, open Settings → Advanced (see.

We take a paper clip and insert it with a sharp end strictly perpendicularly into the hole, which is located below the tray itself, after a click, the tray will pop out of the smartphone case and can be pulled out freely. This smartphone supports two types of SIM card placement: micro SIM card nano SIM card

How to increase or decrease the volume on Xiaomi Redmi 4X

One of the main characteristics of your Xiaomi Redmi 4X. it’s the sound it makes. This is a very important feature when you are calling someone, listening to music or watching a movie. You also have the option to adjust the volume as you wish, by increasing or decreasing it. Therefore, sound is important for your device. In this article, we will first explain to you how to increase or decrease the volume using the volume buttons on your Xiaomi Redmi 4X, then using the settings menu, and finally using third-party applications.

Increase and decrease the volume of your Xiaomi Redmi 4X with the volume buttons

Surely you noticed this when buying Xiaomi Redmi 4X, but you have two similar buttons on the side of the device, one at the top and the other at the bottom.

These two buttons are for volume up and down. The top volume knob is used to increase the volume when using Xiaomi Redmi 4X sound. On some devices, they tell you when the sound gets loud and could be harmful to your ears.

As for the bottom button, it is used to decrease the sound until the sound stops coming out of your Xiaomi Redmi 4X. These buttons can be used both when using speakers and headphones.

Increase and decrease the sound of your Xiaomi Redmi 4X through the “Sound” options menu.

There is another way to increase or decrease the volume of your Xiaomi Redmi 4X. First, go to your device settings, then click “Sounds” where all the sounds of your Xiaomi Redmi 4X will be listed. Then click “Quality and Sound Effects”, “Sound Settings”, or “Sound Settings”. In these settings you will find all sorts of settings to customize the sound to your liking.

During these settings, you can listen to the sound of your Xiaomi Redmi 4X to evaluate whether your settings are correct or not.

Turn up and down the sound of your Xiaomi Redmi 4X with third-party apps

Thanks to the Google Play Store, you can find a wide range of applications to increase or decrease the sound of your Xiaomi Redmi 4X. To do this, type “Increase phone volume” or vice versa “Decrease phone volume”. If you want to maintain good audio quality, we highly recommend that you do two separate searches to get two apps that fully meet your expectations.

Warning ! Some applications are free and others are paid, please read the information about them carefully. We also advise you to carefully read the ratings and user reviews in order to choose the most suitable application for you.

your Xiaomi Redmi 4X. practical and powerful tool for sound.

To be able to call and hear the interlocutor correctly, listen carefully to music or movies on your Xiaomi Redmi 4X, hear the noise of your phone when it is in call mode, etc. Therefore, the sound is necessary in the phone, some even want to use it.

After you give some tips to turn the volume up and down on your Xiaomi Redmi 4X, we will give you two very simple tips on the same topic. First, check where your device’s speakers are located so as not to obstruct the sound output through them.

Secondly, put the Xiaomi Redmi 4X speakers in an empty glass and you will be amazed by the sound your device makes. In case of difficulty, do not hesitate to contact a specialist who can help you with any difficulties you encounter. We hope to have helped you understand the scope of the smartphone and its jailbreak as best as possible.

Create an account and email

If you do not have a ready-made Google profile and Mi Account, you will be prompted to register during the initial setup. The login procedure ends with confirmation by SMS. It is inconvenient to use the phone without being linked to accounts, some of the features will not be available, so it is recommended not to skip the stage. How to do this is described in detail here.

It is more convenient to set up mail from a PC, but the principle is almost the same for mobile devices.

  • Visit accounts.google.com/SignUp?hl=en
  • Enter your first and last name in the fields, create a username for email and a password. Click “Next”.
  • You will be prompted to add a phone number, enter it as well. Google will send an SMS with a code that you need to enter on the page in the browser.

The same actions are performed from a mobile gadget. Open the link in a browser or find the “Synchronization” item in the settings and then “Add an account”. On the page that opens, click “Create”.

You can do without a Google entry, but Xiaomi smartphones do not work without being linked to a Mi Account.

  • Open the link in any browser: account.Xiaomi.com/pass/register.
  • Enter your email. Country is selected automatically.
  • Create and enter a password twice, solve the captcha and click Submit.
  • It is worth linking a phone number to this account as well, then the range of functions will expand. For example, remote gadget search will become available.
  • Confirm registration by entering the code from SMS or email.

