Samsung Error Code

Air conditioner error codes

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

E464. Overload of the power module by current

E461 Compressor does not start

E473 compressor lock

E466 DC board module voltage error has occurred

E221 An error has occurred with the outdoor temperature sensor

E416 overheating has occurred

E251 An error occurred with the temperature sensor

E468. Electric current sensor error

E465 compressor error

E237. Temperature sensor winding error

E202 connection time (1 minute) expired

E458 Fan error has occurred

E471 OTP error occurred

E467 compressor rotation error

E440. Operation condition secession Low

E441. Operation condition secession High

E469 DC-Link voltage sensor error has occurred

E462. I_trip error / PFC Over current

E554 Refrigerant leakage occurred

E472. Ac voltage zero crossing error has occurred

E556. Capacity Miss-match

E121 indoor air temperature sensor closed / cut

E122 short / cut off temperature sensor of the evaporator

E154 Indoor fan error has occurred

E101 connection time (1 minute) exceeded

Blinking of all indicators. Eeprom (internal non-volatile memory) error

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

01 there was a short circuit of the air temperature sensor or an open circuit;

02 there was a short circuit in the evaporator temperature sensor or an open circuit;

03. Poor connection between the control panel and the wired indoor unit;

04 error of the float sensor of the condensate level or pump (drainage pump);

05. Error in connecting the external to the indoor unit;

06 there is a short circuit of the outdoor temperature sensor or an open circuit;

07 switching on the indoor units of the multisystem to different operating modes;

Hl. Error like 04, float sensor open;

Cl. Child lock is installed, to enable, press Timer Min Buttons for 3 seconds;

Po. Jet cool mode is set, to exit press jet cool button

21 compressors are overloaded by current;

22. The compressor current exceeds 14 A;

23. Dc has voltage below 140V (voltage after conversion module, not power supply);

24. Low / high pressure error, pressure sensors open;

25. Supply voltage is lower / higher than normal;

26. Dc Compressor Position;

27. Psc error has occurred (inductor, reactor);

28 DC Link High Volts;

32 Discharge pipe is hot (INV);

33. Discharge pipe is hot (Cons.);

40 CT short circuit has occurred;

41 temperature sensor D-Pipe closed / interrupted (INV);

44 the outside air temperature sensor is closed / cut;

45 closed / cut off the condenser temperature sensor;

46. ​​the sensor on the suction tube has closed / broken;

47. D-pipe sensor closed / cut off;

48 absence / breakage of D-pipe sensor and air temperature sensor;

51. Combined type power overload;

52 a connection error occurred (main micom-sub micom);

53 a connection error has occurred (outdoor-indoor units);

54 reverse phase, incorrect phase sequence, for three-phase systems;

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

60. Eeprom error (internal non-volatile memory);

61 condenser tubes (condenser) are hot;

62 the heatsink has a high temperature (most likely, this is a heatsink for cooling an inverter power module);

63 the condenser is at a low temperature;

65 there was a short circuit / breakage of the temperature sensor;

67 blocking of external BLDC (brushless DC motor) fan;

105 fan control and main control board do not communicate with each other.

Error codes for LG Art Cool air conditioners and all other wall-mounted LG air conditioners:

Ch1 or C1 there is a short circuit in the internal air temperature sensor or an open circuit;

Ch2 or C2 there is a short circuit in the evaporator temperature sensor or an open circuit;

Ch4 or C4 there is a short circuit of the condenser temperature sensor or an open circuit;

Ch5 or C5 indoor and outdoor units are connected;

Ch6 or C6. The current in the inverter module circuit is exceeded;

Ch7 or C7. Compressor current exceeded;

Ch8 or C8 no rotation of the indoor fan;

Ch9 or C9 no rotation of the outdoor unit fan;

Ch-10 or C10 thermistor for temperature control of the compressor of the Split system is faulty (short circuit or open circuit occurred);

Ca. The discharge temperature exceeds 130 degrees Celsius;

Cc EEPROM (internal non-volatile memory) error has occurred;

Cd an error has occurred in the inverter module;

Po no error, the system is in power saving mode;

Lo no error, finding the system in test mode.

