Samsung

Samsung machine error 3 e

Drum load exceeded

Power drive failure can occur due to excessive weight of the laundry loaded into the drum. For example, Diamond series machines are designed for 6 kg of items, when an additional 500-700 g is piled, the equipment is turned off. The manufacturer has installed an overload protection because the drum with an increased mass breaks the bearing arrangements. In addition, the body and electronics of the machine may be destroyed due to the increased level of vibration. With slight overloads, overheating of the motor windings is possible, which triggers the bimetallic fuse.

samsung, machine, error

The owner needs to turn off the equipment, remove the water through the emergency drain, and then remove some of the laundry from the drum cavity. If the error does not appear when the wash cycle is restarted, the cause of the malfunction is overload. If the warning light comes on, a power actuator and electronics check is required.

Tachogenerator malfunction

A common reason for the 3E error in Samsung washing machines is a sensor that determines the number of revolutions of the electric motor rotor (tachometer, or Hall sensor). Electronic components are out of order or the sensing element on the motor shaft (magnetic ring) becomes dirty. In this case, the machine can wash laundry; when you try to turn on the spin, the motor stops and the code is displayed on the screen. The equipment cannot work without a sensor, which limits the frequency of rotation of parts and prevents the destruction of the machine from vibrations.

If excessive or insufficient rotation of the drum occurs, then the cause of the defect is the weakened fastening of the ring to the rotor shaft. To restore operability, it is required to disconnect the equipment from the water supply and drain lines, and then get to the engine. The magnetic ring is fastened with a screw, when the tightening is loosened, the element slips. It is recommended to clean the outer surface from dirt and oxides, which impair the reading of information by the sensor.

Sensor problems can arise from oxidized or broken wires connecting the sensor to the electronic components of the machine. The cables are checked with a test device in the dial mode or with a control lamp. It is recommended to connect the tester, and then move the wire by hand (the defect may be floating and appear when the machine is in operation). The damaged sections of the cables must be replaced, but it is recommended to install a new harness. Contacts are cleaned from oxidation traces, damaged elements must be re-soldered.

If the error code appears again, then a check of the electronics in the service conditions is required. The device checks the circuit going from the sensing element to the control controller. The cause of the defect may be a burnt out diode (the defect is not visually detected). The problem may arise due to an incorrectly operating electric heater (TEN), which is recommended to be inspected and checked with a tester. The combination of a burnt out diode and a damaged heating element is noted in Samsung Eco Bubble washing machines.

How to fix error 3E on a Samsung washing machine by yourself

The 3E error that appears during the operation of the Samsung washing machine indicates an incorrect determination of the speed of the rotor of the electric motor. Does the control controller receive an erroneous feedback signal, which leads to the interruption of the washing process? The owner can independently check the operation of the AGR units and eliminate the faults found.

Motor problems

In a Samsung washing machine, the 3E error is displayed on the LCD. On equipment manufactured after 2013, codes like 8Ex or 8Cx (where x is an Arabic numeral) may appear on the screen, which indicate similar problems. In older versions that are not equipped with a display, the code is transmitted by constant switching on of the LEDs for the standard wash modes at 40 ° С and Bio 60 ° С, while the orange indicators are blinking.

The equipment may display an error code after filling with water, but when trying to start, an error code 3E is displayed. This symptom may mean a short circuit or an open circuit in the winding of the electric motor. The owner must manually drain the drum or try to drain the water with a standard pump (by forcibly turning on the drain mode). For manual removal, a branch pipe with a filter element located in the lower part of the housing is used. The liquid is drained in portions into a flat tray or removed with hygroscopic material.

At home, the user can remove the engine, which is located under the drum. The motor is fastened with bolts and nuts, if there is a test device, then the condition of the insulators can be checked. Breakdown of the windings on the case is not allowed, you can also disassemble the motor and find damaged turns.

The motor needs to be repaired (rewound) in a specialized service, if restoration is not possible, then you will need to purchase a new unit (supplied by Samsung as a spare part).

If a malfunction appears during the washing process, then it is necessary to check the condition of the brushes. When the graphite elements are worn or damaged, sparking occurs in the collector, which leads to a decrease in engine power. When installing new brushes, it is recommended to inspect the collector; if mechanical damage is found, it is necessary to send the engine to a repair shop.

Loose drive belt

To transfer torque from the rotor of the electric motor to the drum, a belt drive is used. To increase the efficiency of work, a poly V-belt is used, which has an increased resource. There is no automatic tension of the drive, therefore, with natural aging of the material, the belt begins to slip. As a result, the screen displays the code 3E or 8E (depending on the year of manufacture of the equipment), the problem manifests itself at the beginning of the washing process or when the drum is accelerated during the spinning procedure.

To access the belt drive, you must:

  • Switch off the power supply and then disconnect the connection hoses.
  • Unscrew the screws holding the back cover on the machine body.
  • Inspect the belt; no scuffs or cracks are allowed on the treadmill. It is also possible for the elastic element to delaminate or damage to the pulleys. Defective parts need to be replaced, and then check the machine.

