iPad

How to glue glass on iPad

Tools for installing sun protection film on a window

The following set of tools is used to mount the film:

Required for cutting film. It is recommended to use a knife from a Japanese manufacturer: OLFA “A” (SMT-66) or OLFA SILVER (SMT-65). It makes an absolutely even and neat cut, without damage or chipping.

Designed for mechanical glass cleaning. We recommend using scrapers: Triumph SMT-51 (6 “) and SMT-106 (3”). They remove all impurities (dried paint, adhering particles) without leaving scratches on the glass surface.

Scraper holder (SMT-12) with a profile washer (SMT-17 or SMT-15) helps remove setting and cleaning solutions from glass and film surfaces.

VYGONK AND

With their help, the film will “fit” well on the glass.

ADDITIONAL TOOL

To stick a sunscreen film on a window, you will also need a tool such as:

  • ruler (1.5 m);
  • square;
  • marker (SMT-32) or pencil;
  • sprayer (manual or pump);
  • paper napkins (lint-free);
  • neutral shampoo;
  • sponge.

It is advisable to use filtered or distilled water for mounting the film. It should not contain any mechanical impurities (sand, rust).

It is important to use tools from trusted brands to install the sun protection film on the window. Homemade and low-quality fixtures leave scratches, air bubbles and other defects on the glass.

Glass cleaning stage

To clean the glass surface well, you need:

How to Install Tempered Glass/Screen Protector ? | Robustrion iPad 7th Generation Screen Protector

✓ Make a solution: mix 0.5 l of water with 3-4 drops of neutral shampoo. The proportion may vary depending on the hardness of the water.

✓ Pour the solution into the sprayer and spray the liquid onto the glass. Rub the soapy solution over the glass surface with a sponge.

✓ Clean the glass from adhered particles, dried paint and dirt residues. This will require a scraper with a metal blade. Cleaning should be done in 2 directions: vertical and horizontal.

✓ Wipe the edges of the glass with a paper towel to remove dirt and dust.

✓ Spray the previously prepared solution onto the glass. Walk 3-4 times on the glass surface with a rubber wiper in the horizontal and vertical directions. After each pass it is advised to wash the instrument with a clean solution.

✓ Do not use ready-made products containing ammonia for cleaning glass (for example, “Mister Muscle”). Ammonium residues can deactivate the adhesive on the film, and it will not adhere well.

After these procedures are completed, you can begin to glue the sunscreen film on the window.

Stage Installation (rolling) of the film

✓ Spray generously with the solution from a spray bottle to the desired piece of film and the glass surface. When removing the protective layer, this will reduce the ingress of dust on the glue to a minimum.

✓ Peel off the sunscreen foil starting from the corner, i.e. remove part of the protective lavsan. Further, continuing to wet the opening glue base with the solution, slowly and as accurately as possible remove the lavsan from the entire sheet. It is advisable to stratify the material together: one holds the corners of the film from above (be sure to moisten your fingers with soapy water so that no prints remain on the corners of the film!), The other moistens and removes the protective layer. If there is no assistant: spray the glass with a solution, attach a film to it and carefully remove the lavsan, remembering to constantly wet.

✓ Place the adhesive side of the film on the glass and moisten the outside of the material to ensure a good glide of the tool. Next, you need to carefully smooth out the film with a rubber wiper, expelling water from under the sheet.

✓ Remove liquid residues with polyurethane distillation. The tool should be moved from the center to the edges, without missing a single section. The more effort you put in to squeeze out moisture, the faster the film will dry.

✓ Trim the edges of the film at an angle of 15 °.20 ° using a cutting knife. There should be a distance of 3-5 mm from the borders of the glass to the edges of the film. The gap increases with the thickness of the material: the thicker, the more. When tinting glass, which will subsequently be assembled into a double-glazed window, it is necessary to find out in advance the dimensions of the distance of the structure. This will help to make the correct clearance.

✓ Roll up the edges of the sheet by forcing and tighten them using forcing wrapped in several layers of napkins or just napkins.

