How to refuel a cartridge for the Canon Pixma printer

Instructions on how to refue the Canon cartridge of the jet printer of the Pixma series and others

Canon’s dressing is quite possible for the user himself, even if he does not have appropriate experience or skills. It is not so difficult to season with a colored or black “consumable” of a jet printer if you know how to do it correctly, how much ink is needed, have a scheme for the location of colors in the cartridge case.

From this instructions you will learn what you need to carry out the procedure, features and nuances of the process itself, what actions should be performed after installing consumables in the printer. Separately, we will consider the ability to change the type of ink used for printing jet devices Canon.

Instructions for refueling cartridges Canon PG-40, CL-41 PG-510, CL-511, PG-512, CL-513 for printers Canon Pixma MP140, MP190, MP210, MP220, MP240, MP250, MP260, MP270, MP280, MP450. MP460, IP1200, IP1300, IP1600, IP1700, IP1800, IP1900, IP2200, IP2500

Attention. An empty cartridge must be re.Referred immediately after it has ended or after a small amount of time (several days, week). A long simple printer with empty cartridges will lead to the drying of the ink on the printing element of the cartridge, which will lead to a noticeable deterioration in the quality of the print. In addition, such cartridges cannot be reused.

How to Start Making Canon Spongeless Refillable Cartridges: PG-240 CL-241 PG-245 CL-246

And of course, the Canon cartridges themselves, which we will refuel.

It is better to start learning to refill cartridges from a black cartridge, t.To. It is easier in design (one color) and you will have more chances to get a positive result.

PG-37, PG-40, PG-50 cartridges: these cartridges are outwardly identical, differ only in capacity, PG-37 of the lowest capacity, PG-40 of the average, PG-50 of a large capacity, refueling process we will analyze the example of the PG-37 cartridge:

Under the label you will see air holes and a special system of air channels.

refuel, cartridge, canon, pixma, printer

To refuel the cartridge, it is necessary to expand the air holes, for example by a drill with a diameter of about 1-1.5 mm, an awl, a screwdriver or any other sharp object or a tool at hand, in the place of the red point, as shown in the figure.

Recommendation: To expand the gas station, do not use the needle that you plan to refuel the cartridge in the future, so as not to break or score it with plastic.

Try that plastic chips do not get into the cartridge when drilling. If all the same chips hit, then this is not very scary, t.To. Inside the cartridge there is a special sponge holding ink, as well as the filter protecting the print head.

About 10-12 ml of ink goes to one refueling of the black cartridge.

We take a syringe with a capacity of 10 ml, pick up about 10 ml into it, carefully insert the syringe needle into the hole until you feel that the needle rested on the sponge that is located inside the cartridge, passes half the sponge and slowly introduce the ink. The needle can be inserted all the way, not afraid to pierce the cartridge, in the figure the red line shows to which the sponge is located, which holds ink.

If you poured too much ink and they began to spill out of the expanded air opening, it’s not scary, just pump them back into the syringe and wipe the cartridge with a napkin.

After we have done this procedure, we take the cartridge for the upper part and easily shake down, if ink appeared on the print head, we repeat the procedure and pull a little more ink, do this until a drop on the print head appears after shaking the print. If the drop is no longer formed, then we check the mark that leaves the cartridge on the napkin. We lean the cartridge by the printing head against the napkin, and look that the fingerprint clearly coincides with the size of the print element in length. The print should be even, without gaps. If the gaps still take place, then I advise you to turn the cartridge with a print head up and drip a green “Mr. Muscle” on them, wait for the moment the “muscle” is absorbed into the print head and try to make an imprint on the napkin again, if there is no result, then repeat the procedure repeatedly.

That’s all, the cartridge is filled, it remains only to glue the label back and install the cartridge in the printer.

Attention! If you use adhesive tape instead of label, you should not seal all the air channels completely, you need to leave at least a small part of the air track open otherwise, there may be problems with printing.

After installing the cartridge in the printer, if necessary, turn off the monitoring control control of the ink levels, print the dozen checking page and clean the print head.

With cartridges 0 and 0, the processing process is exactly the same, the only difference is that they have more sponge, accordingly, they will keep ink more.