A screw puller for rolling bearings is used to dismantle the pulleys. The small-sized pulley on the rotor is removed after several heating cycles, since a special solution is applied to the joint line to fix the parts. Do not install a new belt on damaged pulleys as sharp metal edges will destroy the treadmill. It should be remembered that in part of Samsung machines, a direct drive motor is used, the belt is removed from the kinematic chain.

Control Unit problems

If the equipment turns off at the start of washing, then the cause of the defect may be the control unit located in the upper part of the case. The controller contains electronic components that can come loose from the contact tracks or fail due to vibration or moisture. Employees of service centers note poor soldering of electronics and low quality of printed circuit boards, from which the metal substrate peels off.

The block is checked in the service conditions. The user cannot find microcracks in the elements or determine an incorrectly operating diode or transistor. Removing damaged parts and installing new parts requires special soldering equipment. Fatally damaged controller must be replaced.

Samsung washing machine error 3

On Samsung washing machines, error 3e is not encountered as often as all others, but, nevertheless, it can create a lot of difficulties for the user, who suddenly loses his “home assistant” at the moment when he so needs it. When this error appears, like all other errors, the washing stops and does not resume until the cause that caused the problem is eliminated. Let’s get down to establishing the causes of error 3e, and at the same time decipher it.

The moment of appearance of the code and its analogues

Error 3e rarely appears spontaneously. often it “jumps out” at certain stages of the washing program, showing a certain pattern. Imagine a Samsung washing machine starts washing your laundry. Water is collected, the drum gradually begins to spin and suddenly, there is a freeze, the machine stops the rotation of the drum and at the same minute an error 3e appears on the display. It happens in a different way.

  • You are starting a washing program on a Samsung automatic washing machine.
  • The machine draws in water and performs the wash.
  • Next, the washing machine drains the dirty water, draws clean water for rinsing and starts rinsing.
  • This should be followed by a spinning step, but spinning does not occur. The machine, having slightly spun the drum, freezes, giving an error with code 3e.

After rinsing, the machine tries to spin the drum to a more or less decent speed, but this does not happen.

If you are faced exactly with the above symptoms, but a different code is displayed on the display, remember that error 3e has analogues with a similar decoding. It may very well be that you will come across codes: 3C, 8E, EA, 3e1, 3e2, 3e3, 3e4, 3c1, 3c2, 3c3, 3c4, 8e1, 8c, 8c1. Quite a lot of analogs, it is easy to make mistakes, so be careful. EA code is typical for washers that came out before 2008, but codes 8E, 8e1, 8c, 8c1 are typical for washers younger than 2013.

Another question arises: how does error code 3e appear on Samsung washing machines that do not have a display? In the picture below you will see the answer to it. When such an error occurs, two lamps 40 0 ​​C light up on the display, and then Bio 60 0 C. But that’s not all, the indicators indicating the washing programs will start blinking quickly.

How it stands?

As always, let’s start by literally deciphering error 3e. It means a problem with the tachometer or the engine. Such a lengthy description of the error can hardly suit us, so we will try to decipher it in more detail. First of all, we will decipher the twin errors that are found on some models of Samsung washing machines instead of code 3e.

  • The error with the EA code is deciphered in exactly the same way as 3e, just this code was used on older models of Samsung washing machines, however, we already talked about this above.
  • Codes 8e, 8c, 8c1 mean problems with the vibration sensor, which is installed on the most modern models of washing machines.

A vibration sensor is a device that allows you to control the movement of the drum in different planes, while a conventional tachometer is only able to control its revolutions.

  • Error 8e1 indicates serious malfunctions in engine control, in fact, a complete loss of communication with a vibration or tacho sensor.
  • Well, errors of the 3C series may appear due to the loss of engine power of the Samsung washing machine.

Why does the code appear?

Conventionally, the problems that this error “symbolizes” can be divided into two categories. The first category includes malfunctions that do not lead to breakage of parts and assemblies of the Samsung washing machine, and the second category includes more serious breakdowns that give rise to the need to carry out serious repairs to the “home assistant”. So let’s start with simple troubleshooting.

At first glance, it may seem ridiculous, but such banal things as overloading the drum with laundry can lead to an error with code 3e or 3C. If you put too little laundry, a 3C error may appear. These codes can also symbolize drum jamming due to foreign objects falling between the tank and the drum if the engine does not have enough power to overcome the jam. Any of the above errors can pop up due to a short-term failure in the self-diagnosis system, and if so, you are very lucky. nothing needs to be fixed.

Let’s move on to the second category of faults. Error 3e may result from the complete combustion of the tachometer and a complete break in communication with it. If a Samsung washing machine has a vibration sensor instead of a tacho sensor, similar troubles may arise with it. Not everything is going smoothly with the engine either. When an error 3C appears, one can judge the loss of engine power due to worn brushes or a broken winding.

