On iPhone it shows that the headphones are plugged in

What to do if the iPhone shows that the headphones are connected?

Why do these “glitches” happen? The most common causes are moisture, oxides and dust clogging. A simple example. Wear phone in dust clogged. iPhone thinks that the dirt is the headphones.

It is worth checking the 3.5mm headphone jack. Various contaminants may have affected the operation of the headphone and smartphone contacts. You can use a simple toothpick or absorbent cotton to clean the connector. The problem could be in the “guts” of your smartphone, which is why the iPhone shows that the headphones are on.

Causes

Dust and moisture are the two main causes of failure. Moisture that got into the headphone jack or power connector could have been slow to oxidize the contacts, creating a short circuit effect and activating the headphone connection function.

It’s the same with dust, because when dust accumulates tightly in the connector it short circuits the connector, simulating a connection to the device.

Starting with the iPhone 7, smartphones have got such an indicator as moisture resistance, and gradually this question began to come to naught. But even in this case nothing can be excluded.

Remember how carefully you use your iPhone? Have you ever had a situation where:

  • It got caught in the rain with you.
  • Dropped it in the snow.
  • Has been in a steam room instead of you.
  • It was in your while you drove your buggy over the sand dunes (joke or not)?).

In any case, stock up on a tool and fix the problem at home.

Abnormal headphone disconnection

If you disconnect your iPhone headphones too quickly, your iPhone may not have recognized the disconnection in time or even think that the headphones are plugged in.

Thus, you may plug in your headphones and then disconnect them from the headphone jack several times. As a result, your iPhone may detect the disconnection of the iPhone headphones and automatically exit headphone mode.

Abnormal disconnection of the headphones

If you disconnect your iPhone headphones too quickly, your iPhone may not have detected the disconnection in time or even think that the headphones are connected.

So, you might plug in your headphones and then disconnect them from the headphone jack several times. As a result, your iPhone may detect the disconnection of the iPhone headphones and automatically exit headphone mode.

See also  How to set up USB on your phone

Restarting

There are many ways to deal with the malfunction you’re learning about. How to disable headphone mode on the iPhone? Users give each other a variety of tips and advice.

iphone, shows, headphones, plugged

You can try to connect the iPhone to the charger and then reset the gadget. Before this, the headset must be removed from the smartphone. If this method didn’t help, it is recommended to repeat the operation, but with the charger plugged in. And instead of the usual reset to perform a Hard Reset. To do this, in the off state press the volume control and power button “iPhone”, after the Apple icon appears, let go, and in the menu select Had Reset.

How to disable headphone mode on iPhone: why does iPhone think that they are connected

Both the iPhone and iPad have two different volume modes called “Headphone” and “Ringtone. These modes work separately from each other, allowing the smartphone to automatically change the volume level when the user disconnects or connects the headphones.

Volume level set in Headset mode will be turned on every time the gadget is plugged in, but will not affect the volume in call mode, so you don’t have to change the volume each time. When iPhone is connected to the headphones, the current mode is displayed in the form of a window with a bell or speaker.

In some cases, when you disconnect the headphones, the mode may not change automatically and the smartphone will remain in Headphone mode instead of going to Chime mode. The device stops reproducing sound.

Equalizer: adding bass (low frequency) when listening to music on iPhone and iPad.

Why iPhone thinks headphones are connected?

There are several reasons that can lead to this problem. Among the most common are dirt, dust or water particles getting into the jacks.

In addition, the smartphone may not work properly due to high humidity or mechanical damage.

How to download music to your iPhone or iPad: all the best ways to listen to music on iOS in 2018.

How to turn off the “Headphones” mode on the iPhone?

In this situation, you need to connect your headphones to your iPhone and listen to any sound, such as the lock screen or clicks of the onscreen keyboard. The sound should be output from the headphones only, not from the speaker, otherwise the product is defective. After that, you should disconnect the headphones and check the sound on the speaker of the device using the side buttons. The volume indicator in this case should be in “Chime” mode.

If the “Headphone” mode is still displayed on your iPhone when the headphones are disconnected, do not rush to give the device to specialists from the service center. there are several ways to fix the problem yourself at home. Before trying the recommendations described below, you need to remove the case and analyze the last manipulation with the device.