CL-38, CL-41, CL-51 cartridge: since we already know how to refuel black cartridges for these printers and All-In-One Printer, it will not be difficult for us to refuel color cartridges CL-38, CL-41, CL- 51.

For cartridges PG-510, PG-512, PG-37, PG-40, PG-50, CL-511, CL-513, CL-38, CL-41 The following color scheme is relevant:

The location of the colors in the cartridges Canon CL-511, CL-513, CL-38, CL-41

Color diagram of cartridges PG-510, PG-512, PG-37, PG-40, PG-50, CL-511, CL-513, CL-38, CL-41

The only difference in the gas station is that you will have to fill in ink not in one camera, but in three different cameras of different colors of ink. Now the most important thing is not to confuse them. The figure shows where and what color to fill in ink. I also ask you to pay attention to the fact that ink would be poured in moderation, and they do not flow from all sides. We do everything exactly as for a black cartridge only for each color separately. Pour 4 into each camera 4. 6 ml. See that after refueling from below, ink does not flow from the print head.

The figure shows in which place to make holes for refueling the photo of the Canon cartridge and what ink to fill in which holes, we will not describe in more detail the refueling process since everything is described above.

Canon pixma mg 2570s/2470 cartridges refill, Inkjet printer cartridge refill 100% working and Reset

PG-510, PG-512 cartridges: For new printer models, Canon came up with a new design, their refinements affected not only the appearance of the printers, but also the cartridges that use these printers. The figure shows cartridge 10 (PG-510), it differs in appearance from the PG-37 cartridge, but the processing process is exactly the same. PG-512 cartridge is equivalent to the PG-40 cartridge, it has a sponge more volume than PG-510.

See also  Installing google services on huawei

Instructions for refueling cartridges Canon PG-40, CL-41 PG-510, CL-511, PG-512, CL-513 for printers Canon Pixma MP140, MP190, MP210, MP220, MP240, MP250, MP260, MP270, MP280, MP450. MP460, IP1200, IP1300, IP1600, IP1700, IP1800, IP1900, IP2200, IP2500

Attention. An empty cartridge must be re.Referred immediately after it has ended or after a small amount of time (several days, week). A long simple printer with empty cartridges will lead to the drying of the ink on the printing element of the cartridge, which will lead to a noticeable deterioration in the quality of the print. In addition, such cartridges cannot be reused.

refuel, cartridge, canon, pixma, printer

And of course, the Canon cartridges themselves, which we will refuel.

It is better to start learning to refill cartridges from a black cartridge, t.To. It is easier in design (one color) and you will have more chances to get a positive result.

PG-37, PG-40, PG-50 cartridges: these cartridges are outwardly identical, differ only in capacity, PG-37 of the lowest capacity, PG-40 of the average, PG-50 of a large capacity, refueling process we will analyze the example of the PG-37 cartridge:

Under the label you will see air holes and a special system of air channels.

To refuel the cartridge, it is necessary to expand the air holes, for example by a drill with a diameter of about 1-1.5 mm, an awl, a screwdriver or any other sharp object or a tool at hand, in the place of the red point, as shown in the figure.

Recommendation: To expand the gas station, do not use the needle that you plan to refuel the cartridge in the future, so as not to break or score it with plastic.

Try that plastic chips do not get into the cartridge when drilling. If all the same chips hit, then this is not very scary, t.To. Inside the cartridge there is a special sponge holding ink, as well as the filter protecting the print head.

About 10-12 ml of ink goes to one refueling of the black cartridge.

We take a syringe with a capacity of 10 ml, pick up about 10 ml into it, carefully insert the syringe needle into the hole until you feel that the needle rested on the sponge that is located inside the cartridge, passes half the sponge and slowly introduce the ink. The needle can be inserted all the way, not afraid to pierce the cartridge, in the figure the red line shows to which the sponge is located, which holds ink.

If you poured too much ink and they began to spill out of the expanded air opening, it’s not scary, just pump them back into the syringe and wipe the cartridge with a napkin.