The tachometer may give incorrect signals due to oxidation of the magnetic ring or the motor shaft. Also, dirt gets between the motor shaft and the tacho sensor ring, which causes the same problems. Weakening of the tachometer signal, or its periodic disappearance may be due to poor attachment of this sensor to the engine, all this can also generate an error with code 3e.

One of the rarest causes of error 3e and its analogs is a loose drive belt. Due to a similar problem, the engine cannot pick up speed and spin the drum, which is sometimes perceived by the self-diagnosis system of the washing machine as a problem with the motor, which is why it issues code 3e.

As you can see, there are quite a few cases of the appearance of code 3e and its analogues, so be extremely careful not to confuse anything, this will drag out the troubleshooting time.

Eliminate the reasons

Well, we have listed the reasons for the error 3e of the Samsung washing machine, now let’s figure out how to fix them. Let’s go in order.

  • If you managed not to report things to the drum of the washing machine or, on the contrary, overload it and this led to error 3e, you will fix it yourself. Unplug the machine from the mains, take out unnecessary items or add additional items if they are not enough, and then start the washer again. the problem will be solved.
  • Drum jamming is worse. If a foreign object gets into the tank, you will have to remove it through the hole for the heating element, and in order to remove the heating element, you will have to remove the front wall of the Samsung washing machine. How best to do this is described in the article. Samsung washing machine throws HE2 error. As soon as you manage to remove the teng, you can put your hand into the hole and take out from the bottom of the tank what accidentally got there.
  • In case of a short-term malfunction of the washing machine, you just need to restart it, disconnect it from the mains for 5 minutes, and then turn it on again. Error 3e or similar should be gone.
  • If the tachometer burns out, it must be replaced with a new one of the same type. We unscrew the back wall of the washer, remove the drive belt so that it does not interfere, remove the wiring from the engine and unscrew it. We remove the old tachometer from the motor and install a new one.

Check the part with a multimeter to make sure the part is defective.

  • For a motor that has lost power, the brushes must be checked and replaced. There are small screws on the sides of the body that you need to unscrew to remove the spring-loaded graphite rods. They are called brushes because they rub against the moving part of the commutator motor and can wear off. If this happened with at least one brush, we change both at once.
  • We treat the breakage of communication with the tachometer by detailed checking and cleaning of this element. It is necessary to thoroughly clean the inner magnetic ring from oxide and dirt, after which the contact will be restored. Along the way, we also check the integrity of the wire supplying the sensor and its contact.
  • If you still encounter a 3e error, which is caused by a weakened drive belt, you need to replace such a belt immediately. It is unacceptable to continue using the washing machine with such a belt. Read about how this part is replaced in the article. How to put a belt on a washing machine?

Стиральная машина Samsung eco bubble WF702W2BBWQ ошибка 3E

Summing up, we note that error 3e is not only multifaceted in itself, but it still has many analogs that are not always deciphered in the same way. To understand all this in more or less detail, read the publication again, and we wish you good luck and patience.!

When Code 3E Occurs

The 3E code has analogues that have a similar decoding. They are the following error codes: 3E1, 3E2, 3E3, 3E4, 3C, 3C1, 3C2, 3C3, 3C4, EA, 8E, 8E1, 8C, 8C1. The emergence of EA is typical for Samsung washing machines before 2008 production. And codes 8E, 8E1, 8C, 8C1 are found in washing machines until 2013.

If your typewriter does not have a display, then pay attention to the lit lamps: BIO 60 ° C and 40 ° C. The mode indicators are blinking.

Rarely, a Samsung washing machine generates a 3E error just like that. most often such a code appears at specific stages of the wash, which means a certain pattern. The washing machine gives a problem when the code 3E, 3E1, 3E2, 3E3, 3E4, 3C, 3C1, 3C2, 3C3, 3C4 is on, when:

  • Spinning the drum at the start of the program;
  • Rinsing linen;
  • Spin, when the machine spins the drum a little and displays 3E.

What is the reason for the error

The car may show error 3E when:

  • Excessive loading of the drum with things;
  • Foreign objects falling between the tank and the drum;
  • Temporary failure in the control module;
  • Failure of the tachometer;
  • Failure of the vibration sensor;
  • Weakening of the drive belt;
  • Decrease in engine power, which is possible due to worn brushes or a punctured winding;
  • Control module malfunctions.

Error 3E, 3C, EA in Samsung washing machine

When a 3E error appears on the display, washing stops and does not resume until the malfunction code is cleared. And in order to find out what error 3E means and what to do to eliminate it, you need to determine when it occurs and for what reason.

This code corresponds to a tachometer error. weak or absent signal. Most often, to eliminate it, you need to call the wizard.