Further management takes place on the Mi Account tab in the menu. System programs that work with Mi Recording require access to contacts and media on first launch.

Attention! Note that the gadget is linked to the entry. Before selling or transferring to another user, the account on the smartphone must be deleted.

Setting up the Internet

It is proposed to connect to a home Wi-Fi router even when you first start the Xiaomi device. If you didn’t do it right away, here’s a step-by-step guide:

  • open the notification shade;
  • click on the Wi-Fi icon and hold your finger for a few seconds until the menu opens;
  • choose your SSID, connect.

Sometimes you need to manually update the list of networks, this is done using the button at the bottom of the screen.

Mobile Internet management is as follows:

  • Open the settings sub-item “SIM cards and mobile networks”.
  • Data transfer is enabled by switching the slider “Mobile Internet”.
  • In the “Default Settings” submenu, you can set one of the two SIM cards for accessing the network. The alternative is to always ask which SIM card to access.
  • The “Traffic Settings” option is used to control the use of megabytes. Here you can specify the total amount for the month and the spending limit.
  • Clicking on the name of the SIM card at the very top of the menu will open a sub-item where you can change the name of the card, select the preferred network type (from 2G to 4G) and activate the hotspot. Information provided by the operator.

For manual settings, see this article.

Overview of Xiaomi Redmi 4X smartphone settings

Xiaomi gadgets have a reputation for high-performance devices with excellent value for money. There are more and more buyers who have overcome the outdated stereotype about the low quality of Chinese technology every year. The Redmi series belongs to the budget price segment, including the Xiaomi Redmi 4X smartphone, the settings of which are voluminous, contain many options, the purpose of which is unclear to a beginner. To comfortably use the technique, you need to debug it and “adjust” it to your needs. And how to do this, we will consider in the article.

Primary settings

After purchase, the device is in the “factory” state, all options are set by default. During the first run, the user will be asked to set values ​​for several parameters:

  • shell language;
  • connection to a wireless network, if available;
  • signing in and linking a Google account;
  • connection with Mi Account.

The above points are enough to get started with the gadget. An advanced user can go further and customize the device entirely for themselves.

Appearance

Desktop customization allows you to change the theme to a more pleasant one. There are four preset pictures to choose from, but a catalog of hundreds of options is available for download.

  • On the main screen, find the “Tools” folder, and then the “Themes” item. The Mi Themes utility will open. Here you can download individual wallpapers or ready-made designs. There is a search with a filter and a preview mode. Everything is free. Icons, curtain and screensaver change at the same time, as well as images for the desktop and lock screen.
  • Make a pinch gesture with two fingers on the home screen. Three buttons will appear at the bottom. “Wallpaper”, “Widgets” and “Settings”. The first item allows you to set any picture from the device’s memory to the screen. From the second tab, you can drag widgets onto the table, their variety depends on the installed applications. The last item is used to configure some options, including protection against changes and screen transition effects.

The sound design is also configurable, but already on the “Sound and vibration” tab.

However, to enter here you will need to go to the usual phone settings by sliding the top curtain down and clicking on the gear icon in the upper right corner.

The main menu opens by clicking on the gear on the right in the notification shade. Available options:

  • ringtone;
  • notification of SMS, calendar event or new notification;
  • alarm melody;
  • turning on and selecting the vibration level for each item;
  • vibration response to any action;
  • sounds for dialing, locking the display, taking a screenshot, and tapping the screen.

The sound volume level is set by simply pressing the Volume Up and Volume Down rockers.

The choice of language affects the operation of the voice assistant and the Google speech synthesizer. The gadget will speak with the owner in Russian, and understand only the corresponding speech.

The COMPASS needs to be calibrated for normal operation of the cards. Go to the “Tools” folder, find the shortcut “COMPASS” and run.

See also  Bottom buttons not working on Xiaomi

Rotate the device in the air, circling the “eight” with your hand several times. The accelerometer will measure the change in position along three axes. The phone will vibrate and give a “Calibration completed” notification. The procedure should be repeated periodically.

Setting the time and date

For new phones, you do not need to manually set these values. Date and time are automatically requested from the telecom operator.

If you wish, you can set the time yourself on the “Date and Time” tab of the same name, which is hidden in the “Advanced Settings” submenu.