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

Examples of error indications:

E0 trip of a general protective device, where E is a classification code and 0 is a detailed code

Indoor UNIT ERRORS

A0 general protective device tripped

A1 indoor unit PCB defective

A2. Fan motor blocked

A3 invalid level in the drainage system

A4 heat exchanger defective

Samsung Error Code

A5 heat exchanger overheating

A6 fan motor overloaded

A7 louver drive defective

A8 overcurrent (general)

A9 electronic expansion valve defective

Aa heater overheated

Ah the air filter is clogged

Ac started idle

Aj performance is incorrectly set (indoor unit)

Ae insufficient water supply

Af humidifier breakdown

C0 general sensor malfunction

C3 drain level sensor defective

C4 heat exchanger temperature sensor 1 defective

C5 heat exchanger temperature sensor 2 defective

C6 fan motor overloaded, sensor blocked

C7 blind actuator sensor out of order

C8 input current sensor failed

C9 breakdown of inlet air thermistor

Ca breakdown of the output air thermistor

Ch clogging sensor works

Cc humidity sensor failure

Cj temperature sensor on the remote control does not work

Ce radiation sensor breakage

Cf high pressure sensor out of order

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

E0. General safety device tripped

E1 outdoor PCB defective

E3 works HPS (high pressure sensor)

E4. Lps (low pressure sensor) is working

E5 compressor motor overloaded, overheating relay tripped

E6 compressor motor overcurrent blocked

E7 fan motor blocked over current

E8 overcurrent (general)

E9 electronic expansion valve defective

Ah. Pump blocked

Ec. Peak water temperature

Ej. Additional protection device triggered

Ee critical water level in the drainage system

Ef failure of the heat storage unit

H0. General sensor malfunction

H1. Air temperature sensor defective

H2. System power supply is faulty

H3. High pressure sensor defective

H4 low pressure sensor defective

H5. Overload, compressor stop

H6 compressor overload, system locked

H7 fan overload, system locked

H8. Input voltage drop

H9. Abnormal intake air temperature

Ha abnormal outlet air temperature

Hh water pump blocked

Hc. Hot water sensor signal

He signal of the level sensor of the drainage system

Hf heat storage unit above out of order

F0 protective system devices No. 1 and No. 2 are functioning

F1. The protective system device No. 1 is functioning

F2. The protective system device No. 2 is functioning

F3 abnormally high discharge pipe temperature

F6. Inadmissible temperature in the heat exchanger

Fa. Impermissible charge air pressure

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

Fh oil overheating

Fc. Impermissible intake air pressure

Fe impermissible oil pressure

Ff invalid oil level indicator

J0 thermistor defective

J1. General malfunction of the pressure sensor

J2 current sensor defective

J3. Breakdown of the temperature sensor of the discharge pipe

J4. Sensor defective at low pressure saturation point

J5. Thermistor defective on suction pipe

J6. Thermistor defective on heat exchanger (1)

J7 thermistor defective on heat exchanger (2)

J8. Thermistor defective on liquid pipe

J9. Thermistor defective on the gas pipe

Ja discharge sensor defective

Jh temperature sensor ground defective

Jc. Suction pressure sensor defective

Je. Oil pressure sensor defective

Jf. Oil level sensor defective

L0. Inverter system defective

L3. The temperature of the control box is increased

L4. The temperature of the heat sink of the power transistor is increased

L5. Short-term DC overload at the output

L6. Short-term overload of alternating current at the output

L7 total input current high

L8 electronic thermal relay delay

L9 safety stop

La power transistor failure

Lc. Disconnection of communication with the inverter in the outdoor unit

P0. Lack of gas (due to icing of the heat storage system equipment)

P1 no phase, power supply unbalanced

P3 overheating of the control unit

P4 power transistor failed (heatsink temperature sensor)

P5. Dc sensor defective

P6. Dc / AC output sensor defective

P7. Input current (in multisystem) increased

Pj outdoor unit, performance is incorrect

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

U0. Low pressure in the system due to lack of gas

U1. Phases are incorrectly connected (it is necessary to change phases)