The final stage is to put the glass to dry, if gluing takes place in the production of windows. It will take several days. About a day after installing the sun-protection film on the window, you should inspect the work and, if necessary, correct the defects.

If you need to dry several glasses with a film, it is recommended to arrange them so that there is a gap for ventilation between them (that is, dry not in a “pack”).

Film Cutting Stage

The film is cut with a ruler, square and a cutting knife on a perfectly level table. The width and length of the sheet must correspond to the dimensions of the glass, 10 mm per cut on each side (or 15 mm when installing the film on a double-glazed window, standing in the window structure).

If you plan to tint several windows at once, number each cut piece with a marker in accordance with the window arrangement scheme. This will help you avoid mistakes and save time.

How to glue a sunscreen film on glass: instructions

This procedure includes a number of sequential activities. First of all, it is necessary to prepare the room in which the film will be installed. It should be: dry, clean and protected from drafts so that small dust particles from the air do not get under the film. The temperature in the room is not higher than 30 ° С and not lower than 10 ° С. Recommended air humidity. from 20 to 80%.

Detailed instructions on how to properly glue the sun-protective film on the windows:

How to glue sunscreen film on a window?

Correct installation of sun protection film on a window is a laborious process that requires special tools, professional skills and experience. It is best to entrust the tinting or installation of the protective film to qualified installers who know all the nuances of this operation and give a guarantee for their work.

But if you decide to stick the sunscreen film on the window yourself, read the instructions on how to do it correctly. Only a correctly installed film will last as long as possible and will look flawless.

How to stick a protective glass on your phone: Instructions and tips

How to stick a protective glass on your phone? This question arises for everyone who knows that the display is the most vulnerable point of modern smartphones. It is best to apply the protection immediately after purchase. Then the smartphone will last a long time, and you will not have to worry about scratches and chips.

Protective glasses are produced for all models and brands of smartphones with a touch screen: from Sony to Samsung. over, manufacturers claim that glass protects the screen much better than film.

It is heavier, it is a little more difficult to glue it, but it provides complete protection from mechanical damage. Glasses differ in price and performance.

To choose the right one, it is enough to pay attention to the coating. glossy or matte. Matte surface does not glare, but also costs more.

See the Samsung Galaxy S6 review. a phone that is not afraid of falls

Safety glass specifications

The thickness of the protective glass can vary from 0.2 to 0.3 mm.

It consists of five main layers:

  • Silicone layer. Thanks to this layer, the glass adheres to the screen.
  • Retaining layer. Required for strong impact. Even if the display is broken, the protective glass will prevent it from shattering.
  • Antiblock layer. It prevents the display from dimming.
  • Protective, hardest layer. It is he who protects against scratches, abrasions and chips.
  • The oleophobic layer is the upper one. It is water resistant. Prints from the top layer can be easily removed with a regular cloth.

Watch the review of the Zony Xperia Z5 smartphone with oleophobic coating

Glass gluing process

The general algorithm of actions is the same for all smartphones. If you follow the instructions, you can quickly and correctly glue the glass on both Samsung and iPhone.

The first step is to look at what is in the glass box. Ideal if there is an alcohol wipe, a microfiber cloth and well-sealed glass. In the event that something is missing, you should first find the necessary tools, and only then start gluing.

  • First step. Wash your hands thoroughly with soap and water. Otherwise, greasy spots will appear on the display. Then we remove the old film or old glass. To quickly remove the film, just pick it up by the corner and pull it easily. To make it easier to work, it is better to remove the case from the phone.

Advice! Prepare your workplace in advance. Free up some space and set up a good light. If the lighting is insufficient, streaks or dust can be missed.

  • Second step. Screen preparation. We throw away the old film or glass. Then you need to degrease the surface. An alcohol wipe is perfect for this (see Fig.). If not, you can moisten a cotton pad with alcohol. If not, regular fabric and perfume or cologne will do. It is important to carefully process the screen without leaving a single greasy mark or divorce. With poor processing, the glass often peels off and you have to reinstall it.

Motorola Moto X. watch smartphone review with Gorning Gorilla Glass 3

  • After all these manipulations, you need to make sure that the display is cleaned thoroughly enough. Turn the screen towards daylight and see that there are no streaks visible. Try not to touch the screen with your hands. If stains or dust remains, remove or wipe them with a dry cloth.