Here you can also set the time zone settings and the display format (12- or 24-hour).

Alarm options are located separately. To access them on the home screen, tap on the clock widget. If you click on the time, the alarm will open. If you hit a date with your finger. a calendar.

In addition to the alarm clock, the menu contains a world clock, a stopwatch and a timer. Clicking on the three vertical dots in the top right corner will open options. Here you can set the melody, volume, repeat interval of the signal. An interesting feature. on the birthday of the owner, the smartphone will perform the song Happy Birthday, if you check the corresponding box.

Camera optimization

By default, the manufacturer has set non-optimal settings for the phone’s camera. It should be fixed.

Open the camera with a shortcut from the desktop and tap “Modes”. In the upper right corner is a white gear, click.

  • Activate the “Save to SD card” checkbox so as not to fill up the limited internal memory.
  • “mowing line of the net”. so as not to fill up the horizon when shooting.
  • “Photo quality” set to “High”.
  • The frame format does not need to be changed, like the rest of the options. Exposure mode is better to choose “Center-weighted”.

Switch to video mode and open the menu using the method described above. To improve video quality on Xiaomi:

  • “Focus mode” set to continuous.
  • “Recording quality” select the maximum. Full. There are tweaks that unlock 4K resolution. At the same time, the performance drops sharply, since the device is not designed for shooting in this mode.

Read about more advanced settings here.

A feature of most Xiaomi smartphones is the presence of a fingerprint scanner. Using the sensor allows you to unlock the device without entering a password.

Proceed to the “Lock and protect” submenu, where click “Manage fingerprints”. You must first set a password, PIN or pattern.

A window will open where the user can delete and add fingerprints.

You can add a snapshot of a finger by pressing the corresponding button. You will be prompted to apply the pad of your finger at different angles several times.

A detailed description of how to work with the scanner can be found here.

There is nothing complicated in setting up the device to suit your needs. All Xiaomi menus are very similar, since a single MIUI shell is used. If you did something wrong, restore the factory settings in the “Restore and reset” submenu. Everything will revert back to its original state.

Reset Mi Account Redmi 4x

First stage

To disassemble the gadget, you will have to use a plastic card and a screwdriver. Don’t forget to unplug the power cable for the fingerprint sensor. After that, the cover is removed. There are 2 pins next to the camera module. They are needed for firmware.

Second phase

Install on PC MiFlashSetup.MSI (available in the public domain). Remember to associate the software with an administrator account. You will need driver 1.4.3 (ADB) to work. It is installed separately.

If you have any difficulties, please contact here.

Flashing stage

Turning on the computer, run the program, select the directory with the software version. Further:

  • Disconnect the lead battery cable.
  • Connecting the phone to the cable.
  • We close the contacts (clip).
  • We connect to the port of the system unit or laptop.
  • Hold down the paperclip for a couple of seconds. After that, remove it. In the interface, the device will be defined as 10 COM port. If this does not happen, click Refresh.
  • The firmware method is selected Clean All. Next you need to click on Flash and forget about PC for 6-10 minutes.

Final stage

After the process is completed, you need to return the battery cable to its place. Next, press the power button.

Important: The download process will take up to 15 minutes. When finished, skip any external connections. Should not have a SIM card or WI-Fi.

Opening the settings:

Select the line with the version of the MIUI shell.

Development mode will turn on. Already through it we activate debugging via USB. After that, you will have to download an additional utility. It is called WTUMA.exe. Used to unlock an account. Run it as administrator and connect the gadget with a cable to the PC.

Next you need:

  • Activate account lockout (Unlock).
  • Confirm selection on smartphone.
  • After the error notification appears, we do nothing. The phone will reboot automatically. Ready.

Important: after what has been done, do not disable or change anything in the settings. Touching debugging and developer mode is strictly prohibited. Otherwise, you will have to do everything from the beginning.

Telephone repair

Reset Mi Account Redmi 4x Xiaomi Repair Manual

To reset your Redmi 4x Mi account, you can use one of the proven Xiaomi repair methods. Let’s start with a simpler and more effective.