What does the error mean

If the Samsung SMA display shows 3E, 8E, EA, then most often this indicates a malfunction in the tachometer or engine. Analogs of the 3E code are deciphered as follows:

  • EA is similar to the 3E code, it is simply displayed on the display of early models of Samsung typewriters;
  • Error 3E1, 3E2, 3E3, 3E4, 3C, 3C1, 3C2, 3C3, 3C4 also indicates a malfunction of the tachogenerator;
  • Code 8E, 8C, 8C1 indicates problems in the vibration sensor, which is present in modern models of Samsung washing machines;
  • 3C indicates that the power of the washing machine motor is reduced.

To solve this problem, you need to understand the reasons for the display of the 3E code and its “brothers”.

How to fix the problem

After analyzing the reasons for the error codes popping up on the display of the washing machine, it is important to learn how to fix the malfunction on your own. Here’s what you need to do to clear the error:

  • If the washing machine is overloaded, turn it off and remove excess laundry. Then start the machine again.
  • If the drum is jammed, remove the foreign object through the hole for the heating element. To get the heating element, you will need to remove the front wall of the washing machine.
  • In case of a temporary control failure, turn off the machine by unplugging the power cord for a few minutes, and then turn it on again.
  • Replace the burnt-out tachometer with a new one.
  • Check the motor brushes and replace them if necessary.
  • If the connection with the tachometer is broken, check and clean the element.
  • Replace this element if the drive belt is loose.
  • In the event of a malfunction of the control module, solder the burned-out elements on the board or completely replace the module.

Now you know how to fix problems in a Samsung typewriter. most often you need to involve a specialist in this case, who will fix problems in the engine or tachogenerator. But in the first three cases, you can deal with the problem yourself.

Decoding the code

Error E9 is typical for Samsung washers assembled before 2007. Accordingly, the service life of this equipment today is 8-10 years, it is not surprising that users have begun to contact service centers with a similar problem more often.

What does the E9 code mean? This code indicates that the machine has leaked water from the tank to the sump. If the pressure switch detects 4 times a drop of water in the tank, the machine will stop working, and the display will show the code E9.

Please note that in modern models of Samsung typewriters, instead of the E9 code, the L9 code is embedded in the program memory. These are identical codes.

However, in new machines, not only the pressure switch reacts to water leakage, but also the Aqua stop sensor installed in the pan. These error codes can appear on any wash cycle. But most often, the error is displayed almost immediately after turning on the program, or during the first set of water.

Old washing machines do not have a display, so a breakdown is signaled by flashing indicators. All lamps for washing modes blink when water leaks, but indicators Bio wash 60 0 С and cold water are on.

Causes of occurrence

Different reasons can lead to error E9 or L9. Some malfunctions can be eliminated by hand, in other cases the help of experienced specialists will be required. First of all, you need to check the following:

  • the tightness of the connection of the water drain hose to the sewage system and the hose itself for breaks; in the case of draining water into the bathroom or toilet, see if the hose is ripped off, if water is flowing past;
  • correct connection of the drain hose to the sewer pipe, if the level of the hose is violated, then the water will spontaneously pour out of the tank;
  • the tightness of the installation of the drain filter, in the event that you pulled it out the day before for cleaning;
  • pay attention to whether water is flowing from the powder tray, if the holes for filling water into the tray are clogged, then the water will not flow into the tank, it will flow out;
  • after external inspection, proceed to inspect the “insides” of the washer, check the pipe from the tank to the pump and from the powder receiver to the tank, maybe there is a need to replace the clamps that hold the pipes;
  • check the contacts of the electrical wires going to the water level sensor and to the Aqua stop.

If an E9 error appears in a Samsung washing machine or any other, you can try to restart the washing machine, so to speak, reset the program. There may have been some kind of glitch that caused the error to appear. You can reset everything by unplugging the machine from the outlet for a few minutes.

serious reasons are caused by breakage and malfunction of the part, in this case, these are:

  • Aquastop sensor;
  • rubber cuff;
  • hose and pipes;
  • pressure switch;
  • wiring and electronic module.

Replacing the cuff and pipes

Replacing the cuff in any brand of washing machine is more time consuming than replacing the sensors. After all, in order to remove and put on an elastic band, you need to disassemble the body of the machine. Some experts, having the skills, can replace the cuff on a Samsung washing machine by removing only the top cover, but those who do it for the first time may not get this “trick”.

How to disassemble the washer and replace the rubber band, we described in detail in the article How to change the cuff in a washing machine, so we decided not to repeat ourselves.

As for the branch pipe, most often the branch pipe connecting the pump and the tank breaks. This part is replaced through the bottom. It is either missing or easily removable. The branch pipe is held in place with clamps, which will also need to be replaced.

Samsung washing machine error E9

Thanks to the self-diagnosis system of the Samsung washing machine, in the event of a breakdown, you can reduce the time for repairs. An error that appears on the machine display notifies the user of what has happened. It is important to know the decryption of the code and the possible reasons for its appearance. Let’s talk more about the E9 error in the Samsung washing machine.