Advice! If dust cannot be removed with a rag, use scotch tape. You do not need to glue it to the display, you just need to attach it to the screen. The scotch tape will collect all the dust particles. Be sure to use clear stationery tape, as duct tape or strong double-sided tape can damage the surface or leave sticky marks.

  • Then he starts working with the protective glass. Take it out of the box and remove the protective film (see Fig.). What if the glass is stained? In this case, you need to clean it in the same way as the display.
  • We apply glass to the screen (see Fig.). You need to hold it by the edges so as not to leave fingerprints. The glass must be held so that it is at a minimum distance from the screen.
  • Aligning the glass to the speaker and the Home key.
  • We release the glass and it fixes itself on the display.

Advice! Many people fail to glue the protective glass the first time. It’s not scary. Dust, streaks, bubbles are all fixable. To get rid of bubbles, just run a tightly pressed cloth across the screen from one edge of the screen to the other. You should not try to crush the air bubble, otherwise it will shift or split in two, and then it will be more difficult to remove it. And if a little dust is clogged under the glass, it is enough to gently bend the edge and wipe it.

What to do if the glass comes off?

If the protection comes off, there are two possible reasons:

  • The glass was poorly cleaned and degreased.
  • It is not suitable for your specific phone model.

It is worth trying to glue it again, carefully following the instructions. If it doesn’t work out, you need to choose a more suitable glass. Often people buy universal glasses or glasses that are not of their own model. But it is worth remembering that the glass can touch the speakers or buttons and come off.

Smart smartphone case. what is he?

To remove and reinstall the glass, you just need to repeat the entire algorithm above. Manufacturers assure that the glass can be removed and installed several times, but it is better to try to stick it correctly the first time.

Tools and materials

In order to glue the protective glass you will need:

  • Two wipes. wet and paper for degreasing and pre-cleaning the display.
  • Soft cloth or cloth.
  • Adhesive strip or regular tape. Essential for removing dust and dirt.
  • A pair of small strips of tape to fit the safety glass. They need to be glued around the edges of the screen. They help to fix the glass correctly. Those who are confident in their abilities do not need to use stripes. If the sticker is performed for the first time, it is better to play it safe.

The installation of the protective glass is carried out according to the instructions. Usually, a napkin and adhesive strips are already attached to the purchased glass. If they are not there, you can search among the materials at hand. It is important to follow the instructions strictly and take your time.

Preparatory work

Before starting work, prepare the work area and tools. Dust getting under the glass is unacceptable, otherwise the whole screen will be in non-aesthetic bubbles. It is advisable to wipe the table with a damp cloth, check the room. And don’t forget to wash your hands. The technicians in the service centers for the repair of electronic gadgets usually wear thin latex gloves.

glue, glass, ipad

In addition to your phone, to get started, you need to prepare: Adhesive tape. Microfiber cloth. Scraper. Anti-static liquid for screen treatment. Alcohol will do as well. It is better to stick the silicone film on the phone in a well-lit place on a horizontal surface. A regular writing desk will do. This will allow you to see the smallest specks of dust, subtle stains on the surface of the device.

How to stick a protective glass on your phone

Preparatory work How to glue glass on a phone at home A modern phone is a complex high-tech device. It has many useful functions, but at the same time the product is not shock-resistant and durable. To protect devices, various kinds of covers, bumpers, protective films and glass are produced. Below we will tell you how to properly glue the glass on a smartphone with your own hands.

How to glue glass to your phone at home

Working instructions for gluing protective glass are as follows: 1. Use a scraper to pry on the old glass (if it is present on the smartphone). When the cover is broken, it is necessary to slowly remove the individual pieces in turn. First, remove the largest area with a whole piece. 2. Then degrease the display using alcohol or a special liquid. The screen should be clean without a single stain. 3. Wipe the phone dry with a cloth. 4. Carefully remove the film from the protective glass, holding onto the edges of the product. Do not leave fingerprints on the adhesive surface. They cannot be removed later. 5. After removing the protective film, place the glass 5-10 mm from the smartphone, without touching the display. 6. Align the glass to match all the holes for the speaker and active buttons of the gadget. 7. You can lower the consumable to the screen. Due to its good adhesion, it will automatically adhere to the glass screen of the device. 8. If there are bubbles, remove them with a cloth. This must be done carefully, moving from the center to expel air from under the glass. 9. If you find a protective glass for the camera in the kit, stick it on the lens.

