How to Disassemble a Samsung TV Remote

How to properly disassemble Samsung TV remote

It often happens that the remote control stops working, sometimes insignificant reasons lead to this, for example, the buttons get stuck, in this case it is enough to disassemble the device and fix the problem.

Therefore, for every TV owner, it is important to know how to disassemble the Samsung TV remote control.

  • Features of disassembling the remote control from the TV
  • Dismantling the Samsung TV remote
  • Possible malfunctions and their elimination
  • Connecting and configuring the remote control

Dismantling the Samsung TV remote

To open the Samsung Smart TV Remote, turn it over and slide the back cover down towards the indicators.

If you slide the back of the puller towards the indicators, a small gap appears on the front of the remote control.

Open gap makes it easy to grip the back cover so you can remove it.

Removing the back cover reveals the battery compartment, which usually contains the necessary fasteners. A Phillips screwdriver will help you remove all the screws and unscrew the case. It is advisable to take a special jar or a small container for the screws, so as not to lose them.

How to Disassemble a Samsung TV Remote

The rest of the remote is held on plastic clips, but it can be glued, pay attention to this point.

On the right side of the console, when facing up, there are two large areas for opening from the outside. These large clip opening areas are located on the right side of the console only. If the manufacturer did not use special glue, then you can carefully slide a plastic card around the device and pry off the case to start separating the case seam through the large clamping areas.

Once the case is open, you can see the top and the keyboard with a rubber membrane. Then disconnect the microcircuit, but it is not recommended to unscrew the sensor from it.

It is advisable to wipe the area from the remote keyboard with alcohol, like the keyboard, which will get rid of sticking buttons and pressing will become smoother.

To remove the PCB from the case, use a flat head screwdriver or knife to gently pry the bottom of the PCB on both sides near the battery compartment area.

Close inspection reveals two small holes on the board. These holes are for the two MEMS microphones located in the remote control.

The LED is also located next to one of the microphone holes.

The top of the remote housing has an acoustic spacer for the top microphone. The rubber membrane keypad is used as an acoustic pad for the bottom microphone.

Turning our attention to the reverse side of the PCB, we can look at the components that make the console work. There are a number of discrete parts, transistors, and power supply integrated circuits. For example, a universal electronic remote control with voice control and Wi-Fi Direct UE878NMEG, consists of:

  • Wi-Fi chip, Knowles SiSonic microphone and infrared LED.
  • After cleaning and repair work, you can assemble the remote control, observing the reverse order.

Features of disassembling the remote control from the TV

It should be noted right away that there are no significant differences when disassembling remotes from different brands, since they have a similar design. Often, remote control devices differ only in the size and location of the buttons.

Therefore, further we will consider the general principle of disassembling the remote control, which will suit most models. However, it is recommended to carry out only cleaning on your own, since repair requires certain knowledge regarding the functioning of microcircuits, which may differ in different devices.

When disassembling the remote control you will need:

  • small Phillips screwdriver;
  • knife or flat screwdriver;
  • a plastic card.

Possible malfunctions and their elimination

If the TV stops responding to the remote control, the first step is to check the connection to make sure which of the two devices is causing the problem.

This will require:

  • The first step is to check the connection of the equipment to the power source. If the TV plug is connected and the current is supplied to the outlet, but the TV does not turn on, check the wire itself, it so happens that the cable from the TV to the plug is frayed, bent, etc.
  • If both the plug and the cable are in order, and there is current in the outlet, and the TV does not want to turn on, then try to start it using the button, which is located on the body of the equipment itself. If the equipment does not respond, then it is worth sounding the alarm and checking the performance of the TV itself.
  • In the case when, when turned on with the button on the panel, the TV works as if nothing had happened, and does not want to respond to the remote control, then the question arises of why this happened. Most likely, in this case, the problem is specifically in the remote control.

The most common reasons for a remote control breakdown are

  • Mechanical damage Most often, it is found in families where there are small children who can drown the remote control in the bathroom, bucket. Or throw the remote control at the wall. In such a situation, only a complete replacement of the remote control can help, and it is recommended to remove the new one away from children.
  • Batteries. Typically, TV remote controls are powered by batteries that go into a separate compartment. And to restore the device’s performance, it will be enough to replace the batteries with new ones.
  • Scheme. The circuit can hide in itself various breakdowns, including loose contacts and ending with more serious malfunctions. The most popular chip in use today is Adam24P20G.
  • Quartz remote control device.
  • Buttons. Sometimes there is a thinning of the special gasket between the buttons and the circuit.