Change sensors

First, we will describe the replacement of the Aquastop sensor, this part is also called a microswitch with a float. It is located, as we have already noted, in the tray of the washing machine. Therefore, to replace it, it is necessary to disconnect the equipment from communications, pull it out to a convenient place and put it on its side. Then we do this:

  • unscrew the pallet;
  • carefully remove the pallet from the car, do not shade it sharply, so as not to tear off the wires coming from the sensor;
  • disconnect the chips with wires;
  • detach the latches and take out the sensor;
  • replace the faulty part with a new one.

The water level sensor, which is called a pressure switch, is, on the contrary, located at the top of the washing machine. You can also replace it yourself, spending 20 minutes on work. To do this, disconnect the machine from the network, close the water supply tap, and then follow the instructions:

  • unscrewing the rear bolts, remove the upper case cover;
  • in the upper corner of the machine find a part as in the photo below;
  • disconnect the chip with wires;
  • unclench the clamp and remove the air supply tube;

Important! pay attention to the air duct, it may be the case, very often the tube breaks through at the base of the pressure switch, so the sensor cannot accurately measure the water level. It is enough to replace the tube and the problem will be solved.

What to do with the electronic module

The electronic module is not only the most expensive part in a washing machine, but also requires special knowledge during installation and especially during repair. If the processor on the control board is not burnt out, it can be repaired. Otherwise, the board will need to be completely changed.

When replacing an electronic module, there is such a nuance as firmware; some boards do not have software installed. To install it, you must first find it, and then carry out the process correctly. It is for this reason that we recommend contacting specialists and not taking responsibility for yourself. Perhaps, having learned the cost of a part and repair, you might even think about buying a new machine, because everything will cost a lot.

Thus, there are many reasons for the appearance of the E9 error. Most of them require the skills of repairing and disassembling the washing machine. We hope our article will help you determine the trajectory of actions in this situation. Good luck!

Probable causes of malfunction requiring professional repair

As the masters note, in Samsung washing machines, error 3e is one of the most common, like the same 8e and EA. But they recommend not to fix it on your own, but immediately contact the master or the service center if the unit is still under warranty.

  • If the machine picks up water during operation, makes several revolutions of the drum, and, after stopping, gives an error, then a possible malfunction lies in the breakdown of the tacho sensor (Hall sensor). In this case, the master changes the Hall sensor itself.
  • The machine works as usual, and when you try to change the washing program, error 3e, or EA or 8e appears on the display, and so on. The reason for such a breakdown may lie in oxidation, the subsequent weakening of the contact of the magnetic ring of the tachogenerator, as well as the surface of the shaft in the structure of the engine. In this case, a complete replacement of each surface of the tachogenerator unit and the engine shaft is performed.
  • An equally frequent problem that owners of Samsung washing machines may encounter is that the washing goes well, but after that the laundry is not wrung out. Often after that, an error 3e or 3c appears on the display of the unit, like EA or 8e. As the masters note, the first thing to do is to check the mount, which can unwind during operation, causing the equipment to fail.
  • The washing machine collects water before starting work and at the same time after starting it does not turn the drum. no matter what program is installed, an error on 3e or another will be displayed on the display. In this case, experts talk about a malfunction in the engine of the unit. Most often they talk about a winding break or a direct short circuit. The malfunction of the winding itself in the electric motor is eliminated by many owners of the units by rewinding in the place where the integrity of the motor is broken. But, as practice shows, this is an ineffective solution to the problem, since it is required to completely change the motor itself.
  • If the CMA stops, and then gives an error 3e or EA, like 8e, 2-5 minutes after starting the wash, the subsequent spinning, when the unit is gaining speed. In this case, the masters talk about problems with the engine itself. the drive belt has stretched, flew off or stratified. This problem will be indicated by jerks and “overshoots” in the engine during the washing process, and the tachometer sees this malfunction and knocks it out on the display. The solution to this malfunction is simple. the craftsmen can simply change the belt in the drive system. Another reason for the error in this case may be the wear of the brushes of the electric motor. in this case, the electronic field they create will simply not be enough for a full wash and a set of revolutions. The solution to this breakdown is simple and quick. a complete replacement of worn brushes, which can be done at home.
  • Some owners of Samsung brand washing machines may encounter a situation in which the drum spins after filling with water, and then displays an error code 3e on the display, like EA or 8e. Such an error can occur at any stage of starting and operating the unit: at the stage of washing, rinsing and spinning the laundry. Most often, experts call the cause of such a breakdown an open circuit in the tachogenerator circuit. this may be a wire damage or a short circuit, as well as a breakdown of contacts. The solution to the problem is to restore the broken integrity of the wire itself, or to completely replace the loop. The place of the broken contact is re-soldered, the weak contacts are cleaned, and then tightened.
  • Often the CMA turns off after the start of washing or rinsing, spinning and the display shows error 3e. In this case, the masters talk about a malfunction in the control module itself. The signal coming from it disappears. Most often, the reason for such a breakdown is a break in the track of the electronic board. Perhaps, the elements of the system simply shorted or burned out. a relay, resistance, diodes or a capacitor, which are responsible for the speed, rotation of the engine during operation, as well as communication with the tachogenerator. How to fix the breakage in this case? A simply burnt out and out of order element of the system, be it a relay or a diode, is changed to a new one. If the system module itself came out of standing, it is changed to a new one and such work is carried out exclusively by a master who has certain skills and knowledge.