This completes the process of gluing the protective glass to the screen of the gadget. It should be added that dense glass, unlike standard film, does not form waves and is much easier to install. If you notice dust on the work surface during work, it doesn’t matter. Peel off the glass, remove dirt from the display, and then repeat the sticker again, following our instructions.

How to change glass on iPad: fast and reliable

Broken glass on a tablet screen is a common problem. Many users are interested in how to change the glass on the iPad, and whether it is worth contacting a professional especially for this.

In fact, if you have the appropriate skills and experience, replacing the display glass along with the touchscreen (which are a single structure, since they are connected) will take no more than an hour or two, or even half an hour.

Why glass replacement is needed

Most often, owners of iPad tablets turn to repair shops because they need to replace the touchscreen. In most cases, this happens after falls, mechanical damage, and so on.

Despite the fact that the glass on the “apple” tablet is very durable, it is still not able to protect it 100%. Even if small chips or scratches appear on the surface of the touch screen, it may partially lose sensitivity, and therefore it will be necessary to replace the glass one way or another.

So, if the iPad does not respond to our touches in any way, reacts partially to them, or does not process requests correctly, the glass may be damaged.

Is it worth it to engage in amateur performances, or is it better to consult a specialist??

Glass replacement steps

Let’s start with the fact that not everyone can cope with this procedure. Suffice it to say that even a master is capable of inadvertently damaging any train.

In this regard, it is recommended to contact proven service centers to qualified and experienced specialists.

The fact is that such repair bureaus often provide a guarantee for the work they have done, which means that you don’t have to worry about your iPad.

Their specialists are faced with replacing glass and touchscreens every day, and therefore this is a familiar procedure for them. All elements of the “apple” tablet are so tightly fitted to each other that the master must have a sufficiently high qualification, as well as be extremely attentive.

Self-activity in this matter is unacceptable, since it can lead to extremely unpleasant consequences, and as a result, the owner of the iPad will have to overpay for repairs.

  • During the repair process, the master heats up the glass of the device around the entire perimeter using a soldering hair dryer.
  • After that, he peels it off and gently lifts.
  • Then he unscrews the bolts, carefully removes the cable and removes the screen.
  • The next step is to carefully peel off the touchscreen and remove the glass. Following this, the surface is cleaned from glue residues.
  • The “Home” button is removed and installed on a new touchscreen.
  • It remains to reassemble everything by gluing a new glass, and check the tablet’s performance.

Let’s get started

Cleaning up the iPhone display.

To do this, we use any microfiber cloth so as not to leave anything superfluous on the screen.

You can also use an alcohol wipe and then wipe the display with a microfiber cloth with a soft cloth.

Additionally, we clean the smartphone screen using the bundled tape or any other sticker.

Just touch the display with the tape and lift it back up. The adhesive surface will collect dust residues.

Now you need to remove the protective film from the adhesive side of the glass and attach it to the screen.

Important: hold the glass by the edges so as not to leave unnecessary marks on it.

Place the glass gently on the iPhone screen.

If the glass is good, it will fit on the smartphone screen by itself. But for greater confidence, you can smooth it yourself.

We run our finger through the center of the smartphone and start smoothing until all bubbles are removed. If there are any small bubbles left, take a plastic card and, using light pressure, slide it over the areas where the bubbles are formed.

For every taste, color and wallet

Mocoll literally has glasses of all shapes and sizes. The assortment includes glasses for tablets and smartphones (and not only for Apple), there is also protection for MacBook.

Among the most interesting options is special glass with anti-glazing protection.

