Installation of Windows from a flash drive on Lenovo laptop

How to load Lenovo laptop from flash drives?

After buying this laptop, I faced such a problem. The operating system is not installed. At the beginning of the installation, the blue screen comes out, whatever the settings in BIOS. I searched for problems on the sites. Some kind of solution was found, but in fact this is not quite correctly the solution. It was proposed to put the Legasy mode and the SATA mode of the Compatible controller. Хотя скажу что режим сата-контроллера менять не нужно и даже лучше вообще не менять. Because compatibal mode is a compatible mode, a more old and slower reading mode from a hard drive. It is better to leave AHCI. Council. The most optimal settings will give preinstalled in BIOS. At the same time and tell you about the subtleties. If you want to install Windows 7, then everything is very simple. We go to BIOS and the first thing to go to the Exit tab. There we choose OS Optimized Defaults. Win7. And now the joke, that is, subtlety. If you now press F10. That is, save and leave the BIOS to start installing. Then most likely you will have the same thing and again the blue screen. Therefore, I show subtlety. After you selected the mode of the desired system, you must select a item just above Load Defaul Settings. After that, on the Boof tab, you need to check the Legasy modes stand. Click F10 persist and observe how Windows 7 is successfully put. Now, if you want to put Windows 8, 10 and later. Then the above method will not work. Again, if you change the OS Optimized Defaults mode. You will preserve and get out of the BIOS without loading Load Defaul Settings. Then freezes and blue screens cannot be avoided. So how to install Windows 8 or Windows 10 on the Lenovo G50-30 laptop. We put OS Optimized Defaults. On Win8, then everything is the same as in the previous version. Be sure to immediately make Load Defaul Settings. Then you just need to select the Legasy mode for loading from external carriers. The rest to leave everything how the default settings set up. We persist and observe the installation of Windows 8 or 10. For Windows 10. You also need to put the optimal settings for Win 8 in the BIOS. And now generalize. For installation you need a version of Windows do the following actions. One. OS Optimized Defaults. And put the Win7 item for the seven, Win8 for 8ki and 10ki, Others. For others, for example, for XP. 2. Load Defaul Settings immediately after you selected Windows mode necessarily. 3. Correct or change the loading mode to Legasy for installation from carriers. Do not touch the rest of the parameters. Next, you can start installing Windows.

Hey! Today I decided to prepare a simple, but at the same time very useful instruction, which should be useful to all owners of Lenovo laptops. We will download the Lenovo laptop from the flash drive. I have such a laptop, so I can show everything on a real example.

Since many models of modern laptops do not have a CD/DVD drive, many have a question, but how to install Windows? How to download a laptop to restore the system, check for viruses, diagnosis, etc. D. All this can be done with a regular flash drive. Over, if your laptop has a drive, then it is better to use a flash drive to install Windows or load a laptop from some other boot disk. Over, everyone has flash drives, and a pure disk still needs to be found.

Loading Lenovo laptop from a USB drive is just as simply as from a disk. There is practically no difference.

First we need to make a bootable flash drive. Simply put, write down.ISO image of Windows, or other system/USB Driver program. You can look at the example of creating a boot drive with Windows 10. For recording.ISO for a flash drive I advise using the following programs: Media Creation Tool (for downloading and writing Windows 10), Winsetupfromusb, Ultraiso, Rufus, Windows USB/DVD Download Tool. Of course, from such a drive you can download any computer. Not only Lenovo.

See also  How to run Windows installation on ASUS laptop

Preparation of BIOS settings

Installation of Windows on Lenovo is not much different from similar processes with other devices. Immediately before the installation start, it is necessary to properly configure the BIOS.

  • Disconnect the laptop.
  • Press the power button.
  • As soon as the screensaver with the name of the brand appears on the screen, you must immediately click on the keyboard button for access to BIOS. On Lenovo laptops, the F2 button is responsible for this. The F12 key allows you to choose a specific boot device.
  • Now you need to go to the “Security” section and open the “Secure Boot” tab by pressing the “Enter” button when choosing the corresponding point.
  • On the contrary, the “Secure Boot” position needs to be set the “Disabled” parameter, indicating the shutdown of the bootloader protection.
  • Go to the Bios Main menu and open the Boot section.
  • Using the arrow keys, you need to transfer the loading carrier of interest to the very top of the list. This will allow you to set the necessary priority for loading.
  • In the main menu of the BIOS, open the section “UEFI/Legacy Boot” and activate the “Legacy only” mode.
  • Press the F10 button to save settings.

Settings

First of all, it is necessary to install, absent in the system, laptop drivers. This can be done in the device manager.