Even if you could not correct the error 3e, EA or 8e issued on the display, do not despair. The main thing is not to try to eliminate it yourself, without having the necessary knowledge and experience. The best solution is to invite a master. And if the unit is under warranty, then the best option would be to give it to a service center.

Almost all washing machines have been equipped with an artificial intelligent ability to recognize many of their faults for more than a decade. Malfunctions occur for various reasons in technology. There is normal wear and tear of parts and assemblies, there are breakdowns caused by improper operation of the device.

Also, malfunctions can arise from the places and conditions of use of the devices. In the event of a partial or complete breakdown of a part, the product processor recognizes a failure in the full operation of the product and turns it off. In this case, the machine displays the code of the malfunction that has occurred. On older models, the code appears in the form of a certain combination of illuminated LEDs.

On new models, everything is much simpler, the existing display shows a code in the form of symbols. One of the combinations of such symbols is the 3E error in Samsung washing machines. To repair a Samsung washing machine with error 3E, you need to understand what exactly is out of order.

Why does error code 3e appear

Error 3E on a Samsung washing machine appears during its operation due to malfunctions in its design or control. It should be noted that the fault codes do not necessarily indicate a specific part or assembly. An error code indicates a lack of any missing or poorly performed product function.

Before headlong barbaric disassembly of the device, relying on the first words from the decoding of the error code 3E of the Samsung washing machine, you must thoroughly read the entire description of the possible causes of the malaise of the product of this brand. In fact, the code may indicate malfunctions of several nodes.

Our task is to correctly identify the one that is the cause of the error 3E of the Samsung washing machine. Any repair of equipment should begin with diagnostics and identification of the part that needs replacement. By the method of trial replacement of parts, it is far from always possible to even establish the causes of the breakdown, because there may be several parts that have come out.

In this case, we change one, then another and further subsequent ones, but there is no result. And so many necessary new parts are unlikely to be at hand. It is necessary to understand the occurrence of error 3E in the Samsung washing machine in more depth. You need to understand why it occurs and what to do if the Samsung washing machine gives an error 3E.

It is also necessary to check in order all the parts and assemblies to which this code points. This process is not so easy, but the microprocessor has already solved half of the problem for us. He pointed out to us possible malfunctions or the reasons why error 3E appeared on the Samsung washing machine.

How it stands?

On different models of machines from this manufacturer, the 3E error appears in different ways. On models without a display. by flashing a certain combination of LEDs. On products with a display, a code appears in the form of symbols. When symbols or LEDs light up on the panel or display, the washing machine stops the program and drains the water.

In the Samsung washing machine, error 3E may indicate that the electronic module is not able, for some reason, to determine the operation of the washing machine engine. It happens something like this: the electronics controls the required engine speed by increasing the current to it.

And, if the frequency of the required revolutions does not match the supplied current, the processor sounds the alarm and turns off the machine. A system for recognizing faults has been invented so that the resulting breakdowns do not entail a number of others. And undoubtedly, this function has simplified the tasks of the repairers of such equipment.

Код ошибки стиральной машины Samsung 3E не вращается и не вращается

Several reasons for the appearance:

  • The drive motor is blocked by foreign objects. Often this occurs due to seized bearings both in the engine itself and in the tank of the washing machine;
  • Full or partial loss of contacts in the power supply of the engine or its control system. Most often this occurs due to the use of the device in damp places. The module receives an incorrect signal and turns off the product, all this is accompanied by an emergency drain of water;
  • The tachogenerator is defective. The tachometer measures the rotor speed and in the absence of signals from it, a malfunction occurs and the machine issues a code;
  • Drum loading with items exceeded. Users are accustomed to understanding that it is possible to load the washing machine to the maximum allowable level, without taking into account that each type of fabric has a different absorbency. By feeding 5 kg of water, the laundry can turn into a rather heavy mass. The engine can turn the drum only with great effort. Signals to the module are received incorrectly, and the engine itself is overheating. The program also reports a malfunction with code 3E;
  • Newly purchased washers may have a malfunction caused by improper motor assembly. It can also be caused after the current repair of the motor;
  • Looseness of the drive belt;
  • Engine malfunction due to heavy loads;
  • The Control Unit may be malfunctioning. Electronics is a fairly reliable thing, but under conditions of correct use. Malfunctions in it occur due to power surges, moisture ingress on its components. It also fails when the operation of the washing machine is not carried out in accordance with the manufacturer’s standards. In many models of Samsung washing machines, the components of the control unit are filled with a special substance, protecting them from moisture. But this does not mean that the entire device is so protected and can be used in high humidity indoors. It can be unsafe for the owners of the product.