  • Restarting and charging cable. First try to turn off and turn on the iPhone (with headphones disconnected) with the charging cable connected. If this method does not help, you can do the same but with the power adapter plugged in and a hard reset instead of a normal shutdown.
  • Toothpick. If the headphone jack is rarely used, it may become clogged with dust and dirt from s. You can get it out of there with a toothpick, needle, cotton swab, or corner of paper, first turning on a good light and making sure there are no foreign elements.
  • Vacuum Cleaner. In cases where your device has gotten very wet or has fallen into water, moisture can accumulate in the connectors. You can vacuum it up, but if it’s been a while since you’ve wet the phone, this method may not help due to rust on the pins.
See also  How to record from a microphone on your computer

How to identify a “drowned” iPhone, or where is the moisture (water) sensor on your iPhone X, 8, 7, 6s, etc.д.

  • Reset. Factory reset can help if the problem lies in the software part of the device.
  • Hair Dryer. If the contacts get wet, after vacuuming, you may try drying them with a hair dryer.

Exit iPhone headphone mode with FoneLab

Whatever the cause, here’s the ultimate iPhone headphone mode fix:

FoneLab iOS System Restore can help you get out of headphone mode. Let’s take a look at this tool.

A key feature of FoneLab iOS System Recovery:

  • Fix iPhone, iPad or iPod from DFU mode, recovery mode, iPad gets stuck on Apple logo, headphone mode, can’t slide to unlock, iPhone keeps rebooting and t. д. To a normal state.
  • Support all iOS devices such as iPhone X / 8 / 8 Plus / 7 / 7 Plus, SE, iPhone 6s Plus, iPad Pro, iPad Air, iPad mini, iPod and more.
  • This iOS system recovery is easy to use and safe enough to avoid data loss.
  • Available in both Mac and Windows versions.

If you can’t slide to operate iPhone, please check how to unlock disabled iPhone.

Choose what state your device is in:

How to get out of headphone mode on iPhone

Step 1 Download and install the software on your Windows or Mac computer, respectively.

FoneLab allows you to switch your iPhone / iPad / iPod from DFU mode, recovery mode, Apple logo, headphone mode, etc. Д. To normal state without data loss.

  • Fix disconnected iOS system problems.
  • Extract data from disconnected iOS devices without data loss.
  • It’s safe and easy to use.

Step 2 Connect your iPhone to your computer after completing the installation. Select Restore iOS system on the interface.

Step 3 The software will detect that the connected iPhone is in an abnormal state, such as Stuck in Apple logo, Recovery mode, DFU mode, iPhone black screen t.д., And it will ask you to press Start to start.

Step 4 You will be asked to confirm the information related to your iPhone. Press Fix if it’s correct, but if not, select the exact information manually before repairing. To fix your iOS, the program will download the latest version of your firmware after detecting your current iOS version.

See also  Why iPhone shuts down in the cold

Step 5 It will download a plugin to repair the corrupted system and fix it normally. It may take some time to complete, please do not unplug or operate your device while it is downloading.

This is it! Your iPhone should already be fine and displaying Ringing when without headphones.

Super easy, really? This can also recover iMessages or other data on your iPhone.

How to fix an iPad always stuck in headphone mode safely

Run iOS System Restore

Download and install this program on your Mac or Windows PC. Click ” Tools” and choose “Repair iOS System”. Connect your iPad to your computer using the USB cable.

Free Download Free Download

Put your iPad in Recovery / DFU mode

Tap the Start icon to start fixing your iPad hanging up in headphone mode. Follow the provided instructions to put your iPad into recovery mode or DFU mode.

Confirm iPad information.

Check the detected iPad information below. Fix it manually if something is wrong. To be more specific, you can fix “Device Category”, “Device Type”, “Device Model” and “Update to iOS Version”.

Shut down the iPad from headphone mode

Click the “Repair” button to start downloading the firmware package. After iOS System Recovery completes the plugin download process, it will automatically fix the iPad hanging in headphone mode.

Consequently, you can connect the headphones to the iPad again to see if it’s hung or not in headphone mode. So if you want to disable the headphone control but can’t find it, just ask for help from iOS System Recovery.

Вот и все, как исправить застревание iPad в режиме наушников из-за повреждения водой, сломанного разъема для наушников и большинства возможностей. Contact us if you experience any problems.

Connect a Bluetooth headset/speaker

It is also possible that your iPhone hangs in headset mode due to a software error. This usually happens after installing a new version of iOS. Connecting a wireless headset or speaker and then disconnecting the headphones can help. The principle of the action is as follows:

Connect your Bluetooth headset/speaker to your iPhone to output sound to it.

Disconnect wireless device.

Right after that you can check if the sound is back on the speaker of your iPhone.

iphone, shows, headphones, plugged
Denial of responsibility | Contacts |RSS | SE | EN | BR | DE