iPhone got into zero and does not turn on

Iphone does not turn on

Когда «iPhone» отключается, не заряжается и не включается (например, вибрирует, показывает логотип и сразу гаснет), не спешите ехать в сервис или вызывать мастера. In some cases, problems with Apple technique can be solved without qualified intervention. With the help of our tips, you can diagnose at home and eliminate the cause of the malfunction yourself.

iphone, does, turn

The causes of the iPhone breakdown can be software and hardware. In cases where the phone is hanged or off, t.To. Incorrectly configured and buggy, most likely, you can fix it on your own. At home, you can also disconnect and connect the battery if you have the experience of disassembling the iPhone and you have tools: a paragraph, suction cup, tweezers.

If the iPhone does not turn on due to complex hardware malfunctions, it is better to immediately contact a qualified specialist. Visit Apple’s service center if you suspect a factory marriage. And urgently consult a workshop for help if you spilled on the iphone liquid: tea, coffee, juice or other drink. You can not dry the display with a hairdryer, you need to immediately carry the gadget to the master. It is important to clean the contact sites and boards in time to prevent corrosion inside the iPhone.

  • The battery was completely discharged or was in the cold (in this case you need to wait. The phone does not turn on only temporarily).
  • The smartphone was dropped, incorrectly repaired or flooded with liquid.
  • The factory marriage of parts (for example, power controller, U2 chip or battery. The phone will not turn on).
  • The work of the software (iOS itself or other software itself) is broken).

This is normal if the phone turned off after the battery is completely discharged. In this case, it must be put on charging and turned on after 10-15 minutes. If the smartphone does not give signs of life, it may not have begun charging. Check if there is a current on the network and whether the charger is broken.

Other performers in Yudu

Among the problems that can be fixed with your own hands can be both banal, for example, the use of a cheap Chinese fake instead of the original Apple charger, and quite serious, for example, software failures (software directly affects the chipper controlled).

Pay attention to the charger. Even the original Apple cables are fragile (braids and veins are easily damaged), so what to expect from cheap Chinese products? The phone can show charging, but it will still be zero if the charger is fake or broken. Use only original charging to avoid such problems.

When charging a battery from a computer, also take into account the operability of a USB port. Perhaps there is not enough current strength. Try the usual Apple charger.

Errors during the operation of programs, breakdown of charging devices and iPhone parts (batteries, connectors, loops, etc.) can manifest itself in different ways. A few examples:

Of iPhones, Xiaomi and Toyota in KAZAKHSTAN

  • Iphone does not turn on after discharge (when the battery sat in zero),
  • The application hangs, does not respond to presses or the screen is completely black,
  • The gadget turns on, but hangs after the appearance of the “Apple” logo,
  • The indicator is burning, but the charge level is very low even for a long time,
  • The iPhone is discharged and does not turn on the charge from the cigarette lighter or computer.

How to Fix My iPhone won’t Turn On (iPhone dead)

Having noticed that the “iPhone” does not turn on after discharge, check if the USB port of the tablet or the stationary computer is broken through which the power supply occurs, and whether the Lighting connector is not contaminated, where the villi and other fine garbage are often hit. In both cases, the phone will simply continue to remain discharged, since the current does not arrive. He does not have enough energy to include. Lighting should be cleaned very carefully. A stream of air or a cloth rolled up with a corner.

With problems with inclusion and charging, first of all, make sure there is a current in sockets. Further, if the phone does not turn on at all, connect it to the charger. In normal condition, the gadget immediately writes that it is charged. The indicator is on, then the process is coming. Remember that the battery is not designed to work at low temperatures. Therefore, wait until the smartphone warms up before connecting the charging, if the battery sat in the cold.

Another situation. You are trying to launch the iPhone, which has been discharged for a long time. If the battery sat down at all, you need to wait 15-60 minutes after connecting the external power and only then press the Home or Power button.

  • Click the power buttons and “home” at the same time (at 7 generation devices. “Power” and the volume button).
  • We are waiting for 10-20 seconds before the Apple logo appears on the gadget screen.
  • Let the buttons. The operating system will start after about one minute.

This method helps with other problems. For example, when the program is “hanging” or not the reaction to the buttons.

Когда логотип Apple то горит, то снова исчезает, нужно провести восстановление. Most likely, the battery sat down due to the software failure. The error was caused by an unsuccessful update of iOS or downloading and installing unlicensed software.