U2 low voltage in the power supply

U3. General error in data transmission

U4 communication failure between outdoor and indoor units

U5. Communication failure between the remote controller and the indoor unit

U6 communication failure between master and slave indoor units

U7 communication failure between battery or outdoor units

U8 communication between control panels broken

U9 lost communication with another system

Ua the parameters of the outdoor unit are incorrectly set

Uh. No address entered (outdoor / indoor unit)

Uc. The address on the CPU is set incorrectly

Uj communication with peripheral equipment is broken

Ue. Communication failure between the CPU and the indoor unit

Uf. Incorrect installation: wiring / piping

M1. Defective printed circuit board (central control equipment)

M8 communication failure with control center equipment

Ma. The connection of the central control equipment is broken

Mc. Dual assignment of the CC equipment address

31.The humidity sensor of the circulating air is faulty

32. Outdoor humidity sensor defective

33.Sensor supply air defective

34.The circulating air temperature sensor is faulty

35. Outdoor temperature sensor defective

36.The temperature sensor of the control panel is faulty

3a. Water leakage sensor # 1 is faulty

3h. Water leakage sensor # 2 is faulty

3c. Dew condensation sensor defective

40. Humidifier valve defective

41.The cold water valve is faulty

42 hot water valve defective

43. Cold water heat exchanger defective

44.The hot water heat exchanger is defective

51. Supply air fan motor overloaded

52.The circulated air fan motor is overloaded

53.Inverter air failure

54. Air circulation of the inverter is broken

60.General mistake

61.The PCB is defective

62 unacceptable ozone concentration

63.D pollution sensor defective

64 sensor of the room temperature control system is faulty

65. Sensor of the outdoor temperature control system is faulty

68 failed high voltage system

6a the damper damper of the system is out of order

6h. Open door switch

6c humidifier element needs replacement

6j. High efficiency filter needs replacement

6e. Odor removal catalyst requires replacement

6f. Simplified control panel defective

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

When a system malfunction appears in the Panasonic systems, they are blocked and the chronometer LED on the front dial will begin to pulsate.

If this climatic device is with a multi-split security system, then it is necessary to decrypt the code abbreviations of the faults in a separate order.

(H00) No violations were found

(H11) There is no interaction between the outdoor and plug-in unit, the control boards do not work

(H12) violation of the parameters of the power characteristics between the outdoor and plug-in unit

(H14) air mass supply detector is faulty

(Н15) violation of the compressor unit temperature detector operation mode

(Н16) low current consumption of the outdoor unit. Lack of cooler, open circuit, faulty external module board, faulty power type IPM device

(H17). Violation of the operating mode of the temperature mode detector at the suction pipe of the cooler

(H19). Violation of the operating mode of the fan motor of the built-in unit Possible objects: power plant, board or wiring connector.

(H21). Drainage system or float detector defective

(H23) N1 evaporator temperature detector defective

(H24). N2 evaporator temperature detector defective

(H25). The ionization radiation propagation unit or the built-in unit board must be repaired

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

(H26) device. Ionizer

(H27) outdoor temperature detector defective

(H28). Condenser temperature detector N1 defective

(H30). Discharge temperature detector defective

(H32). The temperature detector at the output stage of the capacitor is faulty

(Н33) block connection error

(H34) the detector of the temperature regime of the cooling system is faulty

(Н35). Drainage system clogged, pump defect (R motor windings. About 0.2 KOhm)

(H36). Outdoor unit gas tube temperature detector defective

(H37). Temperature detector external unit fluid pipe sensor defective

(Н38) violation of compliance of the outdoor and built-in units

(Н39) violation of the mode of connecting wires and circuits of multisplit systems, defect of the solenoid valve of the external unit

(H41). Violation of the mode of connecting wires and pipelines of the cooler

(H50). Malfunction of the fan motor or its board

(H51) clogging of the outlet system

(Н52) defect in the system of shutdown of the restrictive mode

(H58) block system defect “Patrol Sensor”

(H64) high pressure mode detector defect

(H97) defect in the compressor motor, built-in unit board

(Н98) violation of the protective functions of the built-in unit from overheating in the mode of thermal radiation (high pressure), poor return of thermal radiation from the heat exchanger of the built-in unit, detector defect

