How to Connect a Receiver to a TV

How to Connect a Receiver to a TV

The whole world has long switched to digital television. Our country began the process of transition from analog signal transmission relatively recently. Digital television has contributed to the emergence of digital channels broadcasting throughout the country. TVs that support digital broadcasting DVB. T 2 appeared on sale.

This is very convenient, just connect the television cable to the TV, while no other wires are needed. However, if the TV does not support digital broadcasting, here the digital set-top box comes to the rescue. Many people who purchase this device do not know how to connect it to a TV. Therefore, it is necessary to fill this information gap.

Equipment required

In order to broadcast digital television in the apartment, the following equipment is required:

  • TV;
  • Receiver;
  • Antenna or satellite dish.

The TV should be such that it has an input for the antenna, connectors for “tulips”, scart. An input with a video input. Modern TVs have an hdmi connector, it is also suitable for connecting a receiver.

Before you purchase a set-top box, you must familiarize yourself with the list of companies that provide digital television broadcasting services. Can consult with specialists the chosen company, who will advise the necessary model of the receiver. Some companies hold promotions that allow you to purchase and install the device for free.

The set-top box itself is just an attribute that allows you to receive and tune channels for a specific TV broadcast in a completely new format and much better quality. So that they broadcast through the receiver, you should deal with the broadcast source. It could be:

  • The Internet;
  • Satellite dish;
  • Other similar items.

How to connect a digital set-top box

Connecting the console to the TV is as follows:

  • It is necessary to unpack the TV set-top box and remove the protective film from it. This is done so that the film does not heat up during the operation of the console.
  • The cable is taken and the protective sheath is cut off from its ends, retreating by 10. 15 mm. The sheath must be cut so as not to accidentally damage the shiny film protecting the center conductor. Such a film is shielding.
  • Carefully unbend the film and screw on the f. Connectors.
  • Then connect the set-top box cable to the TV.
  • After that, wire the tulips to the console and the TV.
  • At the end, an antenna is connected to the TV. Install the antenna on the outside of the house or on the balcony. In this case, it is necessary to ensure that the antenna does not interfere with the wires of the power line or tree branches.

After that, it remains only to configure the digital receiver.

Setting up a digital set-top box

Set up a digital set-top box as follows:

  • You should take the console’s remote control and press the “Menu” button;
  • A window appears in which you need to select the “Configure channels”;
  • Press “OK” and wait until the prefix automatically tunes in the channels;
  • Then you need to accept the discovered channels and save them.

Thus, setting up the receiver is quite simple.

Connecting a digital device to an old TV

Many still use old TVs. If the prefix attaches to modern models quickly and easily, then old “electrons” do not have a connector for “tulips”.

Some older televisions do not have an A / V input, but they do have a SCART connector, some of which receive component signals. Therefore, you can yourself find the adapter circuit “tulips” on SCART and solder.

In addition, you can purchase an adapter from audio-video to SCART. It is of two types: adapter cable and adapter itself, to which they connect a standard RCA cable from the console.

Old Soviet TVs of the Electron type are completely not equipped with any inputs, so use only the antenna jack, where a high-frequency modulated signal is supplied. Thus, it will be necessary to find a modulator with RCA inputs.


Having connected a digital television, do not forget to pay every month for a certain package of channels. Some providers offer the purchase of digital set-top boxes with a set of digital TV channels, which are already included in the price.

The main thing is from time to time to be distracted from watching your favorite TV shows in order to devote time to your family.

Video: How to Connect a Receiver to a TV

When you purchase the receiver from many, especially from inexperienced users on this issue, the question immediately arises: “how to connect the receiver to the TV?”. A large number of connectors and various wires are puzzling and even annoying, but, oddly enough, you can learn how to connect the receiver to a TV without the help of a specialist.

First you need to understand what we are dealing with: a receiver is a device that is designed to receive and convert various digital, analog, video, audio, and radio signals. It allows you to convert several signals, redirect them to the appropriate display system (video or audio), thanks to this device you will get rid of the awesome web of cables in your home.

Why so many connectors?

Of course, a receiver with a convenient and simple interface with a small number of connectors would be very simple and convenient to use. Yes, and connect it would be easy. For example, the presence of only one modern HDMI interface transmitting digital video and audio signals used for all modern technology would be more than rational. But after all, not everyone has the latest TV models in the house, there are quite “ancient” products that their owners do not want to part with. Here the connection diagram changes, and completely different connectors are needed, which, oh, cheers. Are provided in the purchased receiver.