After we have done this procedure, we take the cartridge for the upper part and easily shake down, if ink appeared on the print head, we repeat the procedure and pull a little more ink, do this until a drop on the print head appears after shaking the print. If the drop is no longer formed, then we check the mark that leaves the cartridge on the napkin. We lean the cartridge by the printing head against the napkin, and look that the fingerprint clearly coincides with the size of the print element in length. The print should be even, without gaps. If the gaps still take place, then I advise you to turn the cartridge with a print head up and drip a green “Mr. Muscle” on them, wait for the moment the “muscle” is absorbed into the print head and try to make an imprint on the napkin again, if there is no result, then repeat the procedure repeatedly.

That’s all, the cartridge is filled, it remains only to glue the label back and install the cartridge in the printer.

Attention! If you use adhesive tape instead of label, you should not seal all the air channels completely, you need to leave at least a small part of the air track open otherwise, there may be problems with printing.

After installing the cartridge in the printer, if necessary, turn off the monitoring control control of the ink levels, print the dozen checking page and clean the print head.

With cartridges 0 and 0, the processing process is exactly the same, the only difference is that they have more sponge, accordingly, they will keep ink more.

CL-38, CL-41, CL-51 cartridge: since we already know how to refuel black cartridges for these printers and All-In-One Printer, it will not be difficult for us to refuel color cartridges CL-38, CL-41, CL- 51.

For cartridges PG-510, PG-512, PG-37, PG-40, PG-50, CL-511, CL-513, CL-38, CL-41 The following color scheme is relevant:

The location of the colors in the cartridges Canon CL-511, CL-513, CL-38, CL-41

Color diagram of cartridges PG-510, PG-512, PG-37, PG-40, PG-50, CL-511, CL-513, CL-38, CL-41

The only difference in the gas station is that you will have to fill in ink not in one camera, but in three different cameras of different colors of ink. Now the most important thing is not to confuse them. The figure shows where and what color to fill in ink. I also ask you to pay attention to the fact that ink would be poured in moderation, and they do not flow from all sides. We do everything exactly as for a black cartridge only for each color separately. Pour 4 into each camera 4. 6 ml. See that after refueling from below, ink does not flow from the print head.

The figure shows in which place to make holes for refueling the photo of the Canon cartridge and what ink to fill in which holes, we will not describe in more detail the refueling process since everything is described above.

PG-510, PG-512 cartridges: For new printer models, Canon came up with a new design, their refinements affected not only the appearance of the printers, but also the cartridges that use these printers. The figure shows cartridge 10 (PG-510), it differs in appearance from the PG-37 cartridge, but the processing process is exactly the same. PG-512 cartridge is equivalent to the PG-40 cartridge, it has a sponge more volume than PG-510.

The desired tool

Black cartridge PG 445 for a Canon printer

  • In syringes with a volume of 10–20 ml, which you need to buy in a pharmacy, type paint from the jar.
  • Remove the sticker from the surface of the cartridge. Now you will see a factory hole.
  • Depending on the size of the needle, you may have to expand the hole so that the needle can go inside.
  • We insert the needle 1-1.5 cm inward. Do not need anymore.
  • Start slowly downloading the paint. About 8-10 ml enters, so it makes no sense to gain more in the syringe.
  • If the paint leaks a little, then pump it back.
  • Wipe the cartridge case with an ordinary dining room with a white cloth.
  • Back back to its place.
  • Press the “consumable” to the sheet of the print head. You must see a clear imprint.
  • Install the cartridge in the printer and make software cleaning through the service service.

Channel Canon Cl 446 printer

  • Spread on the table several old newspapers or paper sheets.
  • Put the cartridge down pg.
  • Gently turn off the label from above.
  • Evaluate the possibility of entering the needle through a hole that already exists. If its diameter does not allow the needle to enter, then expand it with a screwdriver, drill, awl or stationery knife.
  • Dial 3-3.5 ml of each of the colors in syringes. Separately yellow, red and blue.
  • In turn, enter into holes for no more than one and a half centimeters at an angle of 45 degrees.
  • Sour the paint carefully so that it does not go out.
  • Do not mix up the tanks of the corresponding colors. The following shows their location.
  • At the end, wipe all the streams.
  • Check the quality of the gas station by wetting the cartridge on toilet paper or dry napkin.
See also  How to find out how many paint is left in the printer