  • Guys what to do. On Xiaomi, it requires a password from this damn account. And I don’t even have a password. The child did something there, but he does not know anything. How to remove this password? The phone has been lying like a brick for 3 days.
  • I have a Xiaomi Redmi note 4 and a blocked Mi account. Can someone help me to remove this blockage. You just need to step by step with all the details. Because I myself will definitely not figure it out, the system is too sophisticated.
  • Help to remove the account with a password with xaomi. I’ve already read some forums. Even tried different instructions. Nothing helps.
  • Reset Mi account Redmi 4x is possible without contacting technical support. True, for this you will have to arm yourself with a screwdriver. Warning: this method is only for those who understand what they are doing. After following the instructions, all associated applications will stop working.

Attention! We are not responsible for all your manipulations with the phone, performed according to our instructions. Repairs must be carried out by a qualified technician. Contact our Repair Service.

When the quality of the pixels is determined, and among them it was possible to detect “burnt out”, you can start looking for applications that will correct the situation:

  • JScreenFix is ​​easy to use, you need to use the Fix Stuck Pixels button to get started. The developer promises 30 minutes to complete this operation, but the service center masters recommend leaving the devices. At least 10-12 hours for a more complete check;
  • Pixel Fixer: Another program similar to JScreenFix. To restore the pixels, you also need to click on the green button;
  • “Dead Pixel Treatment”: The platform not only tests a mobile phone for dead pixels. And then “heals” them, but at the same time reveals other defects in the display.

When using applications, it is recommended that the device not be disconnected from the chargers for the duration of the “treatment”. During pixel processing, the smartphone is constantly on, so the charge may not be enough.

Screen microcracks are fraught with a break in the power circuit. If this happens, then you will have to change the screen. Fortunately, in China they are several times cheaper.

It happens that the malfunction lies in the incorrect installation of the SIM card or flash drive. Try to take them out and see what happens.

A card with problems can be repaired by restoring broken clusters using a PC.

If shaken, a badly exposed plug from the display may fall out. What will entail disabling the image transmission module, or partial shutdown.

Remove the cover of the device, and plug the cable into the socket. If it is inserted, then take it out and insert it. In this case, do not forget to disconnect the power cable from the battery.

Actions, how to act in such a situation

Changing graphics to low resolution will help. It is required to limit the power consumption mode. Do not continue to play with the phone charger turned on. Remove the phone from the case, allow general ventilation of the case. Turn off phone, remove battery.

If the smartphone was in a humid room, or moisture got on it. This is especially true of the USB input, and leakage into the smartphone. Oxides can lead to current leakage, and this contributes to the heating of the device. To fix, you need to clean the USB. Take a thin stick and wrap cotton wool around it. Dip it in white spirit or alcohol, and wipe the contacts at the entrance.

If water got inside, then you need to disassemble Meizu. And, carry out the same operation with contacts that are attached to the board. But, before doing this, disconnect the battery cable to avoid a short circuit.

If Meizu M8 does not have a microphone, for this you need to do the following.

Open the security settings, look for root access and click accept, reboot the device. Open the “phone” and enter this combination ##54298## or ##3646633##. Scroll to the right and find ” Hardware Testing “. audio. Audio Playback set the value of Heaset PGA to 160. Exit the menu and reboot the phone.

Also, software methods can be used. But, they can only help if there are no malfunctions in the device itself. This method is one of the simplest, we open the settings on the mobile phone. And, select the command “reset settings”. Keep in mind that this means deleting all data from the smartphone.

So that the stripes on the Meizu M8 screen do not bother you, you need to:

  • Make sure the integrity and reconnect the display module cable;
  • Replace the screen completely if there is real damage;
  • Update firmware and Flyme shell.

In the first situation, contact could simply be broken. The connection came off due to impact, the contacts are clogged or the display was not fully connected at the factory.

In the second case, it is recommended to contact the warranty specialists or an independent workshop. The third option indicates that you bought a phone with an outdated software version. Which has flaws fixed in updates.

To carry out this procedure, you need:

  • Enter the device settings;
  • Select “About phone”
  • In the submenu, you will need to select check for updates. when you turn on Wi-Fi, everything will start downloading;
  • The device will reboot.

The appearance of stripes during use can be eliminated immediately after purchase by updating. This will not void the warranty. Unlike a complete flashing or self-repair in the same period.

A banal method is to simply log into your account on the device. Click on the item “Delete Mi account” below.

In this case, the account will be unlinked from the mobile phone. There will no longer be a message when the machine is booting up.