Most of the problems can be noticed in the early stages, paying attention to the appearance of the device. For example, the body of the remote control may be melted or cracked, which already indicates possible problems that in the future can lead to a complete failure of the device. However, some breakdowns can still be eliminated if they are detected in time.

If you know the cause of the breakdown, the device can be reanimated if done on time.

You can deal with some faults yourself. For example, if the power supply is insufficient, the batteries must be replaced. No soldering or disassembly required.

  • Remove the panel cover;
  • Remove the batteries;
  • Insert new.

If there is a bad reaction of the buttons to pressing, you will have to check the integrity of the gasket located between the buttons and the microcircuit.

If there are any cracks on the case, it is recommended to replace the remote control with a new one, or use materials at hand to fix the case and prevent further cracking.

But not in all situations you can cope on your own and then you need the help of a specialist.

Connecting and configuring the remote control

After you have disassembled and reassembled the remote control, you will need to reconnect it to the TV.

After inserting the batteries, observing the polarity and closing the cover. Then find in the instructions how the first connection is made. Different models are activated by different keyboard shortcuts. But usually you need to set the play and return keys, holding until the corresponding icon appears on the screen.

This will mean that the devices have successfully connected with each other. For modern universal remotes, no special setting is required, it is important to know only the purpose of each button.

Owners of modern Samsung TVs with Smart Touch Control may find it difficult to get used to using the new system.

The remote control is equipped with a hydrosensor, and Smart TV control is obtained when it moves in space.

The body of such a device has few buttons, since its entire functional part is concentrated on the touchpad, which is located in the center.

So, for example, when you move your fingers, you navigate through the menu, and the touchpad on the panel can call the cursor.

You can select an item from the list by touching the touchpad. Some models provide keyboard mapping to help speed up searches.

But even taking into account all the functionality of touch-sensitive remote controls, users prefer to use universal push-button analogs, because they are cheaper and more familiar to operate at a price.

TV remote control functionality

Before you open the Samsung TV remote control, you need to understand what functionality it performs. This is no longer a simple device with an infrared port and buttons, but a device with a complex design that can:

  • surf the Internet and start playing various videos in its vastness;
  • record video to a media connected to Smart TV;
  • run games;
  • work with USB devices, including. create folders, edit and delete files.

The modern remote control allows you, without getting up from your seat, to use the wide functionality provided by Smart-TV.

How to connect the remote to the TV

After disassembling, as with the first use of the remote control, you will need to connect it to a Samsung TV. We insert the batteries into the corresponding compartment, observing the polarity and close the lid. Next, we turn to the instructions for the device and look for instructions on what to do when connecting for the first time. Different models require different keyboard shortcuts. As a rule, these are return and play, which must be simultaneously pressed and held until the Bluetooth icon appears on the TV.

As soon as you see this icon on the screen, it means that the TV and the remote have “found” each other and have successfully connected. Now you can explore the wide functionality of Smart TV without leaving your seat.

How to disassemble and set up your Samsung TV remote

How to disassemble a Samsung TV remote to change batteries or clean it from dirt that got inside. Regardless of the Smart-TV model for which this device was created, the algorithm will be approximately the same.

Dismantling the Samsung TV remote

To disassemble the remote for Samsung, prepare handy tools that will be useful to you in your work:

  • A small Phillips screwdriver or curved-blade knife
  • unnecessary plastic card.

After preparing the tools, we release the table and put a convenient container to collect the screws, and then we get to work:

  • We examine the remote control and open the battery compartment. Be careful. on some models, the cover is screwed on with screws, so if you see characteristic grooves, do not apply force, but unscrew the screws.
  • Under the place for installing the batteries, unscrew the fasteners with a Phillips screwdriver, and carefully fold the screws into the prepared container so that they do not roll away and are not lost.
  • Using the card, we go through the joints of the parts of the case in order to unclench the joints of the parts and completely open the disassembled console.
  • Carefully remove the rubber keyboard from the remote control.
  • Use a Phillips screwdriver to unscrew the microcircuit at the attachment points. It is not necessary to remove the sensor from it.