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

(H99). Device. The evaporator is covered with ice

(F11) the operating parameters of the 4-way valve are violated

(F17) formation of ice on the built-in unit in standby mode, an error appears on the frozen unit

(F90) various compressor winding defects, inverter board defect

(F91) violation of the operating parameters of the refrigeration circuit, the use of protective functions for low pressure

(F93). Various defects in the compressor windings, defective inverter board

(F94) the need to introduce protective functions due to an increase in the discharge

(F95) exceeding the heating temperature of the heat exchanger of the outdoor unit

(F96). Excess heating temperature of the engine compartment, for multisplit systems. Turning on the temperature sensor

(F97). Overtemperature compressor heating

(F98) introduction of protective functions for the total consumed electricity

(F99) DC error of the protective system, possible situations: compressor breakdown, defect in the transistor system, outdoor unit board current detector, low compressor winding resistance.

Ea code. Indoor and / or outdoor unit installed incorrectly. It is necessary to check the interconnection, electrical circuit. Broken chain.

Eb code. Gross violations of installation, activation of protections up to shutdowns.

Eu code. A startup error message appears for 5 minutes. Turning off the power supply, de-energizing the Mitsubishi Electric split system, remove the batteries from the remote control. After 5 minutes, reassemble everything in reverse order.

This will reset all manual settings to zero and return to the factory settings.

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

Error codes for Mitsubishi Electric air conditioners inverter type.

Code E6. Signal of an error in the connections of the outdoor and (or) indoor units, as well as the sensor receiving signals (signals are not received).

No signal with short circuit.

Code E7. Error signal of connections of outdoor and (or) indoor transmission units

No signal with short circuit.

Code E8. Receive sensor error signal. It is necessary to check the power supply to the sensor. Broken chain.

Code E9. A signal about an error in the operation of external and (or) internal connections between units. The chain is broken. No signal.

Code E0. There is no signal from the remote control (no signal received). The batteries on the remote control need to be replaced.

Code E3. False signal. The signal coming from the control panel of the air conditioner is not formed correctly.

For correction see EU Code.

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

E4 code. Checking the interconnection, the integrity of the pressure and temperature sensors.

Code E5. Checking the mains voltage. Equipment may malfunction.

Ef code. M-NET error, no signal.

It is necessary to check the inter-unit connection, bad contacts or broken connections.

Violations in the sequence of signal formation. Stepper finder is malfunctioning.

To fix, see Mitsubishi Electric EU Code, reset the air conditioner settings, set to factory (default).

Mitsubishi Electric Temperature Sensor Malfunction (TH1).

Inspect the sensor for mechanical integrity. The hermetic connection of the sensor is destroyed. Short circuit of the connecting cable and sensor due to dirt and moisture present on them.

Indoor unit freeze sensor triggered.

Dirty indoor unit, insufficient air exchange due to the fact that the indoor unit is frozen.

Frostbite is caused by a lack of gas. Unscheduled maintenance of the air conditioner is required.

Checking drainage, drainage, because a sensor has been triggered, indicating an extremely high level in the bath. The drain is blocked.

No drain. The drain engine is idling.