Of course, there are many nuances that affect image quality. It can be affected by: the quality of the original signal that the receiver received, and the quality of the interface of the device that converts the received signal. Therefore, the choice of the receiver interface must proceed thoroughly and choose the most optimal type of connection.

Types of connection and data transmission, their purpose

RCA (tulip)

The RCA (tulip) interface created by Radio Corporation of America has a long history, and for a long time it was it that was the only one of its kind to connect and transmit data to a TV.

It has a triple of connectors, marked in white, red, and yellow. Colors indicate respectively. Left (white) and right (red) audio channels, and video channel (yellow). After finding these connectors, you should connect the device to the TV, connecting Video IN with Video OUT according to the color coding.

Among the disadvantages of this interface is the inability to deliver a high-quality digital signal, so the TV will display a fuzzy picture with noise. Therefore, the choice of RCA (tulip) should be preferred only if your TV has a small diagonal screen.

S-Video Connector

S-Video connector, whose presence is mandatory on DVD-players or game consoles, but, interestingly, not every TV is equipped with it.

Unlike RCA, this receiver jack provides the user with better signal quality. In addition, the frequency of the signal is higher, therefore, the image is more clear and colorful.

But in order to transmit an audio signal, you must connect a separate cable.

SCART Connector

The SCART connector, which is also called the “comb”, is more versatile than previous versions. To connect, use the appropriate cable connecting the TV and receiver.

The signal quality meets many requirements, there is also support for RGB, S-video, and stereo sound.

RF connector

An RF connector that allows you to connect a television antenna or cable television. It is not very high quality signal transmission. But in case you want to use a small mobile TV, this connector is perfect.

Also, this interface allows you to connect two television devices to one receiver at once. But to accomplish this task, the receiver must have a high-frequency RF modulator and a corresponding connector.

YPbPr and YCbCr Interface

The YPbPr and YCbCr interface delivers high-frequency video through three cables. They are called “component” and allow you to get a signal of high accuracy and quality.

The main difference between YPbPr and YCbCr lies in the systems in which they are used. YCbCr is digital, and YPbPr is analog.

Now more about cables:

All three cables are painted in various colors: green, red, and blue.

The green color of the cable means that it is responsible for transmitting the brightness level and clock pulses to the TV.

Red will convey the difference between two levels: red and brightness.

Blue. Respectively: the difference between brightness and blue level.

The audio signal is transmitted (if you want to play audio through the TV’s audio system) using a separate RCA connection (white. Left channel, red. Right channel).

HDMI is the most versatile and modern type of connection. A receiver equipped with this interface is capable of transmitting and converting a digital signal into high-quality video and image clarity. By transmitting various content, HDMI is suitable for TVs with a large diagonal, and provides the ability to connect HD equipment. In addition, the HDMI interface allows you to simultaneously transmit video and audio digital data.

In order to connect the receiver’s HDMI connector to TV technology, you need only one cable of this type, which greatly simplifies the task of finding the desired input.

Decide on the choice

This review of the receiver’s interface is made so that the buyer can determine the versatility and necessity of each type of connection, and can choose the best option suitable for his TV.

  1. In the first position is the HDMI interface with its high quality signal transmission and the only wire for transmitting both video and audio stream.
  2. The second place is occupied by component analog and digital outputs. YсbСr and YPbPr.
  3. The third position goes to the SCART interface.
  4. Then follows S-Video.
  5. Fifth place is the “discoverer” of RCA (tulip).
  6. And in the last position. An RF connector that allows you to connect the TV to the antenna.

In accordance with these data, you can select the appropriate receiver interface, which is suitable specifically for your equipment and ensure stable operation of the devices.

About connecting

When connecting a TV to the receiver, you need to use several basic rules:

  1. Disconnect the connected devices from the power supply network;
  2. Carefully read the instructions;
  3. Follow the sequence of actions;
  4. Use short cables whenever possible.

Excessive initiative is not required, because everything has its own instructions that must be followed. The length of the cables is also important: the quality and stability of the transmitted image and sound to your TV directly depends on their length.

And before starting the device, you need to check the correct connection of each cable, and only then turn on the equipment.

We advise you to read: how to connect two TVs to one antenna, how to connect speakers to a TV