Everything is ready, the disassembled remote control can be carefully cleaned or repaired by replacing the failed parts.

Setting up the TV remote

There is no need to configure universal remotes, you just have to study the purpose of the buttons. Owners of TVs with modern Smart Touch Control will require significant work, since it takes getting used to and learning how to use it. The device has a hydrosensor, so Smart TV can be controlled by simply moving the remote control in space.

There are few buttons on the Smart Touch Control body, all the functionality is collected on the touchpad located in the center of the remote control. To make the cursor appear on the screen, just tap on the touch panel, and navigation through the menu sections will be carried out with the movement of your fingers. The selection of an item from the list is confirmed by operating the joystick or by touching the touchpad. Some models are able to display the keyboard on the screen, which allows you to speed up the work and search for parameters.

Despite the wide functionality of touchscreen remote controls, most users prefer to replace them with universal push-button ones, since they are cheaper and more familiar to use.

DIY TV remote control repair steps

Knowing the reason why the remote control broke down, you can decide what should be done to reanimate the remote control. Most often, the remote control has malfunctions, some of which can be eliminated on their own. Let’s consider a few examples of how to restore the operation of the remote control. Insufficient power supply to operate the console circuits. In this case, you will most likely need a simple battery change.

There is no need to disassemble or solder anything. it is just necessary:

  • Open the console compartment;
  • Remove old batteries;
  • Replace them with new ones.

If the buttons react poorly to pressing, you will have to disassemble the device in order to check the integrity of the gasket between the buttons and the remote control circuit. Disassembling the console is a matter that requires appropriate preparations. First of all, there should be a set with small cross-section screwdrivers, both flat and Phillips, at hand. In addition, parsing the remote control will come in handy when you need to lubricate certain parts of the device.

When you know what to do, you can do it on your own. In addition, all these examples will be useful when deciding to repair the remote control yourself. But nevertheless, sometimes you should entrust this work to masters who have been repairing such equipment for several years.

Reasons: why the TV does not respond to the remote control

It does not matter which company is the leader in the production of TVs, Samsung, Philips, Sony, PanaSonyk, LJI or some other company, all equipment may sooner or later fail in its work. And these failures are not only very unexpected, but also quite serious. Before you panic when the TV cannot be turned on from the remote control, you should check if the TV itself works at all?

This requires:

  • First, check if the technician is connected to a power source. Even a small child can handle this. If the TV plug is connected and the current is supplied to the outlet, but the TV does not turn on, check the wire itself, it so happens that the cable from the TV to the plug is frayed, bent, etc.
  • If both the plug and the cable are in order, and there is current in the outlet, and the TV does not want to turn on, then try to start it using the button, which is located on the body of the equipment itself. If the equipment does not respond, then it is worth sounding the alarm and checking the performance of the TV itself.
  • In the case when, when turned on with the button on the panel, the TV works as if nothing had happened, and does not want to respond to the remote control, then the question arises of why this happened. Most likely, in this case, the problem is specifically in the remote control.

If repairing a TV at home is almost impossible, and experts advise contacting the masters in case of such breakdowns, then the remote control can be repaired yourself. But first of all, they must determine why the TV stopped responding to the native remote control.

TV Remote Control Manufacturers

As already noted, a house with a TV has a remote control. Each company itself develops remote controls for its equipment, which guarantees not only the appropriate quality, but also the fact that the remote control will always fit the TV that you bought. It also allows you to quickly pick up a new remote control if the old one is broken. You can pick up the necessary parts much faster if it was decided to repair the remote control yourself.

Among the main brands of TVs and remote controls, the following are the most popular manufacturers:

  • Samsung;
  • Philips;
  • Panasonic;
  • Sony;
  • Lg.

Samsung technology works best with Samsung accessories. In addition, there are options for the remote control for each specific model of TVs, players and set-top boxes, including those related to the Smart system. PanaSonyk, just like Samsung, develops remote control models for each new TV model created, but recently the manufacturer has been trying to create an option that will fit not only a particular type, and freely manage all new models from the company. Which, of course, will help to save money both in material terms and in the promptness of replacement.