Next, I go to the site Lenovo. After downloading, I install the necessary drivers.

After the charter, I go to the device manager and check.

Further, I will install the programs necessary for the user:

The setting is completed on this. I give the client to check.

T.I brought a laptop to the client.

installation, windows, flash, drive, lenovo, laptop

How to enter the BIOS on Lenovo laptop

First we turn on the laptop and insert the disc with Windows 7 into the discod. Turn off, pull out the battery, pull out from the laptop power from the network. Put in place food and start a laptop from the novo button. This is such a small button that is located next to the power button.

In a few seconds you get to the service menu. Choosing Russian, keyboard layout. Russian. Next, select

Diagnostics. Extra options. Built.In UEFI parameters

Now the laptop will require rebooting. Click the restart button and voila! We entered BIOS.

Now we go to the keyboard with arrows to the Security section, select the Security Boot item with an arrow and click Enter. We transfer securu parameter to the Disabled position. Off.

We return to the main menu of the ESC key and arrows to the right go to the Startup section. Choose a boot item. Click Enter. In this section with arrows, we find your hard drive. ATA HDD and button (plus) located on the right on the digital block of the keyboard, raise it to the very top of the list. If it does not rise to the very top, then select Windows Boot Manager and the key. (minus) lower it down. In the same way we raise in second place CD-ROM-drive-Atapi CD1.

The next in the line can be put a device from which Windows will be installed in case? If this is not a built.In discode.

Again we return the ESC key, click on the UEFI/Legacy Boot parameter UEFI Only, change it to Legacy Only.

We save the configuration of the F10 key and agree to Enter key.

Keep in mind: if you have forgotten something, they have changed or not so set you to enter the BIOS on Lenovo B590 to restore default settings by removing the rear cover of the laptop (nothing terrible. Only 2 screws) and for some time taking out the cmos battery for some time. Then don’t forget to set the right date and time.

Setting BIOS Lenovo G50-30

To get into the BIOS Lenovo G50-30, you need to press FNF2 or on the left next to the power button, there is a button on the side, by clicking it, you will call this window. Choose BIOS Setup.

See also  How to connect a laptop to a TV without a cable

In the point of Windows License, it is clear that there are no built.In keys. You can also see Lenovo G50 30 Technical characteristics.

First of all, it is necessary to reset the default settings, go to the Exit point and select Load Default Settings.

Now at the OS Optimized Default item, select the Win7 OS item.

We go to Boot, where you should be exhibited:

The next step will be the Configuration item where select USB Mode on USB 2.0, this is done so that you can install Windows 7 64 x in Legacy Support mode.

Again, go to Boot and at the Boot Priority point, select Legacy First

We save all the settings at the Exit Saving Changes item or click F10.

Next, call the boot menu Boot Menu and select your boot carrier, whether it be a boot flash drive or Zalman Virtual CD-ROM, from which you can start installing Windows 7 on G50-30.

It is also important to install Windows 7 64 x, it should either be from a DVD disk if there is or from a carrier connected to a USB 2 port, on USB 3.0 I had blue screens

Installation of Windows from a flash drive on Lenovo laptop

Hello everyone, I’ll tell you how to install Windows 8.1 on the Lenovo G50-30 laptop, this article is a continuation of the article how to replace HDD with SSD with a lanovo G50-30 laptop. It seems that the installation of Windows is a simple thing, but there are troubles with laptops, it’s good that they are solved.

Turn on your laptop and insert a loading flash drive if you don’t know how to make it 7 ways to create a boot flash drive. Laptop load will begin, and you will immediately see that it swore that there is nothing to install the system.

Install Windows 8.1 on laptop Lenovo G50-30-02

We see the warning Default Boot Device Missing or Boot Failed

Install Windows 8.1 on laptop Lenovo G50-30-3

We reboot and we need to get into the BIOS, this combination of FNF2 keys is done

Install Windows 8.1 on laptop Lenovo G50-30-01

Install Windows 8.1 on laptop Lenovo G50-30-05

Install Windows 8.1 on laptop Lenovo G50-30-06

We move to the Boot and Boot Mode menu and set the Legacy Support mode, this mode is needed for installation from a flash drive or in my case with Zalman boxes.

Install Windows 8.1 on laptop Lenovo G50-30-07

Everything is saved by the FNF10 buttes and everything will start loading from your device. After installing Windows 8.1 after a day my laptop Lenovo G50-30 did not load and there was a black screen, I advise you to read how to fix it.

Installation of Windows from a flash drive on Lenovo laptop

Let’s configure the priority of BIOS loading. Now I will show you in pictures (more precisely photos) how you can configure UEFI BIOS and possible “pitfalls”, which are rare, but there are found.

