TV Lg 42 Inch No Image

Nowadays, a rare person does without a TV. Each year, the models are becoming thinner, larger and offer more and more new and new features. Modern plasma panels with Smart TV technology have little in common with devices that were sold some ten years ago. However, the same thing remains between the old and new generation. breakdowns and malfunctions still happen. The reasons for this can be very different: shock, fall, moisture and direct sunlight or elementary marriage. In this article, we will consider in detail what to do if the TV has lost an image, but there is sound. Let’s get it right. Go!

TV Lg 42 Inch No Image

What to do if there is no picture on the TV

First, it should be noted that such a malfunction occurs quite often in a variety of TV brands. Televisions of all brands are equally affected by this: Samsung, LG, Philips, Sony, Panasonic and many others. Therefore, it makes no sense to blame the manufacturer.

There are many reasons for the lack of an image on the screen, and it is unlikely that you will be able to determine it yourself by eye. Most likely, you will have to contact a service center or another repair service. It all depends on the nature of the problem. on this below.

It happens that when you turn on the TV, the first screen saver appears with the manufacturer’s logo (LG, Samsung, Philips, and so on), after which the screen simply goes blank. In doing so, you can switch channels and hear sound. Some users noticed that after a while the image appears, but when you turn it on again, everything repeats and the picture is missing. In this case, try the following tips:

  • Check the connection of the receiver cord, as it could disconnect. Make sure the cord is connected securely. If there is no signal from the set-top box, many televisions simply blank the screen.
  • Also, the problem may be in the cable itself. The wire may be damaged or just may be of poor quality. This concerns not only HDMI cables, but also cables with “bells”. In them, the transmission of the audio signal and the signal occurs on separate wires, and the problem may lie simply in a broken wire or poor contact. In some cases, replacing the wire allows you to correct the situation.
  • Check the power cable. It must also be securely connected.
  • Some users have found a rather original way to solve the problem. to increase the volume to maximum (or close to it). After a few seconds, the image will appear and then you can set an acceptable volume level.

Please note that all the tips above will only help if the screen is working. This is indicated by the screen saver when you turn on the TV. If the screen saver is missing and the screen is constantly dark, this already indicates that some component of the TV responsible for the image has failed.

There are several components whose failure can cause the absence of a picture on the screen. Quite often there is a breakdown of the inverter, which supplies voltage to the backlight. The lamps themselves can also fail, and this, in turn, provokes a breakdown in the power supply. In addition to the above malfunctions, a matrix or system board breakdown is often found. Also, the problem may lie in the loops, converter and decoder. In this case, non-working parts and elements will have to be replaced with new ones.

Performing repairs yourself is not recommended, since modern TVs are quite complex devices, and you run the risk of exacerbating the situation even more. If the above simple tips did not help, then the best decision would be to turn to professionals, since disassembling the TV will be required. This can be a service center of a manufacturing company or a private office, where repairs will be carried out efficiently and promptly.

One way or another, it is impossible to determine the reason for the failure of your TV without a thorough inspection. In any case, the device must be disassembled and diagnosed for non-working parts and components. This is best done in a workshop with appropriate conditions, however, if you do not like this option, many telemasters provide all these services at home.

Of course, replacing some parts can cost a pretty penny, but it should be noted that matrices or motherboards themselves fail extremely rarely. Typically, a breakdown occurs as a result of physical damage to the part, for example, when the TV falls or moisture gets in. In general, you won’t do without a telemaster.

Now you know what to do if the TV has lost the image, but at the same time there is sound. You will also understand what could be the reason for this malfunction. Write in the comments if this article was useful to you, share your experience in solving similar situations with other users, and ask any questions of interest to the topic of this article.