At the very beginning of work, both the TV and the remote control usually show themselves from their best sides, but it happens that over time you start to face various problems in the operation of the remote control of your device and, most often, such problems begin abruptly, and the person does not know what happened and how to change it. The question is: what went wrong? Something happened to the TV or the remote control?

Examples of breakdowns due to which the TV remote control does not work

In addition to the fact that the remote control can completely refuse to connect and work with the TV, other problems may arise in the event of breakdowns in the remote control. For example, the remote control does not switch channels well, when you press some buttons, the equipment reacts as if other buttons are pressed. if you decide to change the channel, and instead of turning on the next one, the remote starts to increase or decrease the TV volume, etc.

The TV may respond to the remote control only in close proximity. This can be noticeable if you turn on the TV from different parts and corners of the hall. For each of the breakdowns there is a reason that causes this or that malfunction, and it also happens that at one moment several reasons converge at once, and in this case you can get a very serious problem.

Among the causes of breakdowns are:

  • Small children. As practice shows, in families with small children, it is they who cause the remote control to break down. A child unknowingly can wash the remote control in a bucket or bathroom, throw it against the wall, etc. If such a reason is identified, then the easiest and most reliable way will be to replace the old remote control with a new one and hide it away from children’s eyes.
  • Batteries. As you know, in television remote controls, energy is obtained on the basis of finger-type batteries, which are inserted into a special compartment. In order to restore the functionality of the remote control, the usual replacement of batteries or accumulators can help.
  • Scheme. The circuit of the remote control can also hide various breakdowns, ranging from loose contacts to more serious problems. A popular example of a microcircuit is the Adam24P20G circuit.
  • Quartz remote control device.
  • Buttons. The special gasket between the circuit and the buttons may become thinner.

Many problems can be detected early on, for example, by the appearance of the remote control. If you notice that the body is melted, cracked or gnawed, then this should give rise to the idea that, perhaps, there is already a problem inside, which in the future will lead to a complete refusal of equipment from work. This is how some problems can be identified and eliminated early.

Tips: how to test the remote control at home

The following are subject to verification:

  • Remote control for the Smart system. For example, it can be RMCTPF2AP1 and RMCTPH1AP1.
  • Ordinary standard remotes, for example, from Samsung. TM1050.
  • Remote controls of popular companies: LJI, Sony, Mysteries. For example, LG Magic Motion Z1025.
  • TV tuner remote control.

How to disassemble the TV remote control Samsung and 4 other firms

DIY TV remote control repair

In conclusion, the question becomes relevant. what is needed in order to check the operation of the remote control at home? First of all, watch the reaction of buttons, for example, Pairing or Select. For most models of modern remote controls, these buttons should be backlit if the device is in working order.

Examples of breakdowns due to which the TV remote control does not work

In addition to the fact that the remote control can completely refuse to connect and work with the TV, other problems may arise in the event of breakdowns in the remote control. For example, the remote control does not switch channels well, when you press some buttons, the equipment reacts as if other buttons are pressed. if you decide to change the channel, and instead of turning on the next one, the remote starts to increase or decrease the TV volume, etc.

The TV may respond to the remote control only in close proximity. This can be noticeable if you turn on the TV from different parts and corners of the hall. For each of the breakdowns there is a reason that causes this or that malfunction, and it also happens that at one moment several reasons converge at once, and in this case you can get a very serious problem.

You can get acquainted with the most popular causes of remote control breakdowns on the Internet

Among the causes of breakdowns are:

  • Small children. As practice shows, in families with small children, it is they who cause the remote control to break down. A child unknowingly can wash the remote control in a bucket or bathroom, throw it against the wall, etc. If such a reason is identified, then the easiest and most reliable way will be to replace the old remote control with a new one and hide it away from children’s eyes.
  • Batteries. As you know, in television remote controls, energy is obtained on the basis of finger-type batteries, which are inserted into a special compartment. In order to restore the functionality of the remote control, the usual replacement of batteries or accumulators can help.
  • Scheme. The circuit of the remote control can also hide various breakdowns, ranging from loose contacts to more serious problems. A popular example of a microcircuit is the Adam24P20G circuit.
  • Quartz remote control device.
  • Buttons. The special gasket between the circuit and the buttons may become thinner.