If Xiaomi has lost sound, you should first check the audio settings. If there is an active mode (with sound), then we continue to look for the problem.

Necessary. clean the headphone jack.

If the headset icon is on the screen of the Xiaomi smartphone, and the headphones are not connected, it means that the contacts are shorted. Therefore, the sound is transmitted to the headphones, even though they are not physically connected.

Reboot your phone after cleaning.

If during a call the interlocutor does not hear you well, then this function may be disabled. Go to the “sound and vibration” settings and move the “noise reduction” slider to the value “on”.

If it is activated, and there is crackling and noise during the conversation, then try turning off the function.

The built-in mobile assistant can also interfere with the normal operation of the microphone. Go to the settings menu. search Google. Next, turn off the voice finder feature. Restart your Xiaomi phone.

You can reset your account using Xiaomi support.

To do this, you must have documents on the phone. to confirm that it is not stolen.

How to talk to Xiaomi technical support.

Go to your mail service type and log in.

Click create message. In the first line, we write this address: mishu@Xiaomi.com Or this one: service.us@Xiaomi.com You can write in the subject (Unlock mi account). You must write in English. Use an online translator.

Next, we write what is required. I want to reset my Mi account on Xiaomi Redmi 6a. This procedure is long and may take 2-3 weeks.

Choose English and any country;

We make an Internet connection using Wi-Fi or cellular data;

We go to ” Privacy Policy” (Security Policy) and select any piece of text. On the right, click on the three dots, “Web Search” and “Google App”. Next, we can go to the settings by clicking on the “Settings” entry. We are looking for the item “About Phone” and click on it.

Xiaomi Redmi 4X Fingerprint Set Up and Speed Test

After logging in, click on “Software version (Miui version)”, which you need to quickly click a few (about 5) times until a notification appears about granting “Developer rights”. We go back and go to “Second Space”, and then “Turn on second space”.

Here a second space is created and the device is already quite ready for work. Nevertheless, after the reboot, everything will be reset and you will have to do everything again, so we continue. We go into the settings, then “About Phone”, “Additional Settings” and “Developer Menu (Developer)”. Move switch USB Debugging to the enable position.

We connect to the computer using USB and start Switch. Download “Minimal Adb and Fastboot” and turn it on. We go to the first desktop, and on the computer we type “adb devices”. Here we enter the following command: adb (introductory command) shell pm uninstall (parameters).k.user 0 (values) com.Xiaomi.finddevice (server connection);

Delete “Find my phone (Find my phone)”.

Nuances after such a decoupling.

After that, the gadget is ready for full operation: you can go online, use various programs, etc.

However, it is worth noting that it will not be possible to use Xiaomi services. Which is explained by the absence of the account itself. There are a lot of complaints about the Xiaomi account from users due to poorly executed software, and it is quite logical that it is deleted.

Light indication on Xiaomi smartphones

A smartphone is a device that constantly receives a large number of signals from the outside, allowing the user to always stay up to date with important events. Now the market leaders are competing with the Xiaomi brand, which is gaining popularity every day due to high quality, low cost and a wide spectrum of pleasant bonuses. This is the indicator light in Xiaomi Redmi 4X. It signals the user about unread messages, calls or notifications.

Light indication in different Xiaomi models

However, the function of selecting different colors is not available in all Xiaomi devices. When choosing a model among smartphones of this brand, you should pay attention to its cost; budget options often do not include this feature. In the Mi 6 model, for example, the LED lights up only white, and all that is available to the user is to turn it on when unread notifications or charging. And Xiaomi Mi5 has a rich palette that you can customize to your taste or expand with special applications. Xiaomi Redmi Note 4X also has a customizable color indicator.

Xiaomi light indication and what it means

LED is a small light bulb built into a smartphone to signal the user. Sometimes the red indicator flashes, sometimes yellow. Each of the colors means a certain state of the phone. There are several universal symbols automatically configured in the gadget (but they can be easily changed):

  • Yellow light. This is a signal that the power saving mode is on. This state of the phone is reflected in synchronization, background application processes, automatic software updates, Wi-Fi and mobile Internet connections, and GPS. Yellow battery indicator lets you monitor power consumption.
  • Red light. If the red Xiaomi signal blinks and the phone does not turn on, it means that the battery is completely discharged. The gadget needs to be charged for some time before it starts to turn on again. However, when the charge level is low (less than 20%), the red LED also lights up after switching on.
  • Green light. Shows the owner of the smartphone that the phone has already passed the minimum battery charge threshold, and it can already be used. If the gadget is fully charged, the indicator goes out.
See also  When a computer is turned on, the monitor writes no signal

LED can be customized, which means that a certain color here can be chosen to your taste. So, with each unread message, the indicator can glow pink, and orange will be on for unread notifications or when the power saving mode is activated. The palette depends on the Xiaomi model, but it can always be expanded using applications with keywords (LED Control) in the name.