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application

Toshiba / Toshiba air conditioner error codes
E01 Communication error occurred between the controller and the indoor unit
E02 Control panel connection error occurred
E03. There was a connection error between the indoor unit and the controller
E04 Outdoor / indoor unit connection error occurred
E06. There is no power to the indoor unit, there was a connection error between units, a connection error, or a malfunction of the outdoor or indoor unit board
E07 SW30-2 temperature sensor malfunction, there was a connection error between the units
E08. Indoor unit addresses are duplicated
E09 control panel settings violated, control panel malfunction
E10. Malfunction of the board of the indoor unit
E12 There was a connection error in the outdoor unit or the indoor / outdoor connection
E15 An error occurred in the indoor unit board, power supply, interconnection, power supply interference
E16 An error has occurred in the capacity of the indoor units, the outdoor unit board is defective or setting error
E18. The control panel is not powered, the indoor unit board is faulty or there is an error in the control panel connection
E19 There was a connection error between indoor and outdoor unit, the board is defective
E20.Separate the cable between lines acording to automatic addres setup method in “Address setup”
E23 An error occurred when connecting outdoor units, this model has only one outdoor unit with one refrigerant circuit
E25. Outdoor unit address not assigned
E26 An error occurred connecting the outdoor units
E28 outdoor unit sequence is broken
E31 board malfunction, interference / interference, error in connecting boards in the outdoor unit
F01. Tcj sensor connection is wrong, sensor is faulty, internal board is faulty
F02. Tc2 sensor connection is wrong, sensor malfunction, internal board is defective
F03. Tc1 sensor connection is incorrect, sensor is faulty, internal board is faulty
F04. Td1 sensor connection is wrong, sensor malfunction, internal board is faulty
F05- TD2 sensor error occurred
F06. Te1 sensor connection incorrect, sensor faulty, internal board faulty
F07. Tl sensor connection is incorrect, sensor malfunction, internal board is faulty
F08. To sensor connection is wrong, internal board is faulty, sensor is faulty
F10. Ta sensor connection is wrong, sensor malfunction, internal board is defective
F12- TC1 sensor connection incorrect, internal board malfunction,
sensor defective
F13 IGBT power module sensor error has occurred
F15 there was an error in the installation of sensors TE1 and TL, sensor failure, internal board is faulty
F16- low / high resistance Ps sensors, Pd connection error, board malfunction, malfunction
F23 Ps / Pd sensor error occurred, 4-way valve error, SV4 circuit board, compressor
F24 high pressure board or Pd sensor error has occurred
F29 An EEPROM error (internal non-volatile memory) of the indoor unit board has occurred
F31- power supply error occurred, external unit board error or power supply interference

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application
H01. Compressor error, supply voltage below / above normal, board error, overload
H02. Compressor error, supply voltage below / above normal, phasing error, board error, overload
H03 board error occurred, current sensor
H04 an error occurred on the compressor, circuit SV5, SV4, refrigerant, 4-way valve
H06 fixing by low pressure sensor Ps pressure 0.02 MPa
H07 low oil level protection set
H08 oil level temperature sensor
H14 an error occurred on compressor 2
H16 oil level sensor short circuit, overcurrent relay error, magnetic switch
L03 Outdoor unit address error has occurred
L04 an error occurred on the address line
L05 Indoor unit priority error has occurred
L06 An error occurred in the outdoor unit and indoor unit priority readings
L07 An error occurred in the address of the external unit
L08- an error occurred in the address of the external unit
L09 an error occurred in the capacity settings of the indoor units
L10 An error occurred setting the model of the external unit
L17
L18
L20 Network adapter error occurred
L28 An error has occurred in connecting external units. Maximum four units in one system, error in the connection between external units, the board is faulty
L29 UART error occurred, settings for external unit violated
L30 An external / internal board error has occurred
L31 Internal board error has occurred
P01. The fan motor is blocked, the power supply to the fan motor is interrupted
P03 insufficient refrigerant, 4-way valve error, inverter converter, TD1 sensor, circuit SV4, SV5
P04. Insufficient refrigerant, 4-way valve error, inverter converter, TD1 sensor, circuit SV2, SV4, SV5, fan motor blocked, power cut to fan motor, circuit recharged, external unit board defective
P05.
P07 An external fan error has occurred, the supply voltage is above / below normal, the power module cooling radiator error, the force module temperature sensor error
P10- An error occurred in the drain pump, indoor unit board
float sensor
P12- Indoor unit fan motor error has occurred
P13 A liquid refrigerant return error has occurred
P15 A refrigerant leak has occurred
P17 TD2 Sensor Error Occurred
P19 4-way valve error has occurred
P20 high pressure protection set
P22 fan defective, board defective
P26 compressor short circuit protected
P29 Compressor Jams
P31 An error occurred in the indoor units
C05 an error occurred when sending signals to the controller
C06 Controller signal reception error occurred
C12 an interface error has occurred
P30 addresses are duplicated