Many problems can be detected early on, for example, by the appearance of the remote control. If you notice that the body is melted, cracked or gnawed, then this should give rise to the idea that, perhaps, there is already a problem inside, which in the future will lead to a complete refusal of equipment from work. This is how some problems can be identified and eliminated early.

Tips: how to test the remote control at home

You can check the remote control at home without resorting to the help of specialists

The following are subject to verification:

  • Remote control for the Smart system. For example, it can be RMCTPF2AP1 and RMCTPH1AP1.
  • Ordinary standard remotes, for example, from Samsung. TM1050.
  • Remote controls of popular companies: LJI, Sony, Mysteries. For example, LG Magic Motion Z1025.
  • TV tuner remote control.

DIY TV remote control repair steps

Knowing the reason why the remote control broke down, you can decide what should be done to reanimate the remote control. Most often, the remote control has malfunctions, some of which can be eliminated on their own. Let’s consider a few examples of how to restore the operation of the remote control. Insufficient power supply to operate the console circuits. In this case, you will most likely need a simple battery change.

In order to properly repair the remote control, it is necessary to perform all actions in stages

There is no need to disassemble or solder anything. it is just necessary:

  • Open the console compartment;
  • Remove old batteries;
  • Replace them with new ones.

If the buttons react poorly to pressing, you will have to disassemble the device in order to check the integrity of the gasket between the buttons and the remote control circuit. Disassembling the console is a matter that requires appropriate preparations. First of all, there should be a set with small cross-section screwdrivers, both flat and Phillips, at hand. In addition, parsing the remote control will come in handy when you need to lubricate certain parts of the device.

When you know what to do, you can do it on your own. In addition, all these examples will be useful when deciding to repair the remote control yourself. But nevertheless, sometimes you should entrust this work to masters who have been repairing such equipment for several years.

TV Remote Control Manufacturers

As already noted, a house with a TV has a remote control. Each company itself develops remote controls for its equipment, which guarantees not only the appropriate quality, but also the fact that the remote control will always fit the TV that you bought. It also allows you to quickly pick up a new remote control if the old one is broken. You can pick up the necessary parts much faster if it was decided to repair the remote control yourself.

Among the main brands of TVs and remote controls, the following are the most popular manufacturers:

  • Samsung;
  • Philips;
  • Panasonic;
  • Sony;
  • Lg.

Repair of the TV remote control, as a rule, depends on the manufacturer

Samsung technology works best with Samsung accessories. In addition, there are options for the remote control for each specific model of TVs, players and set-top boxes, including those related to the Smart system. PanaSonyk, just like Samsung, develops remote control models for each new TV model created, but recently the manufacturer has been trying to create an option that will fit not only a particular type, and freely manage all new models from the company. Which, of course, will help to save money both in material terms and in the promptness of replacement.

At the very beginning of work, both the TV and the remote control usually show themselves from their best sides, but it happens that over time you start to face various problems in the operation of the remote control of your device and, most often, such problems begin abruptly, and the person does not know what happened and how to change it. The question is: what went wrong? Something happened to the TV or the remote control?

How to disassemble Samsung TV remote control: DIY repair, does not work, how to repair, does not respond

How to disassemble the TV remote control Samsung and 4 other firms

You can disassemble and repair the remote control from the TV yourself, if you correctly approach this process. TV has long become an integral part of the life of a modern person. Almost every house has at least 1 TV set, and in most cases 2 or more, depending on the number of rooms and the wishes of the household. And everyone who has such a technique knows what a remote control is. a remote control. In addition, almost half of the families have encountered breakdowns of the TV remote control and know what a remote control repair is. often than not, people underestimate the value of the remote control, so you shouldn’t. Better take some of your time to renovate.