Preparation for the process

When everything is already ready, you can proceed to filling the consumables with a new portion of liquid. Act according to the following instructions:

  • Gently remove the stickers from the cartridges. Under them you will see small air holes. But we will also use them to fill them. Unfortunately, their diameter will not allow you to stick a needle there, and therefore you need to expand them with an awl. Make them slightly wider than you need to pass the needle, because in the process of filling the air from the inside, it will not be able to go outside.
  • Start the process of downloading from black. With one hand, hold the cartridge with one hand, and take the syringe with the second and enter it a few centimeters through a hole at an angle of 45 degrees. Release the ink slowly inside, and as soon as they begin to go out, stop the process. Excess “take” back into the syringe.
  • Take similar actions for each of the color shades. But take into account the location of the shades in the Canon 511 cartridge. Above is red, below the left is blue, and on the right is yellow. If you confuse and pour the wrong ink, this will lead to a complete failure of the consumable. Replenishment make according to the priority indicated in the figure below. First pour yellow, then blue, and then. Red.
  • Now you can wipe the stumps of paint with napkins. But also pay attention to the cleanliness of the print head. She should be perfect. It is categorically impossible to use a cartridge with wet PG, which can lead to its breakdown.
  • Now we seal up the housings with a label, which was removed at first, but not hermetically so that the air can continue to circulate. And return the cartridges to their place inside the printer.
  • Try to print, and if there are problems or printing does not begin, then perform actions from the next section of the article.

As an example, we take a set of PGI-520BK and CLI-521 re-refereized cartridges used on the Canon Pixma IP 3600, IP 4600, IP 4700, MP 550, MP 550, MP 620, MP 630, MP 980.

  • Learn all the recommendations prescribed in this instruction. Incorrect actions for installing or refueling can withdraw a printer or cartridges from the working condition. Incorrect operation (for example, moisture getting on the contacts of the chip) threatens that the cartridge may burn out the contact of the chip.
  • The instructions are written for re.Refuelled cartridges with already installed chips with auto show. If there are no chips in your set of re.Refuelled cartridges, then they must be purchased separately or rearrange the disposable from the original cartridges.
  • After installing cartridges, the original cartridges of your printer should be saved. You may need for test procedures or in other cases.
  • Before installing cartridges, prepare the workspace, one.Time gloves. Be careful and careful, in order to avoid getting ink on clothes, furniture and interior elements.
  • When the ink gets into the eyes, rinse immediately with water.
  • In order to avoid clogging of the print head, we strongly recommend not using ink that are not designed to refuel this printer model. Do not use ink dubious quality. Buy ink only in proven places. We recommend using Ink-Mate TM brands (South Korea).
  • Keep the ink in an inaccessible place from the children.
  • Keep ink in a dark place at a temperature of 0 to 35 ° C

Equipment and materials used

ATTENTION. Remove the original cartridges from the printer only after refueling refuelled. Do not hold the printing printer head without cartridges for more than one minute, otherwise the ink remaining in it may dry and this can lead the printer to the failure.

Counted cartridges are similar in shape and capacity original and are supplied at gas stations. Cartridges are equipped with two holes (air and refueling), and installed on the gas station. The gas station is closed with silicone traffic (plug). The cartridge is divided by a partition into two compartments, one of which is filled with foam:

Install the cartridge on the gas station for refueling.

Remove the sticker (yellow-black strip with the inscription ‘pull’) from the air opening.

We collect ink in a syringe. To refuel the PGI-520 black pigment cartridge, 18 ml of ink is needed, for refueling the black and colored cartridges CLI-521, 8 ml of ink is required. Insert the syringe into the gas station and season the cartridge with ink slowly pressing on the piston. Refueling the cartridge can be done both using a needle (more convenient) and without it.

If necessary, tilt the cartridge so that ink is evenly absorbed into the sponge.

Fill in the ink compartment of the cartridge by 80-90%, if necessary, tilt the cartridge so that the ink is evenly absorbed into the sponge.

We close the refueling hole, carefully remove the cartridge from the gas station and install it in the printer.