  • Run the iTunes program on the computer and insert a USB cable into the connector,
  • Turn off the smartphone using the combination of Home and Power buttons (if you have iPhone 7, use the volume button instead of Power),
  • Press the “Home” button and, holding it, connect to the computer,
  • Keep Home until the phone screen starts showing the ITUNES logo and the plug icon,
  • On a computer display, the message “The problem with the iPhone arose; It must be updated or restored “,
  • Confirm the recovery.

The procedure for downloading and installing a new version of iOS will take about 30-40 minutes. There is another method of recovery. DFU mode. The method is radical, as it erases all the data on the phone, returning it to the factory firmware. Therefore, it is first necessary to make a backup, sending all your data to the cloud. Photos, videos, music, etc.P. You can do this through the smartphone settings by finding the “Reserve Copy in ICLOD” function and by clicking on the “Create backup” button.

  • Connect the charger (the charge level should be more than zero),
  • After five minutes, disconnect the charger, connect the smartphone to the computer (stationary or tablet) and enable iTunes,
  • At the same time press Home and Power, hold them for exactly ten seconds, then release the on and off button,
  • Keep the “Home” button (15-30 seconds) before notification to iTunes (when entering the DFU mode, nothing should be on the phone screen).
See also  Samsung phone does not turn on and does not charge

It remains to confirm the procedure and click on the “Restore” button. If you forgot to rewrite data from the phone, you can cancel the recovery: turn off the USB cable, squeeze Home and Power for 10 seconds. Then the iPhone will simply reboot.

If the above actions were unsuccessful, most likely the discharge of the battery occurred due to natural wear, factory marriage or damage. If you have dropped or poured the phone before this, you can not even look at the indicator. Urgently give the gadget for repairs or call a specialist at home.

Separately, it is worth mentioning the case of the transfer of hours on January 1, 1970. When making such a joke, the smartphone also does not turn on. It is constantly rebooted, charging does not go further than loading the logo. In such a situation, you should wait when the battery sits 100%. Only after complete discharge can it return its performance. If you need a smartphone urgently, you can contact the workshop or independently disassemble the phone, remove the battery, insert it again and assemble a smartphone. Then the date is dumped and it turns on again. Independent actions are possible if you have skills and professional tools (suction cup, tweezers, spatula).

Before carrying a smartphone to the service center, make sure that the cause of the malfunction is a breakdown in the hardware. And in no case do not postpone the trip or call the master if you spilled water on the iPhone, every hour of delay can aggravate the situation.

Other performers in Yudu

Among the problems that can be fixed with your own hands can be both banal, for example, the use of a cheap Chinese fake instead of the original Apple charger, and quite serious, for example, software failures (software directly affects the chipper controlled).

Pay attention to the charger. Even the original Apple cables are fragile (braids and veins are easily damaged), so what to expect from cheap Chinese products? The phone can show charging, but it will still be zero if the charger is fake or broken. Use only original charging to avoid such problems.

When charging a battery from a computer, also take into account the operability of a USB port. Perhaps there is not enough current strength. Try the usual Apple charger.

Errors during the operation of programs, breakdown of charging devices and iPhone parts (batteries, connectors, loops, etc.) can manifest itself in different ways. A few examples:

  • Iphone does not turn on after discharge (when the battery sat in zero),
  • The application hangs, does not respond to presses or the screen is completely black,
  • The gadget turns on, but hangs after the appearance of the “Apple” logo,
  • The indicator is burning, but the charge level is very low even for a long time,
  • The iPhone is discharged and does not turn on the charge from the cigarette lighter or computer.
iphone, does, turn

Having noticed that the “iPhone” does not turn on after discharge, check if the USB port of the tablet or the stationary computer is broken through which the power supply occurs, and whether the Lighting connector is not contaminated, where the villi and other fine garbage are often hit. In both cases, the phone will simply continue to remain discharged, since the current does not arrive. He does not have enough energy to include. Lighting should be cleaned very carefully. A stream of air or a cloth rolled up with a corner.

With problems with inclusion and charging, first of all, make sure there is a current in sockets. Further, if the phone does not turn on at all, connect it to the charger. In normal condition, the gadget immediately writes that it is charged. The indicator is on, then the process is coming. Remember that the battery is not designed to work at low temperatures. Therefore, wait until the smartphone warms up before connecting the charging, if the battery sat in the cold.

Another situation. You are trying to launch the iPhone, which has been discharged for a long time. If the battery sat down at all, you need to wait 15-60 minutes after connecting the external power and only then press the Home or Power button.

  • Click the power buttons and “home” at the same time (at 7 generation devices. “Power” and the volume button).
  • We are waiting for 10-20 seconds before the Apple logo appears on the gadget screen.
  • Let the buttons. The operating system will start after about one minute.