Light indication setting

Notification light color is auto-matched yet easy to customize.

How to turn on LED on Xiaomi? You need to go to settings. Then go to the System and device section. After that, find the Advanced settings or the Advanced subsection (depending on the device model). There, select the indicator light. Then you can turn on the light indication when charging, as well as when receiving notifications, with one click. It is easy to check the operation of this light bulb: just put the phone on charge.

functional Xiaomi models offer the ability to make the indicator light up in different colors for different notifications and applications, depending on user preferences.

How to change the color of the notification indicator

In Xiaomi Redmi Note 4X, the notification display is configured in the same way. In the Light indicator section, under LED turn on features, there are three sections: notification light, call light, and message light color. You must select the first one and indicate your preferred color in it.

You can also set a separate color for notifications of different applications. Just go to the settings, then find the All applications section. There, select the one you need (the most convenient way is to distribute different colors across instant messengers, social networks and email). At the top, click Notifications, then find the Light indicator (next to the Lock screen, Sound, Vibration), turn it on and select a color (if the model supports this feature).

Display problems

It is not uncommon to have problems with LEDs on Xiaomi. If the notification indicator does not work when unread notifications arrive, it is worth checking the settings: they may have gone wrong, and the light bulb is simply turned off. If earlier the LED glowed in different colors, but now the light is dim or the indication has completely stopped working, you should consult with specialists. You may need to replace several items. The indicator may become faulty after exposing the smartphone to sudden temperature changes and strong impacts.

Problems when connecting the phone to the computer and their solutions

Let’s figure out what to do if the PC does not see the Xiaomi smartphone. It is rarely possible to immediately identify the problem, since there are dozens of options. Separate failure solutions that are relevant, for example, for MI5S, will not work if you do the same for another device. Therefore, only those who are well versed in their phone will be able to understand the problem. Nevertheless, we highlight the most common ones that are found on all gadgets.

Problem 1. Non-original cable

There is a small chance that trying to connect with a non-original USB will result in your Redmi 4A not being detected by Windows.

Solution. Make sure the cable is original. If not, then try to find exactly the same in the online store, from retailers in your city or order from China.

Problem 2. Drivers

The lack of a set of drivers in Windows for one reason or another will lead to the impossibility of connecting a smartphone to a computer.

Solution. You need to find out if your operating system supports automatic loading of drivers, check their availability and version, clarify when they were updated and whether they were updated at all. It is important after connecting the cable to the computer and smartphone to watch the notifications of the Windows system. She usually reports that the process of selecting drivers is underway, and at the end she says whether they were successfully installed or not.

If the installation failed, then you can download them manually. In the themes of almost all Xiaomi phones (such as Redmi Note 4X or the flagship MI6), there are threads on the forums where you can download the latest drivers. After they download, you need to do the following:

  • unpack them (if it is an encrypted archive);
  • install it in a separate folder;
  • insert the cord into the phone and PC, click “My Computer” with the right mouse button, go to the “Device Manager” tab, a new connected device will be displayed there, which is the phone;
  • right-click on it and select “Driver”, now “Update”, then specify the folder in which the drivers were installed.

The instruction helps, but remember that gadgets are unique, and approaches to Mi A1 may differ from those that are relevant for the same Xiaomi Redmi 3 Pro. If it does not work, refer to the topic of your device on the forums, read the instructions and tips. Nearly 100% chance there will be a clue.

Reason 3: Incorrect connection method

It doesn’t usually happen, but it does happen.

Solution. Check again that the cable is firmly seated in the socket and that the USB port on the PC is working.

Reason 4. Errors in the firmware

Crashes occur in custom and sometimes official firmware. It is difficult to solve such a problem, often it is done by a radical method.

Solution. You need to do a factory reset or change the firmware if the first option did not help.

