The computer does not see other computers online

The reasons and methods of correcting the Windows error cannot gain access to the computer

To create a local network at home, users of personal computers connect them to each other. This allows you to use the same local network on all machines to get joint or limited access to resources, files and catalogs on hard drives. It also organizes remote access. Sometimes, when setting up, people meet with an error that prevents one computer under the control of the Windows system to access another computer in LVS. A today’s article will be about the methods of eliminating the error, which will tell you what to do if Windows cannot access the computer in the local network, and there is no access to the common folder.

The mistake itself is complex and confusing. One of the reasons for its occurrence is the case when the network after setting seems to function correctly, but the user introduces an incorrect path. It is important to understand that any path in the local network should have a common resource permissible for viewing on remote personal computers, as well as certain access rights to this resource. Further, steps will be disassembled in detail to eliminate this problem associated with the lack of connection to certain files, folders or computers, when the network path is not found or the descriptor is incorrect.

Methods of solving the problem

Error correction is directly related to what caused its appearance. If you could not determine the exact cause, then act in order, considering separately each item of the material. If the reason is diagnosed, study the information related to a specific factor affecting the detection of PC.

Checking the name of the working group

The name of the working group is not a formality. On every computer that includes it, the name should be the same. An error at least in one symbol leads to the fact that the detection does not turn on. To solve the problem is required:

Make sure that all computers on the local network indicate the same group name. Otherwise, the connection will be disabled, and you will not be able to detect other devices.

Checking parameters of general access

Windows 10 settings regulate the ability to detect computers within one local network. If the option is not launched, then the devices will not be displayed in the list. Therefore, to solve the problem, you need to enable network detection:

  • Expand the settings of a guest or public network, and then install the checkbox at the “Turn on network detection” and “enable general access to files and printers”.

By analogy with the previous method of eliminating problems, it is necessary to repeat the operation on all computers included in the working group. The absence of one or another device on the network will be evident that the general access is deactivated in its settings.

Setting up the “Route and Remote Access” service

It happens that the display of computers on the network does not work due to deactivation of the service responsible for remote access to PC. In this case, it is necessary to enable it forcibly:

  • In the proposed list you can see “routing and remote access”. It is this service that we will need, so click on it twice LKM to launch settings.

Important. After changing the parameters, open the general service menu and make sure that the required parameter is launched. If the “Launch type” line displays the “disabled” value, then you will need to open the service settings again and start it forcibly, clicking on the corresponding button.

It is easy to guess that the proposed actions must be performed on all devices included in the working group, and not just on the PC, where other computers are not displayed. The problem is not hidden in detection, but in activating the remote access function.

Resetting routing settings and restarting network

Often on a computer, identification is not active due to the occurrence of system failures. As a rule, they touch on routing settings, so manual change in parameters does not help to eliminate problems. At the same time, there is an alternative action plan involving reset and restart the network. To perform the operation, you need to contact the instructions:

  • Enter the requests “Netsh int IP Reset Reset.TXT ”,“ Netsh Winsock Reset ”and“ Netsh Advfirewall Reset ”, accompanying each of them by pressing the“ Enter ”key.
  • The above commands must be entered on a computer that does not see other devices on the network. At the same time, the request “Netsh Advfirewall Firewall Set Rule Group =” Network Discovery “New Enable = YES on all PCs included in the working group is required to enter.

Thus, you will get rid of an error associated with the detection of computers, as well as forcibly run the remote access service. At the same time, do not forget to install all the necessary equipment updates through the device manager, since the absence of current drivers often affects the performance of certain PC functions.

See also  What to do if the wire does not charge the iPhone

Method #2 Turn on the support of the SMB1 protocol

The factor that Windows 10 does not see the network environment may consist of SMB1. It is possible that it is disabled. Activating it will not be difficult:

After that, the problem will disappear when Windows 10 does not see network computers. If not, the problems are caused by other factors, the methods of elimination for which are present below.