This method helps with other problems. For example, when the program is “hanging” or not the reaction to the buttons.

Когда логотип Apple то горит, то снова исчезает, нужно провести восстановление. Most likely, the battery sat down due to the software failure. The error was caused by an unsuccessful update of iOS or downloading and installing unlicensed software.

  • Run the iTunes program on the computer and insert a USB cable into the connector,
  • Turn off the smartphone using the combination of Home and Power buttons (if you have iPhone 7, use the volume button instead of Power),
  • Press the “Home” button and, holding it, connect to the computer,
  • Keep Home until the phone screen starts showing the ITUNES logo and the plug icon,
  • On a computer display, the message “The problem with the iPhone arose; It must be updated or restored “,
  • Confirm the recovery.

The procedure for downloading and installing a new version of iOS will take about 30-40 minutes. There is another method of recovery. DFU mode. The method is radical, as it erases all the data on the phone, returning it to the factory firmware. Therefore, it is first necessary to make a backup, sending all your data to the cloud. Photos, videos, music, etc.P. You can do this through the smartphone settings by finding the “Reserve Copy in ICLOD” function and by clicking on the “Create backup” button.

  • Connect the charger (the charge level should be more than zero),
  • After five minutes, disconnect the charger, connect the smartphone to the computer (stationary or tablet) and enable iTunes,
  • At the same time press Home and Power, hold them for exactly ten seconds, then release the on and off button,
  • Keep the “Home” button (15-30 seconds) before notification to iTunes (when entering the DFU mode, nothing should be on the phone screen).

It remains to confirm the procedure and click on the “Restore” button. If you forgot to rewrite data from the phone, you can cancel the recovery: turn off the USB cable, squeeze Home and Power for 10 seconds. Then the iPhone will simply reboot.

If the above actions were unsuccessful, most likely the discharge of the battery occurred due to natural wear, factory marriage or damage. If you have dropped or poured the phone before this, you can not even look at the indicator. Urgently give the gadget for repairs or call a specialist at home.

Separately, it is worth mentioning the case of the transfer of hours on January 1, 1970. When making such a joke, the smartphone also does not turn on. It is constantly rebooted, charging does not go further than loading the logo. In such a situation, you should wait when the battery sits 100%. Only after complete discharge can it return its performance. If you need a smartphone urgently, you can contact the workshop or independently disassemble the phone, remove the battery, insert it again and assemble a smartphone. Then the date is dumped and it turns on again. Independent actions are possible if you have skills and professional tools (suction cup, tweezers, spatula).

See also  My iPhone's Wi-Fi keeps crashing

Before carrying a smartphone to the service center, make sure that the cause of the malfunction is a breakdown in the hardware. And in no case do not postpone the trip or call the master if you spilled water on the iPhone, every hour of delay can aggravate the situation.

Solution

If the malfunction did not appear because of the blow or fall of the phone, then it is likely that it will be easy to get rid of it. First, try the easiest solutions to the problem.

The output of the smartphone from the “deep” discharge

If the phone is discharged, and after that I still lie down for a while without recharging, then the smartphone will not have enough energy to turn on the screen. If there are reasons to assume a deep discharge of the battery, then just attach the phone to the charger and wait 15 to 20 minutes. Then, without disconnecting from the network, turn on the smartphone. If a picture of charging appears, then everything is in order, it remains to wait for the moment when the iPhone will gain enough energy to load iOS and continue to work.

Reboot the device

Another standard step in solving problems with computer and mobile equipment. Reloading the device. It will help in two common cases. With freezing and when the smartphone enters the “conservation mode”. The latter case often scares uninterrupted iPhone owners. Когда смартфон заряжен, но продолжительное время не использовался, либо редко перезагружался, то он самостоятельно отключается, не реагируя на кнопку включения.

Iphone reboot with the physical button Home (models from 4 to 6s inclusive) is performed using power buttons and “home”. Press the keys at the same time, holding for 15. 20 seconds. This action will send a smartphone to a forced reboot, restoring the normal operation of the device.

A simple reboot may not help if the phone flash failure. The ITUNES application recovery option will help to fix this problem. To do this, connect the smartphone to the computer with the installed program, and after synchronization, select the load option for the last backup. The application will restore software and restart the iPhone.

iphone, does, turn

Solving the problem with the charger

The last hope to get by with “low blood” is a breakdown of the charger itself. Find one hundred percent work and try to charge the gadget with its help. Keep in mind that the power supply itself and a USB cable can break. With intense (and not neat) use, the conductive cable veins of.