Well, let’s start the BIOS setting Lenovo B590 laptop.

First we will have to go to BIOS itself. We click on the laptop button as soon as the laptop display lights up, or rather, the matrix backlight is shut on the F12 key (if I am not mistaken, it is the key to enter the BIOS).

P.S.: In new models (revision)/bios, this key was replaced by F1. For example on Lenovo B590 20206.

How to do everything that is written above, BIOS will appear in front of you.

And so, we go to the Security tab. Ask why? I will explain to the further. Next, go to Secure Boot.

If you have Enabled, then even setting up the loading from a flash drive or drive, then the laptop will not let you load from them, t.To. This is a protection system and therefore it is required to turn it off.

This is the underwater stone in UEFI BIOS, T.To. Having tuned the BIOS laptop will still not boot from the device you have chosen.

We do it, as it is depicted from the bottom, we turn off this function.

Install Windows Lenovo Ideapad 330S dengan USB FlashDisk

Next, click ESC twice, go to the main BIOS menu and go to the Startup tab.

How we moved to Boot, we see the following.

See also  How to return a laptop to Lenovo factory settings

Here we find the priority of loading, whether it is a flash drive or drive.

P.S.: To select the priority, select a flash drive or drive, and keys (increase) or. (lower) device priority.

Click ESC, and rearrange in the UEFI/Legacy Boot line with UEFI ONLY on Legacy First.

P.S.: It may take a restart of the laptop because the BIOS mode (that is, new functions will be added).

installation, windows, flash, drive, lenovo, laptop

How to install Windows 10 | boot usb on Lenovo Ideapad Laptop

The F10 key retain the BIOS settings and the laptop is automatically rebooted.

Congratulations! They set up the Lenovo B590 laptop BIOS and dismantled certain nuances, without which it would not be possible to launch a laptop from a drive or flash drive.

Installation of Windows from a flash drive on Lenovo laptop

Now you will see in the photographs how easily and simply you can configure the BIOS on the Lenovo G505 laptop to download from a flash drive or drive. In this example, I will show how to boot from the drive. Similarly, you can also load from the flash drive.

This laptop model comes with Windows 8, and as we already understand BIOS UEFI. But I liked the BIOS, the fact that it is possible to switch the work of the hard disk from AHCI to IDE, but this is not the point.

Let’s move on to setting the BIOS laptop Lenovo G505. First we need to get into the BIOS itself, for this we turn off the laptop and press the button located next to the laptop button.

If someone does not understand here photo. Small button with arrow.

After pressing the button, the laptop will turn on and the menu will appear.

We will be interested in 2 and 3 points (“BIOS Setup” and “Boot Menu”).

P.S.: 4 point for restoration of Windows from the image of a signed on a hard drive, that is, if the hard drive has been changed or the Windows was already reinstalled by System Recovery, then this item can be deleted =).

Go to “Bios Setup” and see a brief description of the laptop. We are not interested in it.

Then we go to the “Security” tab, we make as in the photo.

installation, windows, flash, drive, lenovo, laptop

Toby you turn off the option, “Secure Boot” on “Disabled”.

Now we move on to an interesting one, this is to the “boot” tab.

And so, according to default settings in the Boot tab, we see that the BIOS works in the UEFI mode, we make below as in photographs

“Boot Mode” transfer to the “Legacy Support” mode and another option appears.

The option “Boot Priority” is transferred to the “Legacy First” mode.

And they almost finished the BIOS setting up for loading from the drive or flash drive on the Lenovo G505 laptop.

We have to save the settings. To do this, go to the “Exit” tab.

Here we select “Save Changes” and turn off the laptop from the button, or “Exit Saving Changes” and turn off the inclusion button on the inclusion. In the future I will explain why you need to do this.

And the same, why it was necessary to turn off the laptop? I showed the “UEFI” shutdown settings and with the possibility of loading from a flash drive or drive, but at the same time I did not give out the initial priority of laptop launch.To. It was again required to restart for the appearance of devices.

Thereby facilitating and simplifying for us loading from a flash drive or drive.

By turning off the laptop, again click on the Recovery button (which with an arrow). Here we will not enter the BIOS Setup, but let’s move on to the Boot Menu tab.

Choose and click “Enter” and voila see all the devices from which we can load.

P.S.: The flash drive will be signed as USB HDD.

installation, windows, flash, drive, lenovo, laptop

That’s the whole setting of the LEBOVO G505 laptop to download from a flash drive or drive.

Denial of responsibility | Contacts |RSS | SE | EN | BR | DE