  • TV Remote Control Manufacturers
  • Reasons: why the TV does not respond to the remote control
  • Examples of breakdowns due to which the TV remote control does not work
  • DIY TV remote control repair steps
  • Tips: how to test the remote control at home
  • DIY TV remote control repair

Reasons: why the TV does not respond to the remote control

It does not matter which company is the leader in the production of TVs, Samsung, Philips, Sony, PanaSonyk, LJI or some other company, all equipment may sooner or later fail in its work. And these failures are not only very unexpected, but also quite serious. Before you panic when the TV cannot be turned on from the remote control, you should check if the TV itself works at all?

If the TV does not respond to the remote control, then you should check the connection of the equipment to the power source

This requires:

  • First, check if the technician is connected to a power source. Even a small child can handle this. If the TV plug is connected and the current is supplied to the outlet, but the TV does not turn on, check the wire itself, it so happens that the cable from the TV to the plug is frayed, bent, etc.
  • If both the plug and the cable are in order, and there is current in the outlet, and the TV does not want to turn on, then try to start it using the button, which is located on the body of the equipment itself. If the equipment does not respond, then it is worth sounding the alarm and checking the performance of the TV itself.
  • In the case when, when turned on with the button on the panel, the TV works as if nothing had happened, and does not want to respond to the remote control, then the question arises of why this happened. Most likely, in this case, the problem is specifically in the remote control.

If repairing a TV at home is almost impossible, and experts advise contacting the masters in case of such breakdowns, then the remote control can be repaired yourself. But first of all, they must determine why the TV stopped responding to the native remote control.

DIY TV remote control repair

In conclusion, the question becomes relevant. what is needed in order to check the operation of the remote control at home? First of all, watch the reaction of buttons, for example, Pairing or Select. For most models of modern remote controls, these buttons should be backlit if the device is in working order.

Basic information on disassembling the Samsung remote

It is best to disassemble the TV remote yourself only if the device is to be cleaned. To repair badly pressed buttons and other similar faults, it is recommended to contact the service center, since experience with electronic microcircuits is required.

In most cases, parsing is carried out using a small Phillips screwdriver and a plastic card.

Any fasteners are removed with a small Phillips screwdriver, but the TV remote case is first inspected and the battery compartment checked. Only after carefully removing the fasteners to prevent the risk of damaging the remote control, it becomes possible to unscrew the microcircuit. After a complete disassembly, you can clean the keys with alcohol, since any dirt can worsen button pressing.

Touch models of television remotes require a special approach, since it is provided for the disconnection of the touch sensor located under the keyboard. Without fail, all actions are performed with particular care, because otherwise there is a risk of damage to the connecting cables.

If there are any doubts, it is advisable to contact a TV repair specialist to carry out repairs or purchase a new remote control.

How to disassemble Samsung TV remote control: tips and instructions

Situations when you need to continue to actively use the TV, but the remote control does not work well, occur quite often. In most cases, it is advisable to clean the remote control as dirt such as small pieces of food or spilled liquid will cause the remote to stop working. For cleaning, it is recommended to disassemble the device with an understanding of how this task is performed.

Instructions

Step by step instructions will allow you to understand how to disassemble the remote control from a samsung TV. Step by step actions guarantee the best result.

  • First, the back cover is detached, covering the battery compartment. After the batteries are removed, you need to unscrew the fastening bolts with a Phillips screwdriver.
  • Now you need to carefully insert the plastic card into the remote control and slightly tuck the cover. The card is carried around the entire perimeter of the console body, trying to act as carefully as possible to protect the latches from potential damage.
  • The next step is to study the mounting of the board in the TV remote control system. Screws need to be unscrewed, latches. carefully open.
  • The infrared diode is also noteworthy. If the diode is fixed, it must be carefully removed from the socket. After that, the fee goes.
  • Only at the final stage can you get the rubber buttons on the remote control by simply shaking out. If the keys do not come out, then from the front side you need to gently press the buttons and still release.

It is advisable to base your independent analysis of the remote control from any Samsung TV on step-by-step actions. Only in this case the best result is guaranteed.

Step 1

First of all, examine the remote control. whether the back cover is secured with screws. Then you need to:

  • Open the back cover where the batteries are.
  • Take out the batteries and see if there are any fastening bolts in this compartment. They are usually small and under a Phillips screwdriver.

Next. take a screwdriver and unscrew the screws around the entire perimeter.