A computer with Windows 10 is kicking, but not visible on the network for other computers

We will proceed from the fact that the IP address in the problem computer. DHCP settings on the router are made correctly, the computer responds to the Ping command. The first thing we do is click on the “TV” icon in the task panel and go like to

We need to first check the parameters of the general access. Let’s start:

Start making settings from your current profile. Now we include network detection for it and, if desired, you can configure access to common folders and printers:

That’s not all; I recommend making the same settings in the “guest or public” network.

And in the “All Networks” section we make the following settings:

If there are common folders and printer on the computer, then access to them can be organized either with the entry of a password of the current PC user, or without. For unhindered access to computer resources, overall access with password protection can be disconnected.

To access the common photo (optional) and the video you can configure the flow of them over the network. If desired, other users will view them. What has shown now. We look at these settings first.

The next item is the connection property. You noticed that the system provides for three types of network. Home, private and publicly available? Each provides its own level of privacy and safety settings. Sometimes it is enough to switch the type of network from one to another:

We select the desired profile (see above) the one on which all the settings are already made for network access: (I have “private):

And the last thing to check is the firewall. Often, he begins to block the compounds:

If you have a common scanner on your network, then I recommend turning off the firewall completely (but later you can try to configure exceptions for the scanner):

The setting “Network” recently appeared here recently. If suddenly the network cards on your PC, then this option deleys them from the system, after the reloading process it puts them in the system again, as if from zero. Helps to figure it out when nothing is clear as you can see, nothing complicated. The whole process takes about five minutes.

I used to face similar problems when firewriters and antiviruses were installed in T.C paid. After updates, all connections were blocked. If there is such that you do not need to turn off. Good luck to you!

Step-by-step instruction

Note that situations when a computer is not visible on the network is a familiar business in the latest versions of Windows. Despite this, built.In diagnostic and support tools often give out absolutely useless solutions.

Therefore, we offer to plunge into the problem a little deeper and check the work of the relevant services. As practice shows, this method helps in most cases.

All operations are carried out precisely on the computer that is not visible in the local network.

Open the “Perform” menu. You can find it in the “start” or call it with a combination of Winr. In the line opened, introduce: Services.MSC.

A window with a long Windows services list will open.

In the window you can see the state of service, status (either an empty field works), the type of launch (automatic or manual) and the line “Entrance on behalf”.

computer, does, other, computers

By clicking on the service you need, you can change its settings. Or just “run” for inactive.

You need to check all the points of this list:

  • DNS client
  • Host of the supplier of detection function
  • Server
  • Publishing of function detection resources
  • Universal PNP devices
  • SSDP detection

Most likely, the computer is not visible in the local network because one or more of these services are inactive. Run them. So that the problem is not repeated, click on the service with the right button, go to the “Properties” and in the “General” tab change the launch mode for automatic. Check that the parameters are set for all services from the list above.

After all the settings, reboot a computer that is not displayed on the network. If you did everything right, most likely, you will not have such difficulties in the future.

Note that this method is not universal, but often helps ordinary users who do not know about the work of various Windows services. To carry out this procedure, making sure that the computer is in the same working group as others. Checking the launch of services helps in situations where more and more simple options are tried, and the computer is still not visible on the network.

We hope that this instruction was useful for you. Stay with us and find out many more useful techniques for working with PC!

Antivirus or firewall can block network devices

If your antivirus, or firewall (firewall). Which is installed on your computer something did not like something, it can easily make it so that you can not see other devices in the network environment, no one can find you.

True, after disconnecting the Faerwole integrated in the antivirus, the problem was not solved (which means that the problem is most likely not in it). But everything seems to me that in my case, without the participation of the antivirus, there were not.

Therefore, try temporarily stop the operation of the antivirus for a while, or at least turn off the firewall built into it (inter.Grid screen). In NOD 32, this is done like this:

See also  Why Samsung does not connect to Wi-Fi

To verify this, this must be done on all computers that will participate in the local network.

It is possible that you have some other programs that can monitor the network and manage network connections.

If it turns out that the problem is in the antivirus, then you need to add your network to the exceptions. Forbid the firewall to block the network itself, or network devices.

If you do not have antivirus, then you can experiment with the shutdown/turning on the firewall built into Windows.