It is worth doing this as a last resort, when you have already tried to do everything that is written in the article, and also studied the topic on the forums. Flashing Xiaomi MI5 and Xiaomi Redmi 3S will be different, so look for a separate detailed instruction. Remember that you need to make a backup.

How to Set Up XIAOMI Redmi 4X. Configuration Process

A better option would be to ask a question to knowledgeable people or take your Xiaomi Mi Max or Xiaomi Redmi Note 3 or another smartphone to a service. After all, there is no 100% guarantee that flashing will help fix everything, and an inexperienced user can do such things that problems with connecting to a PC seem like a trifle.

Ways to connect Xiaomi Redmi 4X to a computer

Connecting Xiaomi Redmi 4X to a computer allows you to significantly simplify the work with the gadget and expand its functionality. Connect helps to carry out a number of manipulations, including:

  • data transfer (music, photos, documents);
  • using a smartphone as a storage device;
  • updating the firmware or installing custom builds;
  • Debugging, Getting Root and System Changes.

Often the connection occurs without any problems, but there are times when the computer does not recognize the device. We will look at popular ways to connect the device to a PC, as well as analyze the problems that may arise and their solutions.

How to connect to a computer?

Connect should almost always be done via a USB cable. This method will provide full access to the file system and the ability to modify the firmware.

Windows XP, newer builds are programmed to automatically pick up drivers for Xiaomi MI4 and other models, so you most likely don’t even have to do anything.

The only thing to do is to perform the following simple steps.

  • Connect the cord to the Xiaomi Redmi Note 4 socket, and insert the other end into the USB port on the PC.
  • In the pop-up window on the computer desktop, select what to do with the connected device.

This is all that is required by the vast majority of users, but sometimes there are problems in the process, or when connected, only charging goes on, but files cannot be transferred. This usually happens on devices that do not have a global firmware, so they are running localized builds of MIUI or custom systems based on Android.

Other Ways to Solve Problems

Be sure to try these tips, if others did not help, they will help to avoid flashing.

Connecting in active camera mode

If the device is not recognized as a file drive, then you should try turning on the camera, this may help bypass the problem. To do this, the files to be reset should be transferred to the smartphone gallery, which will be available, and then moved to the desired directory on the device. By analogy, drop documents, for example, from a Redmi Note 3 Pro smartphone, first to the gallery, and then to the PC.

Activating USB Debugging

Often this helps to eliminate connection difficulties; you can activate debugging through the developer mode. It’s not difficult to turn it on, you need to click on the MIUI version 7-10 times in the “About phone” settings item (if you have a custom on Android, then tap on “Build number” as many times in the same paragraph).

  • In MIUI, go to “Settings” → “Advanced” → “For Developers”. Find there “USB debugging” and activate it.
  • On Android, go to Settings → Developer Options and turn on USB Debugging.

Connect your phone to the computer and see if the choice of connection method appears in the blind, if so, then click on MTP or “File Transfer”. If there is no choice, and the device is still not visible to the PC, then “Debugging via USB” did not help.

Terminal usage

The method is complicated, it is for experienced users or for those who are not afraid to sit and understand their smartphone. It is suitable for any model, even if you are faced with the fact that the old MI2S will not connect to the computer in any way, the method will surely help.

  • download Android terminal emulator on Google Play (you need Root rights to work);
  • write the line “SU”, confirm the action, then enter “setprop persist.sys.USB.config mass_storage, adb” and press “Enter”;
  • restart the phone by typing “reboot” in the terminal;
  • download QCustomShortcut (the application allows you to access the connection adjustment, but it is not on Google Play, so download it from the Internet);
  • in the “Package” field, write “com.Android.settings”, and fill in the “Class” block with the text “com.Android.settings.UsbSettings”;
  • tap on “Create Shortcut” and that’s it.

Now, when you go through the shortcut, you will immediately be taken to the connection settings selection menu.

If none of the above recommendations help, then you should consider taking the phone in for repair or reinstalling the operating system.

Installing TWRP Xiaomi Redmi 4x

Hello everyone, today we will consider an interesting topic about how to install custom recovery TWRP (Team Win Recovery Project) on Xiaomi Redmi 4x, how to use it and why we need it. Let’s get straight to the point if you want to install some kind of custom firmware or kernel, get ROOT rights or backup your phone, then you can not do without twrp. twrp has a fairly clear interface, supports various languages, including Russian, control is carried out using the touch screen.