Decoding the error

Codes 3E, 3E1, 3E2, 3E3, 3E4, 3C, 3C1, 3C2, 3C3, 3C4, EA on a Samsung washing machine mean an error in the tachometer (Hall sensor) of the engine. The control module receives an incorrect or too weak signal from the sensor, or the tacho is simply “silent”. Therefore, the “control brain” stops the engine. And the Samsung machine informs you about the problem with the code 3 E, EA, 3C, etc.

Note! In the new generation CMA, with such a malfunction, a group of codes 8E / 8E1 / 8C / 8C1 is displayed, which mean an error in the VRT vibration sensor. This is a new improved tachometer that can control both engine speed and three-dimensional drum vibrations.

Most often, the EA / 3 E / 8E error on a Samsung washing machine indicates significant motor control failures. But sometimes it is possible to eliminate the cause of the appearance of the code without calling the wizard.

The moment this code appears

Quite often, the error code 3e itself appears randomly. Most often, an error occurs at a certain stage in the operation of the unit, whether it be washing or spinning. In this case, the machine will collect, as expected, water, the drum begins to spin and suddenly. the CMA freezes and shows this system error.

Как исправить ошибку стиральной машины Samsung 3E

  • The washing program starts.
  • The unit draws in water and washes.
  • Then it drains the water and collects clean water for subsequent rinsing.
  • Next, there should be a spin, but instead, the system simply freezes and displays an error on the display.

To fix the problem and understand whether the breakdown is subject to repair or not, it is important to understand what this code means.

What does this code mean?

If we talk about what the error in the 3e format that appears on the display of the washing machine means. many masters say that a number of breakdowns can provoke it. At the very beginning, a breakdown can mean a problem with the tachometer or the engine itself. Such a decoding is unlikely to help you decide on the question of what to do with the washing machine and whether it needs to be repaired.

Next, we will consider the main interpretations and decoding of the error in the operation of the Samsung washing machine with code 3e.

The error knocked out on the display with the code abbreviation EA in modern models released after 2008 is deciphered in the same way as the code 3e. Therefore, these designations are considered equivalent.

Code 8e and 8c, like 8c1, indicates a breakdown, a malfunction of the vibration sensor in the unit. it allows you to control the intensity and speed, movement in the drum unit in its different planes.

An error with code 8e1 knocked out on the washing machine display indicates a failure directly in the operation of the electronic engine control and, in essence, is associated with a vibration sensor or a tachometer.

Also, breakdowns can be a consequence of losses, a decrease in the power of the engine itself.

The breakdowns themselves can be conditionally divided into 2 groups. those that are not provoked by the breakdown of parts, machine units and assemblies, and they can often be eliminated on their own. The second group includes more serious breakdowns and requires the intervention of specialists. Among the common reasons that lead to error 3e or 3C, the masters include:

  • overloading the drum of the washing machine with things.
  • getting through the fault of the manufacturer or the user himself into the space between the drum and the tank of a foreign object.
  • failure in the very operation and settings of the control module, as well as the vibration sensor and the tachometer.
  • a decrease in the engine power level, provoked by wear of the brushes, or a punctured winding.

Although the most common reason that the display of a Samsung washing machine knocks out this error, the masters call it the weakening of the tension of the drive belt.

What error 3E means on a Samsung washing machine: troubleshooting

Almost all washing machines have been equipped with an artificial intelligent ability to recognize many of their faults for more than a decade. Malfunctions occur for various reasons in technology. There is normal wear and tear of parts and assemblies, there are breakdowns caused by improper operation of the device.

Also, malfunctions can arise from the places and conditions of use of the devices. In the event of a partial or complete breakdown of a part, the product processor recognizes a failure in the full operation of the product and turns it off. At the same time, the code of the malfunction that has occurred is given on the display of the machine.

On older models, the code appears in the form of a certain combination of illuminated LEDs.

On new models, everything is much simpler, the existing display shows a code in the form of symbols. One of the combinations of such symbols is the 3E error in Samsung washing machines. To repair a Samsung washing machine with error 3E, you need to understand what exactly is out of order.

Why does error code 3e appear

Error 3E on a Samsung washing machine appears during its operation due to malfunctions in its design or control. It should be noted that the fault codes do not necessarily indicate a specific part or assembly. An error code indicates a lack of any missing or poorly performed product function.

Before headlong barbaric disassembly of the device, relying on the first words from the decoding of the error code 3E of the Samsung washing machine, you must thoroughly read the entire description of the possible causes of the malaise of the product of this brand.

In fact, the code may indicate malfunctions of several nodes.

Our task is to correctly identify the one that is the cause of the error 3E of the Samsung washing machine. Any repair of equipment should begin with diagnostics and identification of the part that needs replacement. By the method of trial replacement of parts, it is far from always possible to even establish the causes of the breakdown, because there may be several parts that have come out.