Solutions

The very first thing to do if the computer stops seeing other devices is to restart it. If the reboot did not help, then there are several solutions to eliminate the problem.

Connection check

It is necessary to check if the network cable is connected correctly to the computer. It happens that the cable connector did not fully enter the fee. Когда коннектор полностью входит в порт сетевой карты, слышится тихий щелчок. After that, it will not be possible to pull out the cable, simply pulling it by the wire. A special process on the Connector performs the function of the latch. And if you don’t press it, the cable will not work. This check should be done at the other end of the Lan Cabel, which is usually connected to network equipment.

Note! It is necessary to make sure that the network cable has no technical damage. Check if the network card is enabled. To do this, cross the start \ control panel \ center of control of networks and total access \ Changing the parameters of the adapter. If the icon “Connection on the local network” is gray, then you need to press it with the right mouse button and select “Turn on”.

Check connection

For this check, you need to find out the IP address of any computer connected to the network. After that, open the start \ all programs \ standard \ execute, or press Winr. In the opened window, enter the CMD command. The command line should open. In the new window, write the following command: Ping (IP address of another computer).T and press the Enter key. With a successful attempt, messages will be released: answer from (entered IP address) number of bytes = 32 Time = 16MS TTL = 36. All numbers except address may vary depending on the speed of the network.

If the message “Determined node is unavailable” or “exceeded exceeded awaiting request”, then you should re.Check the connection.

Important! If the physical problem is not found, then you need to turn off the firewall or antivirus and re.Run the check.

Checking the working group and name

Press with the right mouse button on the “My Computer” icon and select “Properties”. In the opening window, in its right side, select the section “Additional parameters”. Go to the “Computer Name” tab. Opposite the “Working Group” inscription, the name of the working group used on the device will be shown. It should be changed if it does not coincide with the name of the group used on other computers. Click on the button Change. In the bottom of the window, replace the name of the working group and click “OK”. The name of the computer is not necessary.

Checking IP addresses

In addition to checking the IP address, it is also worth finding out if the network is controlled by DNS servers. This data can be obtained from the network administrator. And also find out the free value of the address. If there is no network administrator, then you need to record the data of some data from the computer with which the network works. To do this, go start / control panel \ center control center and total access \ Changing the adapter parameters. Click with the right button on the icon “Connection by local network” and select “Properties”.

Windows 10. Can’t Find Other Computers on Your Local Network?

In the “Network” tab, select “Interneal Protocol version 4 (TCP/IPV4)” and click on “Properties”. It is necessary to write out all the addresses in this window. All recorded data must be used with data on a problem computer. All numbers should match, except for the latest IP address numbers.

Important! In the local network, the device with the same IP addresses will not function.

Including network detection

Network detection settings are: “Start \ Control Panel \ Center for Control of Networks and General Access”, tab “Change general access parameters”. Both points are required to include here.

Reset

After resetting the settings, all addresses should be re.Prescribed, so it is important to save or write them down. To reset on the command line you need to register Netsh Winsock Reset and click Enter. The second command “Netsh int IP Reset C: \ Resetlog.Txt “is prescribed in the same place. After that, the computer should be reloaded. All network settings will be pumped up to factory.

The above methods eliminate the main errors. After performing all the actions, the computer will see in the local network.

Podgornov Ilya Vladimirovich all articles of our site are auditing a technical consultant. If you still have questions, you can always ask them on his page.

Windows 10 does not see computers on the network: the reasons and their solution

The first swallow was updated 1703. When installing it, the computer “blinded” himself and stopped correctly displaying other cars. They simply disappeared from the network environment. It was also possible to detect an error with standard viewing of neighbors from the command line using Net View. Instead of a list of available PC, only a message about the absence of elements was displayed.

If a similar situation arises, first view the system parameters of accessibility. In Windows 10, they are often the reason why the OS does not see computers on the network.

In it, open net control. This element is also responsible for the correct operation of access functions. An alternative way to switch to it is to call the right click on the menu connection icon and click on the same name.

See also  How to find hidden apps on Samsung

Next, open additional parameters.

Important! The connection profile should be installed in the value of the private network, otherwise Windows 10 does not see other computers and vice versa (instructions see. Below).