It works in such a way that after gluing you can see what is happening on the iPhone display only strictly at a certain angle. That is, you, as the owner, can easily correspond or watch a movie, and the passenger sitting next to the bus, with all the best will not see anything.

The glasses are designed in such a way that they refract the light coming from the screen, making the picture inaccessible to others.

Mocoll glasses are very popular. Many service centers and workshops use accessories from this manufacturer. They are really very durable.

LLC “DVSOTA” Location 690 018, Vladivostok, Volkhovskaya str. 26a, office9.

How to stick the protective glass on your iPhone yourself

Many iPhone owners try to treat the device as carefully as possible. For this, various covers, bumpers and protective glasses are bought.

Here we will tell you how to simply and quickly glue the protective glass without “defects” in the process.

In this tutorial, we have used Mocoll glass. And it’s not just that

When you look sadly at an iPhone whose display is covered with a pitiless mesh, it’s too late to think about protection. The manufacturer of protective accessories Mocoll took care of the consumer in advance.

All brand products are built in such a way that the buyer spends a minimum of time gluing the protective glass.

Considering that the Chinese brand Mocoll (our review) has been producing protective glasses for several years, the company’s engineers have thousands of hours spent in research laboratories.

Glasses are produced using high-tech equipment and in the process of processing they obtain a number of important properties. Mocoll glasses:

  • They are only 0.33 millimeters thick. The glass is uniform and of equal thickness at any point. Mocoll has one of the lowest manufacturing tolerances among glass manufacturers.
  • Mocoll glasses easily withstand the impact of sharp objects and do not shatter into fragments on impact.
  • Hardness at 9H on the Mohs scale. Higher only in diamond.
  • The glasses have an oleophobic coating, so after gluing you will not feel any tactile changes from interacting with the iPhone screen.
  • Mocoll supplies its products with a rich package. The set has everything you need to glue the glass without additional purchases and the search for a piece of cloth or a plastic card to eliminate bubbles.

Mocoll has several options for safety glasses at once. 2.5D, 3D and advanced design. 3D glasses with elastic edges to match the color of the device case.

As you can see above, it is very easy to install Mocoll safety glasses. Due to the presence of a special silicone layer, you can not worry about the appearance of hated bubbles during gluing.

How to do it

Remove the iPhone case before gluing the screen protector. If the iPhone display is already covered with old film or glass. feel free to remove it. Wash your hands thoroughly to avoid getting dirt on the screen.

It is best to glue in a well-lit place so that you can see every speck that hits the screen of the device. Well, choose the cleanest surface for the glass sticker.

Artyom Bausov

Main on news, clickbait and typos. I love electrical engineering and do fire magic. Telegram: @TemaBausov

How to properly glue the protective glass on your phone yourself

The freshly bought device pleases with perfection, but not for long. even on displays protected by Gorilla Glass, scratches appear quickly. The best way to properly secure the screen today is to glue the protective glass. Even at home, this is easy to do, but there are a number of typical beginner mistakes, due to which ugly stains or air bubbles form under the coating. Strict adherence to the instructions will help to avoid incorrect installation of the glass.

How to install a protective glass on a smartphone. step by step instructions

Instructions for applying a protective glass to your phone:

It is recommended to carry out the procedure in the bathroom or do a wet cleaning first so that all the dust settles. Then wash your hands thoroughly and wipe the table on which everything will take place.

You can pick up the old glass with a bank card, a plastic knife, or a similar tool. It is not recommended to use metal products in order not to damage the original phone screen.

Here is a list of the tools you will need to successfully apply the hardened protection:

You can degrease the display surface with an antistatic agent. a special screen cleaner. or regular alcohol. Some manufacturers produce kits that include a wet and dry wipe in addition to the coating. The first one is impregnated with an antistatic agent, so you do not need to use additional alcohol. After wet processing, wipe the screen dry. Just in case, repeat the procedure for hardened protection.

It is impossible to align the already glued product, so you need to install it as evenly and correctly as possible the first time. To do this, use small pieces of tape:

Put the glass, without tearing off the protective film, with the adhesive side down, connecting all the holes to the desired places on the gadget.

Fix the cover with tape on one side to make a “little book”.