In this case, we change one, then another and further subsequent ones, but there is no result. And so many necessary new parts are unlikely to be at hand. It is necessary to understand the occurrence of error 3E in the Samsung washing machine in more depth.

You need to understand why it occurs and what to do if the Samsung washing machine gives an error 3E.

It is also necessary to check in order all the parts and assemblies to which this code points. This process is not so easy, but the microprocessor has already solved half of the problem for us. He pointed out to us possible malfunctions or the reasons why error 3E appeared on the Samsung washing machine.

How it stands

On different models of machines from this manufacturer, the 3E error appears in different ways. On models without a display. by flashing a certain combination of LEDs. On products with a display, a code appears in the form of symbols. When symbols or LEDs light up on the panel or display, the washing machine stops the program and drains the water.

In the Samsung washing machine, error 3E may indicate that the electronic module is not able, for some reason, to determine the operation of the washing machine engine. It happens something like this: the electronics controls the required engine speed by increasing the current to it.

And, if the frequency of the required revolutions does not match the supplied current, the processor sounds the alarm and turns off the machine. A system for recognizing faults has been invented so that the resulting breakdowns do not entail a number of others. And undoubtedly, this function has simplified the tasks of the repairers of such equipment.

  • The drive motor is blocked by foreign objects. Often this occurs due to seized bearings both in the engine itself and in the tank of the washing machine;
  • Full or partial loss of contacts in the power supply of the engine or its control system. Most often this occurs due to the use of the device in damp places. The module receives an incorrect signal and turns off the product, all this is accompanied by an emergency drain of water;
  • The tachogenerator is defective. The tachometer measures the rotor speed and in the absence of signals from it, a malfunction occurs and the machine issues a code;
  • Drum loading with items exceeded. Users are accustomed to understanding that it is possible to load the washing machine to the maximum allowable level, without taking into account that each type of fabric has a different absorbency. By feeding 5 kg of water, the laundry can turn into a rather heavy mass. The engine can turn the drum only with great effort. Signals to the module are received incorrectly, and the engine itself is overheating. The program also reports a malfunction with code 3E;
  • Newly purchased washers may have a malfunction caused by improper motor assembly. It can also be caused after the current repair of the motor;
  • Looseness of the drive belt;
  • Engine malfunction due to heavy loads;
  • The Control Unit may be malfunctioning. Electronics is a fairly reliable thing, but under conditions of correct use. Malfunctions in it occur due to power surges, moisture ingress on its components. It also fails when the operation of the washing machine is not carried out in accordance with the manufacturer’s standards. In many models of Samsung washing machines, the components of the control unit are filled with a special substance, protecting them from moisture. But this does not mean that the entire device is so protected and can be used in high humidity indoors. It can be unsafe for the owners of the product.

How to fix error 3E on a Samsung washing machine

If, as a result of inspection and diagnostics of each possible unit, we have identified a faulty one, then you can cope with its repair or replacement yourself or resort to assistance in repairing equipment by a specialist. Everyone decides what to do in this situation.

But if you decide to cope on your own, then below are written options for eliminating various causes of error code 3E:

  • If a foreign object gets into the engine or tank of the washing machine, remove it. Often, when washing, personal belongings of their owners fall out of the s of things, buttons, zippers fall off. Before washing, you should carefully examine the s and the reliability of fastening accessories to things. Seizure of bearings is always accompanied by their hum during operation for a long time. At the first extraneous noise of the machine, measures must be taken to prevent further damage;
  • Contact problems can be resolved by restoring them. To do this, most often it is enough to clean them from oxidations and other impurities. But in frequent cases, it is necessary to repair the power outlet and wiring;
  • A faulty tachogenerator cannot be repaired, it must be replaced;
  • If the reason is an excessive load of laundry, you need to partially free the drum from it and start washing again.
  • The reason for the incorrect assembly of the engine in a new washing machine should be eliminated by warranty services, you should not climb yourself. over, it will be done for free. Well, if current repairs influenced the appearance of code 3E, then it is necessary to re-sort the motor;
  • A faulty electronic module must be rectified by a qualified technician. If you do not have certain skills in this area, then your attempts to repair the board yourself may cost you in its subsequent complete replacement with a new one. Electronics is an expensive thing and its purchase will not cost you cheap;
  • If the drive belt is stretched, it must be replaced. You can, of course, pull it on, but a small number of washing machine models have this option;
  • The malfunction of the motor windings is corrected by rewinding the stator or rotor. This breakdown can only be repaired with the help of a master. But as practice has shown, this is ineffective due to the high requirements for this procedure. To avoid damage to the windings, do not overload the washing machine. In frequent cases, a malfunction appears due to wear of the current-transmitting brushes. These parts are designed to transmit current to the rotating rotor and are subject to inevitable wear during operation.
  • How to wash a coat in a washing machine
  • How to wash a blanket in a washing machine
TURBION.NET 2021