Call the master 8 (495) 565-38-25 and 8 (499) 409-84-95, or by online application
Models:
MCY-MAP0501HT MCY-MAP0401HT
MCY-MAP0401HT2D MCY-MAP0601HT
MCY-MAP0601HT2D MCY-MAP0501HT2D
RBM-PMV0901E RBM-PMV0361E
MMD-AP0091SPH (-C.K) MMD-AP0071SPH (-C.K)
MMD-AP0151SPH (-C.K) MMD-AP0121SPH (-C.K)
MMD-AP0071SH-C MMD-AP0181SPH (-C.K)
MMD-AP0121SH-C MMD-AP0091SH-C
MMD-AP0181SH-C MMD-AP0151SH-C
MMU-AP0091MH MMU-AP0071MH
MMU-AP0151MH MMU-AP0121MH
MMU-AP0181MH
00-0C an error occurred in the indoor air temperature sensor or indoor unit board
00-0d an error occurred on the control board or heatsink temperature sensor
00-11. Fan board or motor malfunction
00-12 control board needs replacement
01-04 fuses on the board are blown, the interconnection is incorrect, the board is burnt
01-05 Inverter board error occurred
02-14. Overload by inverter current
02-16. A short circuit has occurred between the compressor windings
02-17 Current sensor error has occurred
02-18 an error occurred in the sensors of the P.C. Board, temperature
02-19 TD temperature sensor error, P.C. Fees
02-1A An external unit fan error has occurred. Overcurrent, blocked, burned out board or motor
02-1b- condenser temperature sensor or the board is faulty
02-1C the compressor did not start within 20 seconds
03-07. An inverter board error has occurred, there is not enough refrigerant
03-1d. Compressor malfunction
03-1E TD suction tube sensor error occurred, lack of refrigerant
03-1F Compressor does not work due to supply voltage, refrigerant circuit overload
03-08. 4-way valve defective
Models:
RAS-10JAVP-E RAS-13S2AH-ES
RAS-10JKVP-E RAS-13JKVP-E
RAS-13JAVP-E RAS-13SKHP-ES

Samsung washing machine error codes

These are the most common trouble codes for Samsung washing machines.

The error code is displayed in the form of a digital code, exactly as they are shown on our website below.

Samsung error codes

If the pressure sensor detects a frequency lower than (25.20khz) 10 minutes after the start of the drain, this error occurs.

This error code is very common, it can also be read as SE or 5E depending on the state of the digital display.

The error is cleared by pressing the button “Start / Pause” after which the washing machine will restart and try to drain the water again.

The washing machine was unable to fill with water on time.

If the water pressure sensor does not register frequencies at 100 Hz for 2 minutes and if the water level does not reach the set level in 10 minutes, then this error occurs.

The error is cleared by pressing the button “Start / Pause”

An error code means that either the door is open, or the door lock or locking mechanism cannot tell the electronics that the door is closed.

The washing machine has detected an unbalanced load

This error code is for informational purposes only. The washing machine tells you that it is unable to rotate correctly without risk of damage due to unbalanced load.

If the tachogenerator signals do not appear within 2 seconds, this is an error.

There may be a short circuit in the motor

If the tachogenerator registers 300 rpm for 1 second at a given 90 rpm, then this error occurs.

If the pressure sensor registers the frequency of abnormal water level more than 21.00khz), the machine stops working and starts draining the water until the frequency reaches 25.00khz.

If during operation more than 4 times the water level is below the safe water level of the heater, this error will occur.

For this error code you need to check the water heater or thermistor. Basically, the washing machine reports a malfunction of the heating circuit with this error code, but it cannot determine exactly where exactly.

Possible options HE1 overheating, HE2 no heating

The error appears if the thermistor circuitry is faulty or if the voltage across the thermistor is lower than 0.2 V or higher than 4.5 V.

If incorrect frequencies are recorded for more than 5 seconds, a pressure sensor error occurs.

If an error occurs, the water is drained for 3 minutes

Water is drained if an abnormal water temperature is detected at the initial time of water filling.

If the pressure sensor frequency is higher than 25.20khz, the water will be drained by the drain pump.

If the pressure sensor detects a frequency lower than (25.20khz) 10 minutes after the start of the drain, this error occurs.

This error code is very common and can also be read as “SE” or “5E” depending on the state of the digital display.

The error is cleared by pressing the button “Start / Pause” after which the washing machine will restart and try to drain the water again.

If the pressure sensor registers the frequency of abnormal water level more than 21.00khz), the machine stops working and starts draining the water until the frequency reaches 25.00khz.