The situation when you urgently need to switch the TV to the desired channel, and the remote control does not work well is a frequent occurrence if you do not start cleaning your equipment in time. Various contaminants are to blame. this is food, because who does not like to eat in front of the TV, and pouring liquids. from banal tea to nail polish remover. The result of all these situations is the same. we are wondering how to disassemble the Samsung TV remote control in order to clean it, because this process is not an easy matter, it requires some skill and knowledge. Now we will consider in detail how to open or open the Samsung TV remote control.

How to disassemble Samsung TV remote?

After opening the back cover, pay attention to how and how the board is attached to the remote control system. Again, if these are screws, then just unscrew them. If these are latches, then gently open them.

The rubber buttons are easy to reach. You just need to shake them out of their seats. If they do not want to leave, then you can press on them from the front side and release.

Now you can continue to do what you planned, for example, cleaning the device, because you have already managed to cope with the disassembly. And this was one of the main tasks in this process.

To further disassemble the remote control:

  • Take a plastic card and insert it into the remote control with a corner, gently tucking the cover.
  • Swipe the card around the entire perimeter of the case. be careful not to break the latches. After you have done this, you need to carefully remove the contacts for the batteries from the grooves.

Pay attention to how the IR diode is located in the socket. In most cases, it is free. If it is somehow fixed, then simply release it from the socket with extreme care. Next. get the board.

How to disassemble the Philips TV remote control?

How to disassemble the remote yourself at home? If your case is a Philips TV and you don’t know how to disassemble the Philips TV remote control? You don’t have to go far, since the remotes of all brands of TVs are almost identically assembled at the manufacturing plants. Therefore, if you use our tips above how to disassemble the Samsung TV remote control, then you will not make mistakes and will successfully carry out this manipulation.

How to choose a remote control for your Samsung TV

There are several options for selecting a remote control for Samsung TV:

In this video, you will learn more about this remote control:

There are also a large number of universal remote controls that fit a wide variety of TVs. The operation of this device is based on capturing a signal from a TV and playing back the same. A big advantage of such remote controls is the ability to record multiple signals. Thanks to this, using this device, you can control several TVs or other technical means at once. If this is not done, other devices may react to the signal from the remote control.

On the phone

Samsung TVs from the N, M, Q, LS, K, J and F series are equipped with Screen Mirroring. It allows you to connect your phone to your TV. This function provides mirroring of the smartphone screen to the TV, and also makes it possible to control some TV functions using a mobile phone.

Repairs

The remote control is actually very fragile, and only people who have experience in repairing various microcircuits need to repair it. The first step is to determine if your model of device can be repaired at all. The phone camera can help you determine if an infrared signal is being emitted from the remote control. If there is no such signal, then the device does not function and it is necessary to replace it or repair it.

In most cases, the problem is that various keys on the remote control stick or partially do not work. This can be caused by a malfunction of the graphite deposition, which performs the function of a conductor. To restore performance, you must perform the following steps:

  • Parse the remote control according to the instructions;
  • Cut the aluminum foil into small square pieces;
  • Then you need to glue these pieces to the contact surface;
  • Assemble the remote control in reverse order.

Also, the remote control often does not work, because the ceramic quartz is broken. The most common reason for the remote control to stop working is when it falls from a height. The first sign of this malfunction is the appearance of an extraneous, rumbling sound when the remote control is shaken. In order to restore the normal operation of the device, it is enough to replace the ceramic base. Do not forget that the remote control, like other equipment, requires regular maintenance. To increase the service life of this device, you need to periodically disassemble and remove dust from the inside of the console.

Settings

Regular push-button remote controls that come with Samsung TV do not require special setup. The instruction for operating the buttons is attached along with other documents to the TV. Since 2012, TVs have been equipped with Samsung Smart Controls. It provides control of the TV, as well as the set-top boxes that are connected to it. This remote control is also equipped with a voice control system and automatic locking. You should be attentive to the last function and immediately read the instructions on how to unlock the Samsung TV remote control.

When you turn on the TV for the first time, the Samsung TV should be paired and configured automatically. Please note that the device needs to be charged. If there is no automatic connection, you need to hold down the two buttons located to the right and left of the “Play” button for 3 seconds. Then follow the application in the book and set up TV.