Next, check the following parameters and, if necessary, translate them into the state (put the checkmarks):

  • Network detection and automatic setting mode;
  • Permission for external access (allows OS to communicate with printers and shaved files);
  • The rights to manage the group transferred the OS.

It is necessary to adjust the profile designed to work with any networks, correcting its parameters as follows:

  • Connect access mode. This is necessary so that users from other PC can not only see open folders, but also read/record data in them.
  • Only for those networks in the safety of which you are 100% sure (in real life it is not recommended to remain in the illusion that any network is such): turn off the password protection so that anonymous users can also perform any operations with network folders.

The next item will come in handy if another user (or you from another computer via a local network) does not see your car under the control of Windows 10. Working with Windows parameters will be required.

Next, go to the subparagraph of the network and the Internet.

Finally, select Ethernet for a computer with a wired connection, or Wi-Fi if it does not see Windows 10 in a wireless network. Turn on the setting that makes PC available for detection.

The base part is completed. Further actions will come in handy if this is not enough to correct the problem.

Tuning the firewall

Sometimes it is required to additionally carry out operations from the command line, and by launching it under the administrator account by Win-X.

In the terminal, you need to run the command to install the rules for the system firewall, which allows detecting.

Re.Adding to the group

The next option for correcting the situation when Windows 10 refuses to obey and does not see other computers in a normal network environment at all. Re.Entering the car into the group.

We use the control panel. To fix it is necessary to open the System System and Safety Point Settings.

Next, go to the additional setting.

Switch to the tab with the name of the car and run the process of inclusion in the group.

A special master will open, in which you need to consistently indicate:

To complete the operation, a reboot of PC will be required.

Change to private profile

If the previous actions worked correctly and the computer from Windows 10 was displayed in the network environment, another machine sees it, but it doesn’t work out and open it. It is probably the wrong network profile is applied. In this case, system settings prohibit its detection.

It is necessary in the parameters to open the subparagraph “Network and the Internet” and go to view the condition.

Scroll the list to the subparagraph dedicated to the home group.

The next step, run the location on the network. The system will request confirmation for the approval of the detection by third parties that are connected to the LALL. You need to agree, otherwise it will not work to fix it.

After that, repeat the viewing of the network. Normally, the machine should be visible and affordable.

Cannot see other computers in My Network Places?

Reset parameters

If the computer does not see another car in the home network, you can drop the connection parameters. This is done on the same network page.

computer, does, other, computers

Also return the firewall settings to the original state. To do this, use the NETSH utility three times from the team building, adding such parameters through the gap and sending everyone to execute Enter’om:

How to configure TCP/IP parameters

If the problem is not in the driver, you need to study the main software settings that affect the Internet connection. It is necessary to check whether the necessary protocols are activated, and how the receipt of the IP address and DNS work.

computer, does, other, computers

Checking activated network protocols

For the normal operation of the Internet, it is necessary that the main protocol IPV4 is activated. In addition, it is worth trying to turn on and off the IPV6 protocol-in some situations, a network connection can behave unpredictably precisely because of it.

Checking the IP address and DNS settings

If the activation or deactivation of protocols did not help, it is worth checking the IP and DNS settings.

  • Click Win R. Enter the NCPA command.CPL and click Enter.
  • Find the desired network adapter, click on it with the right mouse key and select the properties.
  • Click on the IP version 4 (TCP/IPV4) and click on the Property button.

If this does not solve the problem, you should try to change the DNS address to GOOGLE. Quite often it helps.

  • Put a checkplace use the following DNS servers addresses.
  • Enter in the field preferred DNS server numbers 8.Eight.Eight.Eight.
  • Enter alternative DNS server numbers 8 in the field.Eight.4.4.

After all these operations, it is worth rebooting the computer to check whether they helped or not.

FIPS standard setting up

Sometimes the FIPS (Federal Information Processing Standards or Federal Information Standards) can help to turn on or shut off the FIPS standard. It was created for US government institutions, but computers are available in any region.

Denial of responsibility | Contacts |RSS | SE | EN | BR | DE