If the re.Refuelled cartridges for Canon printers are equipped with rubber seals, before installing the cartridges, you need to put on these seals on the printing duz of the printer, as shown in the picture below. A larger seal is designed for a black wide (pigment) cartridge, which is also different in size in relation to the rest of the cartridges.

A small amount of ink after refueling and removing the orange site, but before installation in the printer, you can dig up from the cartridge by pressing the foam compartment back on the side walls of the foam compartment in an ink bottle. Finally making sure that the ink is no longer dripping. Install the cartridge in the printer.

The refueling of the remaining cartridges of the kit is made similarly.

After installation, print the sopel check. In the absence of one or more lines on the dough grid, clean the print head using the printer driver.

Fourteen.For the subsequent refueling in ink, repeat points 1.3.4.5.

refuel, cartridge, canon, pixma, printer
  • Regularly control the level of ink in cartridges and refill them with ink in a timely manner. Ink acts the role of coolant for the printing head. If the printer is printed ‘on dry’, then this can lead to the failure of the print head.
  • For reliable operation of the printer, use only high.Quality ink. Do not try to save on them. Such savings can result in not only problems when printing, but also damage to the printer printing head.
  • Do not continue printing with the ‘Polency’, this can lead to the failure of the print head.
  • We strongly recommend that you print at least 1 page every 2-3 days. The printer printing 1 page per day will last much longer than the printer printing 1 page per month.

It is also worth adding that the refueling of the PGI-5BK, CLI-8 and PGI-425BK and CLI-426 is performed similarly.

If you purchased re.Refuelled cartridges without chips, then the chips must be rearranged from the original cartridges.We recommend carrying out this procedure before refueling cartridges.

How to refuel the Canon printer cartridge

It was the cost of the cartridge for a jet printer that led to the need to learn about how to season it yourself. Buying is no more difficult than finding the desired cartridge. That is why you should know all the subtleties of such work so as not to harm the containers or other components of the device.

  • First you need to prepare the working surface and the necessary tools. No special devices are needed. It is enough to find a table, put a newspaper on it in several layers, purchase a syringe with a thin needle, tape or isolet, gloves and a sewing needle. All this set will save several thousand, so do not worry due to the fact that the list is quite large.
  • The next step will be to open the sticker. It is best to do this as neat as possible so that after the procedure it is possible to return it to its place. If it breaks or a layer of glue loses its former properties, then there is nothing to worry about, because there is adhesive tape and island.
See also  Strengthen the Wi-Fi signal using the second router

This is the instructions for refueling the Canon cartridge can be completed. The main thing is to remember that if you are not fully confident in your abilities, then it is best to provide the case to professionals. So it will not work to save maximum costs, but a significant part of the funds will still not leave your home budget.

How to refuel the original Canon PG-445 CL-446 cartridges, Printers of Canon Pixma IP2840, MG2440, MG2540, MG2940, MX494

After the stickers are removed from the cartridges, you can see the system of air channels and air openings through which we will refuel cartridges. Do not try to stick the needle into these holes as it is, if you do it, the needle will enter very tightly and when refueling in the cartridge, pressure will be created, while ink will flow out of the print head. Therefore, before refueling, air openings must be expanded using a drill or awl. The drill is perfect for 1.5-2mm, after you drilled the hole, you can start refueling. On the starting black cartridge that you got with the printer, the air hole is in this place

For drilling, I personally prefer to use an electric screwdriver with a 2mm drill

In the same way, it is necessary to drill 3 holes in the color cartridge, then you can proceed to refueling. The colors in the color cartridge are located as follows

After everything is prepared, we need to dial ink in syringes for refueling. For a colored cartridge, we need only 3 ml of each color for a black cartridge. 8ml. There is a sponge inside the cartridges, so do not be afraid that when drilling into the cartridge, plastic crumbs will get, when refueling, it is necessary to pierce this sponge by about 1 cm, you will immediately feel it when you lower the needle into the cartridge.