How to Install Tempered Glass Screen Scratch Guard Protector For Apple iPad

Open the “booklet”, remove the protective film from the glass and put it back in the same place. Wait for the product to attach itself to the device.

Removal of missed dust and air

If a bubble appears after sticking, wipe the surface with a dry cloth, blowing air to the edge of the device. It will not work to remove missed dust particles in this way: for this you need to try to lift the glass with a plastic card, quickly glue the adhesive tape in place, tear it off and attach the cover back.

Safety glass functions

High-quality safety glasses are always composed of several layers, each of which performs its own function:

  • silicone provides fixation of the product on the phone screen;
  • anti-reflective coating makes the product matte, it is also responsible for the clarity of the image on the display;
  • the containment layer has anti-shock properties, protecting the gadget in case of falls, reducing the sensitivity to impacts and increasing the strength of the glass;
  • oleophobic coating keeps the screen clean, preventing fingerprints, smudges, grease stains from remaining on it;
  • the protective layer will help against minor damages, scratches.

On iPhone

How to glue glass on your phone without bubbles

Glass is much easier to glue than a protective film. Due to its rigidity, it is less prone to bubbles, and it is easier to position it correctly, relative to all buttons, frames and holes. However, before sticking a protective glass on your phone, you need to remember: it does not like to forgive mistakes.

If a speck of dust gets in and a bubble appears under the film, just peel off its edge and blow out foreign particles or remove it with tweezers. This can be done several times in a row, until the bubbles are completely eliminated. With glass, this option is not always feasible, since it is difficult to peel it off, sometimes it may not work to lift one edge, and if you peel it off and stick it several times, the sticky layer may become unusable, and the glass itself may burst.

The film gluing procedure consists of 6 stages:

  • Before sticking the protective glass on the phone, the screen must be degreased. For this, an alcohol-containing liquid is used. Before work, you should wear medical gloves so as not to accidentally contaminate the screen and glass. Using a napkin moistened with alcohol, you need to carefully wipe the screen, leaving no streaks or stains.
  • Use two fingers to grip the new glass by the edges. Do not touch the sticky layer with your fingers (even with gloves), as this can affect its adhesive properties, impairing the reliability of adhesion. If there is a suction cup, you can grab the glass with it, then the risk of getting prints is reduced to zero.
  • From the bottom side, you need to remove the protective film, keeping the glass at a distance of 5-10 cm from the screen. If you take a greater distance, dust particles can stick to the glass during the movement.
  • After aiming, you should slowly bring the glass to the screen. After it starts to seize, you need to swipe it with a napkin in the middle of the screen (from the earpiece to the buttons.
  • When the center of the protective glass is stuck to the display, it is necessary to squeeze the air out from under it, running a napkin from the middle mowing line to the edges.
  • When the glass is completely stuck, you can remove the shipping film covering the upper part of the glass and feel free to use your smartphone.

Not everyone succeeds in doing everything “without a hitch, without a hitch” the first time. Sometimes it is not possible to remove all the dust, or a small speck has got in already during the gluing process. You can remove it, but this should be done very carefully. Indeed, with a large bend, the glass will burst. And prying off the edge of the glass is more difficult than when gluing a film.

If the trouble does happen, and the dust under the glass prevents it from adhering normally, you need to peel off the edge from the corner closest to the bubble. This can be done with a thin strip of plastic, for example, a bank or discount card. After prying the edge, you do not need to lift it too much. It is enough to leave a gap of a couple of millimeters. You can remove the speck of dust with clean tweezers or blow it out. For this, a can of compressed air, a regular vacuum cleaner or a low-power compressor will do.

After the obstruction has been removed, you can put the edge of the glass back in place. It should be smoothed with the same movements: from the center to the edges.

On Lenovo

Advantages and disadvantages

Previously, the only way to protect the display of a smartphone was with films, but for several years, tempered glass has practically ousted these products from the market. However, there are opponents of both the first and second methods, for whom the disadvantages of additional coverage outweigh the advantages. Which side to be on is up to everyone to decide. List of pros and cons for gluing tempered glass:

TURBION.NET 2021