If non.Original Chinese charging or a cheap automobile adapter was used, then the elements of the power controller may become unusable. It happens that the smartphone ceases to identify the original charger, although it continues to charge with the Chinese analogue. This is the first sign that the power controller will soon be out of order and require a replacement.

Change of components and modules

If nothing helped, then the problem is most likely in the failure of the elements inside the iPhone. It is likely that the power controller itself, connectors and train controls responsible for charging, or the battery, suffered. You can replace them yourself. On the Internet dozens of sites with detailed instructions, but still advise you to contact engineers from service centers. It is likely to damage something when disassembling the device or not to find the reason, since it is guaranteed to diagnose the malfunction only in the SC on special equipment.

Charger problems

Often the reason that the iPhone has sat down and does not turn on the charging is a faulty cable. In places of connection of the wire and adapter, users detect creases. The electric current is not supplied to the device, so the discharged phone will not turn on. It is worth carefully inspecting the charging. This will allow you to detect a breakdown in time.

Connect the iPhone to another charging. If the phone is turned on, then the cable will have to be replaced, sometimes the breakdown cannot be found with the naked eye. Also, the reason can lie in a faulty outlet, so you should not panic ahead of time. A banal solution to the problem is often the right way.

Causes

The most common reasons that the iPhone 7 does not turn on after discharge, include a failure in the power circuit, a breakdown of a microcontroller or error in the. Problems associated with internal details and “iron” should be entrusted to specialists. The program in the program can be eliminated independently.

The iPhone 7 ended the charging, and it does not turn on

If, when connecting to charging, the smartphone does not respond to inclusion, there is a deep discharge or problem at the level of the operating system. With deep discharge, the iPhone 7 needs to perform the following actions:

When the Apple logo lights up on the display, you need to release the keys;

Turn on and off the mode without sound if the smartphone does not load;

If the iPhone 7 does not turn on after the frost, what to do to the user:

Go into the warm room and leave the phone there for 30 minutes;

After that, you can connect the iPhone 7 to the network.

Apple electronics work poorly at negative temperatures. A long stay in the cold can cause a complete discharge of the device.

Iphone 7 does not charge and does not turn on

The lack of charging is caused by several factors: a battery breakdown, a broken power controller/charge or an unoriginal wire or a power adapter. First of all, you need to check the cable. It should not have breaks and violation of integrity. You should also make sure that the original wire is used. If there is an additional charger, you need to connect the iPhone 7 to it. If the phone began to charge, the old cable is broken.

If the replacement of the wire did not help, the breakdown is caused by the battery or controller. These details change only in the service.

Battery replacement prices:

Iphone charges and does not turn on

The main reason why the iPhone 7 does not turn on after charging is the battery. The problem can be caused by deep discharge if the iPhone 7 does not turn on after a long non.Use. You can fix the error in several ways:

Raise the charge level to the lower threshold. To do this, you need to connect the iPhone 7 to the network for 6-10 hours to restore the charge. Then you can try to turn on the smartphone.

If the previous method did not help, you need to change the charging and again connect the phone to the mains.

iphone, does, turn

Enter dfu mode. To do this, you need to charge the smartphone for 6-8 hours. On the computer you should install iTunes and open a downloaded program. Iphone 7 remove from charging and connect to PC, holding the Power and Home buttons. Then you need to release the Power button and hold the “home” key for another 15 seconds. The screen should be highlighted on the screen that signals the readiness of the smartphone for restoration. You need to press the “recovery” and wait for the end of the process. After you can turn on the iPhone 7.

When the phone turned on, you need to observe it. If the charging ends quickly, you have to change the battery. You should also check that the original power cable is used. Charging devices are not from Apple can be designed for another current strength, which negatively affects the iPhone 7.

See also  How much to charge your phone for the first time

Program failure

When malfunctioning in the program, only an apple shines, and the device itself does not respond to turning on. Then you need to carry out a compulsory reboot. Home and Power are held for this.

Causes

The most common reasons that the iPhone does not turn on after discharge, include a failure in the power circuit, a breakdown of a microcontroller or error in the. Problems associated with internal details and “iron” should be entrusted to specialists. The program in the program can be eliminated independently.

The iPhone has ended charging, and it does not turn on

If, when connecting to charging, the smartphone does not respond to inclusion, there is a deep discharge or problem at the level of the operating system. With deep discharge, the iPhone needs to perform the following actions:

When Apple’s logo lights up on the display. You need to release the keys;

Turn on and off the mode without sound if the smartphone does not load;

If the iPhone does not turn on after the frost what to do to the user:

Go into the warm room and leave the phone there for 30 minutes;

After that, you can connect the iPhone to the network.