The washing machine has detected an unbalanced load

This error code is for informational purposes only. The washing machine tells you that it is unable to rotate correctly without risk of damage due to unbalanced load.

The error appears if, after turning on the heating element, the water temperature in the tank changes by more than 40 within 5 minutes″C, or it changes within 10 minutes by less than 2C.

In such a case, the heating element is checked and, if necessary, replaced. To reset the error, turn off the CM, and then turn it on again.

The error appears if, after turning on the heating element, the water temperature in the tank changes by more than 40 within 5 minutes″C, or it changes within 10 minutes by less than 2C.

In such a case, the heating element is checked and, if necessary, replaced. To reset the error, turn off the CM, and then turn it on again.

If incorrect frequencies are recorded for more than 5 seconds, a pressure sensor error occurs.

If an error occurs, the water is drained for 3 minutes

An error occurs if the water temperature in the CM in the tank has exceeded the set values ​​in the allotted time. Non-standard values ​​are considered to be 60C (or more) for synthetic fabrics, 45C (or more) for delicate fabrics, 45C (or more) for wool. If this fault occurs, the drain pump is forced on for 3 minutes

If during operation more than 4 times the water level is below the safe water level of the heater, this error will occur.

If the tachogenerator signals do not appear within 2 seconds, this is an error.

There may be a short circuit in the motor

If the tachogenerator registers 300 rpm for 1 second at a given 90 rpm, then this error occurs.

There may be a short circuit in the motor

If the tachogenerator registers 300 rpm for 1 second at a given 90 rpm, then this error occurs.

Attention!

We are not responsible for your safety if you harm yourself or the washing machine using the recommendations on the site. All manipulations you perform solely at your own peril and risk.
The site contains generalized causes of error codes, and we cannot guarantee that the recommendations will solve exactly your problem.
You should also understand that error codes are not “a panacea”, they will not tell you what the problem is, they only offer the right direction to find the problem and they will not replace the diagnostic skills of a professional. In most cases, using error codes, you can find out enough to investigate and diagnose the cause of the breakdown.

Decoding the error

In modern models of Samsung clippers, foam control is provided. If there is too much foam in the drum, the foam suppression mode is activated. 5d / SUD / SD error means that this mode was unable to lower the foam level, and the machine entered standby mode, waiting for the foam to settle by itself.

Samsung washing machine error code 5D, SUD or SD

You habitually stuffed the laundry into the drum, selected a program and turned on the wash, and after a while you found that your Samsung washing machine has stopped, and the SUD, 5D or SD error appears on the display. A large amount of foam in the drum is visible through the glass of the hatch. It is possible that it even leaks out of the detergent drawer. However, there may be no foam, depending on the problem.

Sud / 5D / SD error what to do, how to fix it yourself

This error of Samsung washing machines in most cases is for informational purposes, and you do not need to do anything right now. Just wait 5-10 minutes, as soon as the foam settles, the machine will continue washing, and after it has finished, check:

  • The drain filter may be clogged causing excessive foam formation. Clean the filter. It is located in front of the washing machine in the lower corner behind an opening door. You can find more detailed information in the instructions for your model of the machine.
  • Are you using powder for hand washing that is not intended for automatic washing machines?
  • Are you adding too much laundry detergent. On average, 5-6 kg of dry laundry requires no more than two tablespoons of powder.
  • Have you washed porous or fluffy items that tend to generate foam? When washing such materials in the future, add less powder.
  • Try to change the detergent, it may be of poor quality or not suitable for your machine.

What to do if the wash does not end, there is a lot of foam, and the Samsung machine constantly displays SUD, 5D or SD on the screen

Then interrupt the wash: start the draining program or open the door of the washing machine and remove the laundry. Then clean the drain filter and run the machine without laundry and detergent for a long program of washing at a temperature not lower than 60C. This will help get rid of excess detergent that could clog the drain system of the machine.

The occurrence of this error in the absence of foam, unfortunately, most likely indicates a breakdown. However, try first cleaning the drain filter of the machine and starting the wash without laundry or powder in any program. If the SD / SUD / 5D code reappears on the display, the intervention of a professional technician is required.