Universal remote controls require special setup. When buying a device of this type, the seller must give you an application for connecting the remote control. There are a large number of universal devices for controlling TV, as a result of this, there are also many ways to configure the connection. We will cover two main options.

The first method is available if the remote control contains the keys of the main TV manufacturers. You need to select the “Samsung” key and the remote control should quickly connect to the TV. It is worth noting that it is necessary to turn off extraneous digital devices located near the TV in order to avoid any interference. At the moment of pressing the button with the TV brand, it is necessary that the TV is turned on, and the remote control is directed to the front panel of the screen. You must hold down this key for several minutes until some action occurs on the TV screen.

Don’t forget to set up the remote correctly

Second way. You can set up the connection by following the instructions for the remote control, which should be in the box of the device. On it you will find a large number of numbers. these are codes. They are required to pair the remote control with the TV. To start setting, install batteries in a special compartment of the device and press any keys. The indicator light located at the top will give certain signals when you press the keys. After that, find in the instructions the necessary numbers corresponding to the firm of your TV. The next step is to point the remote control at the TV and long press the power key. After a while, the lamp should light up, after which you should enter the digital value of the corresponding code. After that, the remote control should be paired.

Connection

Synchronizing the universal remote control is easy enough. Each manufacturer provides instructions for such remote controls, which must be read before connecting the device. This type of remote control is used by people who do not like standard devices. The user chooses a universal device independently, depending on the preferences of the appearance, price and functional equipment. Instructions on how to bind the remote control to the TV are supplied with the device itself.

Remote Control for Samsung TV

The remote control plays a very important role in watching TV. With its help, all operations are carried out: setting up channels, images and sound, enabling various functions and many others. The TV can be controlled using the original remote control or a universal device.

How to disassemble the remote

Experienced craftsmen advise not to carry out repair work to people who have not previously had experience in repairing microcircuits. In such cases, it is easier to contact the service center, where they will carry out high-quality equipment repairs for a fee. If you start repairing the remote control yourself and spoil it, the cost of buying a new product can be much more expensive than repairing it at a service center.

First, you need to look at the instructions on the Internet on how to disassemble the Samsung TV remote control. To disassemble the remote control, you need a small curly screwdriver and a plastic card. First of all, you need to inspect the body for the presence of bolts. Most often they are located in the battery compartment. Since they are small in size, you can unscrew them using a small screwdriver. In order to get to the remote control microcircuit, it is necessary to gently press on the surface of the case, and hold the plastic card between the two main parts of the remote control. Be careful not to damage the edges of the remote control.

Don’t forget about the parsing screwdriver

After you have removed the front panel with buttons, you need to disconnect the spring located in the battery compartment. Then you can inspect the microcircuit. If this part is burned out, then it is necessary to purchase a new remote control, and not a separate microcircuit. Also, the masters are not advised to disconnect the sensors from the microcircuit.

There is a variant of remote controls, which are fixed using special glue. If it is present, but the analysis needs to be done very carefully. This type of remote control can be opened with a flat screwdriver or a mild kitchen knife. We set the console in a horizontal position and, using the selected tool, which is inserted between the two main parts of the console, we produce ajar cases. This procedure must be carried out around the perimeter of the entire building. After you have opened the remote control and fixed the malfunction, you must also use special glue to close the remote control. Important! It is necessary to apply the glue evenly, since small gaps can cause dust and moisture to enter the device, which in the future may affect its performance.

To repair the touchscreen remote control, you must use an appropriately sized screwdriver. You also need to disconnect the touch sensor located below the keyboard. Dismantling the screen is carried out with increased accuracy to avoid damage to the connecting cables. However, manufacturers and craftsmen strongly advise in the event of a failure of this type of remote control to contact specialized service centers.

Cleaning

To completely clean the remote control from dust, it is required to remove the buttons from the front panel, which is carried out by pressing the buttons on the push side. Cleaning must be done to avoid sticking keys in the future. The tools for this operation are wipes and alcohol.

These numbers are necessary for pairing and setting up universal remote controls with various devices. DVD players and TVs. Each brand and each type of device corresponds to a certain digital combination, which is indicated in the instruction manual of the remote control.