Apple electronics work poorly at negative temperatures. A long stay in the cold can cause a complete discharge of the device.

Iphone does not charge and does not turn on

The lack of charging is caused by several factors: a battery breakdown, a broken power controller/charge or an unoriginal wire or a power adapter. First of all, you need to check the cable. It should not have breaks and violation of integrity. You should also make sure that the original wire is used. If there is an additional charger, you need to connect the iPhone to it. If the phone began to charge, the old cable is broken.

If the replacement of the wire did not help, the breakdown is caused by the battery or controller. These details change only in the service.

Battery replacement prices:

Iphone charges and does not turn on

The main reason why the iPhone does not turn on after charging is the battery. The problem can be caused by deep discharge if the iPhone does not turn on after a long non.Use. You can fix the error in several ways:

Raise the charge level to the lower threshold. To do this, you need to connect the iPhone to the network for 6-10 hours to restore the charge. Then you can try to turn on the smartphone.

If the previous method did not help, you need to change the charging and again connect the phone to the mains.

Enter dfu mode. To do this, you need to charge the smartphone for 6-8 hours. On the computer you should install iTunes and open a downloaded program. Remove the iPhone from charging and connect to PC, holding the Power and Home buttons. Then you need to release the Power button and hold the “home” key for another 15 seconds. The screen should be highlighted on the screen that signals the readiness of the smartphone for restoration. You need to press the “recovery” and wait for the end of the process. After you can turn on the iPhone.

When the phone turned on, you need to observe it. If the charging ends quickly, you have to change the battery. You should also check that the original power cable is used. Charging devices are not from Apple can be designed for other current strength, which negatively affects the iPhone.

Program failure

When malfunctioning in the program, only an apple shines, and the device itself does not respond to turning on. Then you need to carry out a compulsory reboot. Home and Power are held for this.

Sitting battery on the iPhone? No problem!

If your favorite device has a battery, you need:

  • Connect it to the adapter and charge for about 15 minutes (some devices require charging for half an hour);
  • Then you should try to turn on the gadget without getting out of the outlet;
  • If everything is in order, an empty battery icon appears on the display, inside which there is a zipper (this is a signal that charging is going on and the device will turn on).

Sometimes, if the iPhone does not turn on even after charging, you can observe the icon of the discharged battery, sockets, and also arrows that indicates a zipper. This means that the battery is completely discharged, so it takes extra time to recharge (about a few hours).

Ways to solve the problem

What to do if the iPhone 7 does not turn on? There are four solutions to the problem.

Forced reboot

Operational solution to the problem. Restart the smartphone. To do this, pinch the “Home” and “Power” button with your fingers, then wait 10 seconds. When the specified time passes, a smartphone logo will appear on the screen. The gadget will turn on, then connect the charging to the nest and wait for the battery to charge.

Connection to a charger

Some iPhone owners save on the purchase of charging devices. And not surprising. The originals are not so cheap, and a similar model is easily purchased on AliExpress. Problems of this kind with accessories are often. So connect the phone to the original charger and see what will come of it.

Recovery using the DFU mode

DFU-mode-IOS special mode, which is used to update and restore gadgets. If an emergency occurs when the smartphone cannot update, use this way. If the iPhone 7 plus does not turn on, you need to do the following:

  • Launch on the iTunes computer;
  • Connect the smartphone to the PC using a corporate cable;
  • Turn off the gadget by pressing the power button;
  • Holding this key, press the volume button by 10 seconds;
  • Then release the power button, wait 5 seconds.

Itunes will notify a smartphone connecting. Now press the “Restore” button in iTunes, wait until the operating system starts up.

In case of difficulties, try to choose and install a predetermined firmware manually. To do this, go to iTunes according to the above method and select recovery, holding the Shift key. Now select the firmware file and confirm the choice.

Sometimes Apple gadget refuses to move to DFU-mode. You can understand this by a number of signs:

  • The company’s logo burns on the screen;
  • The ITUNES icon was displayed on the display (the phone is in the Recovery Mode mode, there are no desired points).
  • Itunes does not see a connected smartphone.

Observe such symptoms-try to repeat the transition procedure to DFU mode. Upon completion of the recovery, the phone itself will go into a normal state.

What to do if none of the above methods helped

If the above methods do not help, it remains to take the injured gadget to the service center. Professional masters easily eliminate such problems, and the expenses of the owner of the device will not be as high as when buying a new smartphone.

If the problem has a slightly different character: the iPhone does not turn on the black screen, then read the solution in the article.

Denial of responsibility | Contacts |RSS | SE | EN | BR | DE