After you have tucked cartridges, you can glue the sticker in place

Before installing already refueled cartridges, it is advisable to clean the printing card of the cartridge using the OCP RSL flushing fluid, for this, turn the cartridge with the print head up and pour a slightly flushing fluid onto it

Then attach toilet paper or napkin folded in several rows from above

Wait a little while flushing liquid and ink from the print head are absorbed into it and wipe the print head

Well, in fact, and that’s all that the printing head is cleaned, the cartridge is refunded and ready for further use

Also, after refueling, there are problems of the following nature. It would seem that we tucked a cartridge, and the printer gives a message that the cartridge is over and refuses to print, while not even capturing the paper. No need to be scared, this is a normal phenomenon! Fortunately in Canon printers, tracking the level of ink can be turned off, and quite simply! To do this, hold the Stop button on which the “triangle in the circle” is drawn and hold it for about 30 seconds after that the printer will stop swearing on the ending cartridge and continue to print. On all Canon printers, this button looks something like this

How to refuel the original Canon Pixma IP7240, MG5440, MG5540, MG6440, MX724, MX924, MG6340, MG7140 (PGI-450, CLI-451)

These devices use the following original cartridges:

PGI-450PGBK (black, pigmenting ink)

CLI-451BK (black, water-soluble photo drawing)

CLI-451C (blue)

CLI-451M (purple)

CLI-451Y (yellow)

Cli-451gy (gray)

1) Install the original cartridge for Canon Pixma on a refueling site. It is also an orange plug, which is complete with an original cartridge. It is very important not to throw out this plug, it will be required when refueling the cartridge!

If you threw away these gas stations, you will have to torment a little, in extreme cases you can use a regular eraser, the main thing is that when refueling, the lower hole of the cartridge is tightly closed when refueling

2) Original Canon PGI-450, CLI-451 cartridges are already equipped with a refueling hole. It is located under a sticker with QR code, for refueling it is necessary to cut the sticker just in size QR code.

3) Removing a sticker with a QR code from the cartridge, you will see a dressing hole closed with a plastic ball. To refuel the Chanon Pixma IP7240, MG5440, MG5540, MG6440, MX724, MX924, MG6340, MG7140, it will be necessary to remove this ball. To do this, we will use the self.Tapping screw!

4) gently screw the self.Tapping screw into the ball, while trying not to touch the edges of the gas station, after which it is necessary to extract the self.Tapping screw along with the ball at the end.

5) So we have prepared a hole for refueling, now you can refuel the Canon PGI-450, CLI-451 cartridges with a needle with a syringe with a needle. About 10-12 ml of ink, Canon Cli-451 will require approximately 6-8 ml of ink to refuel the Canon PGI-450 cartridge. Try to fill in ink slowly and carefully. If you see that the cartridge is already complete, and the ink went over the edge, pump out a little ink back into the syringe and thoroughly wipe the edges of the gas station with toilet paper or a napkin.

6) Now that the cartridge is refueled, it is necessary to tightly close the gas station. I will answer immediately to the most common question. “Is it possible to seal the gas station with tape?””. No, For these purposes, in no case should you use adhesive tape. For sealing the gas station, either the silicone plug or thermocles is perfect, but in domestic conditions from the most affordable materials, you can use paraffin or wax from a conventional candle. Put a piece of paraffin on the gas station, heat it with a match so that the gas station is hermetically closed.

7) Well, actually and that’s all, after the paraffin hardens you can remove the cartridge from the gas station. Caution, from the cartridge from the bottom they can slightly leak ink! Therefore, we recommend putting the cartridge on the toilet paper folded in several layers, and hold it for a few minutes to excess glasses of glasses. After that, the cartridge is ready to work, and you can install it in the printer

8) If the printer blocked the seal and issues a message that the cartridge has ended and the replacement is necessary, it is necessary to disconnect the level of blueberry tracking. To do this, click the Stop button (triangle in the circle) and hold it for 30 seconds, this error will leave, and the printer will not block the seal

In this instructions, you learned how to refuel the Canon PGI-450, CLI-451 cartridge

For refueling, you will need ink for Canon, we recommend using only high.Quality OCP ink for these cartridges, and if necessary, you can buy a special liquid from us for washing printing heads and Canon cartridges. OCP RSL

Denial of responsibility | Contacts |RSS | SE | EN | BR | DE