Installing TWRP

First of all, we need to check the bootloader, if you have it unlocked, then everything is fine, read the post further, if not, then check out my article on unlocking the bootloader Unlocking the Xiaomi bootloader, because if you have it locked, you won’t be able to install TWRP!

So that the phone does not become a brick during the installation of the recovery, we check the charge of the phone, I advise that the phone be charged at least 30%.

The next step is to install the drivers on your PC. Download this ADBdriverv1.17lite archive, extract it from the archive and run setup.exe if you have an x64 system, and if you have an x86 system, then you need to run setup_x86.

Click on the next button and wait for the drivers to be installed.

4.Now download the archive itself with twrp TWRP_3.1.1 Redmi4x_miui unpack it.

We put the phone into fastboot mode, for this we hold down the power and volume keys until a hare with the inscription fastboot appears on the screen

We connect the phone to the PC using a USB cable and open the folder with twrp, which was downloaded in step 4. Find the Flash-Redmi 4x TWRP file and run it

A blue window appears in front of us in which you need to press the enter key 4 times to continue, which we do.

Now we look at the phone’s screen and see that we have launched custom twrp recovery, now the phone can be disconnected from the PC, select the language you need and swipe to the right. This completes the installation of custom twrp recovery on the Xiaomi Redmi 4x phone, but there is one more small nuance, if you are not going to flash the phone right away, then you need to go to Advanced / Tools and click check in Boot. This disables the encryption check in boot, since your firmware may simply not boot.

How to enter twrp

In order to get into twrp again, you need to simultaneously hold down the power and volume buttons and

What is twrp for?

As mentioned earlier, twrp is used to install custom firmware, install root rights, custom kernels, various patches and, of course, create backups. I advise everyone before doing any manipulations with the phone, do not forget to make backups! You do all the manipulations at your own peril and risk, here I describe the principle of action that was used by me. If you have any questions, ask them in the Комментарии и мнения владельцев, I will be happy to answer everyone.

In the next posts we will look at installing custom firmware and kernels via twrp, creating backups and making the indicator light colored.

up. I updated the archive from TWRP to the previous version 3.1.1, as in version 3.2.3 the partition was encrypted and I had to do a full reset. up. To install custom Treble firmware, you need to install TWRP with Treble support, the installation is carried out in the same way as described above. TWRP_Treble_3.2.3-0_Redmi4x Up. TWRP 3.1.1 works fine on miui global 10.3.1.0 firmware

How to disassemble �� Xiaomi Redmi 4X Take apart Tutorial

What to do if the computer does not see Xiaomi Redmi 4x?

Sometimes trouble can happen when connecting the computer does not see Xiaomi Redmi 4X. It interferes with moving files between devices and syncing data.

The reasons why the PC does not see the Redmi 4X phone may be different. Fortunately, most of the problems are not serious, so fixing problems is not difficult.

Consider possible causes and ways to eliminate them.

These tips are suitable for most Xiaomi phones.

This type of connection provides for the synchronization of photo and video files, so the main storage of the phone on the PC is not displayed. In other words, if Redmi 4x is connected in this mode, it will not be possible to use it as a removable media.

You can change the mode through the connection notification in the quick access menu: pulling out the curtain, you need to click on it and select the item “ File transfer».

In most cases, the above methods help to fix the problem due to which the computer does not see Xiaomi Redmi 4x, however, there may be such reasons for the problem:

USB cable not working

If the wire has been damaged, then the smartphone and PC will not be able to recognize each other. At the same time, the computer and phone can even respond to connecting to each other.

Carefully examine the cable and its contacts for damage. Naturally, the only solution is to buy a new USB cable.

Broken micro USB slot on phone

A burnt or broken connector is a very annoying problem. They are solved exclusively by replacing the slot in the service center.

Problems with micro SD

Sometimes the internal storage of the device is displayed, but the computer does not see the memory card. In this case, try to get it out of the connector, restart the smartphone and insert it back. If this does not bring success, it is worth contacting the service, since the problem may lie in the breakdown of the card itself or the slot.

If you know other causes and their solutions, please share them in the Комментарии и мнения владельцев.

Denial of responsibility | Contacts |RSS | SE | EN | BR | DE