How to connect a D Link router to a computer

Connecting the router to a computer or laptop via a network cable. Instructions for dummies

In this small step.By.Step instruction “For dummies”, I will show how to connect a router to a computer using a network cable. If we are talking about a laptop, then he must have an Ethernet port. If it is not, then you can make a connection via wi-fi. In the future, there are two ways to configure the router-through the web-intense control panel or using the utility on CD. I will disassemble the connection of routers on a network wire using the example of TP-Link TL-WR740N and TL-WR741ND, but this guide is suitable for any model.

The first option to connect the router to the computer. Using a network cable, which lies in a box in a set of any device of this type. Typically, a stationary PC does not have a wireless module, so it is advisable to connect it with a wire.

We take out the Internet pipeline, which was previously inserted directly into the computer, and connect it to the port of the router, which is marked as Wan. Often it has a color that differs from others. What to do if the wire is not determined in the router, read separately.

Next, we take Ethernet cable with two free ends out of the box of the router. On one side, we insert PC into the network connector. Where the wire from the provider used to go, which you were brought into the apartment when connecting the Internet. It is located on the rear panel of the computer housing. On a laptop, you need to look for it from behind or from the side

We connect the other end to any of the several LAN ports on the router. They are indicated by numbers and are also often marked with one color.

D-link, entrance to the router: Preparing the device for settings

If we are talking about setting up only a purchased router, first of all, the device must be taken out of the box. Then the antenna should be connected to the device body. Now we connect the provider’s cable to the router connector, which is indicated by the “Internet”, connect the computer’s network board to the router, installing the plug in the port signed as “Lan”. We insert the cable from the power supply into the device supply nest and connect to the network.

Now you need to perform some settings in the computer. We do everything in stages:

  • We go to PC in “Start”.
  • Now you need to open the “control panel”.
  • In the menu, select “Network and the Internet”.
  • Then it is necessary to enter the “Center for Control of Networks and General Access”.
  • Click “Change the parameters of the adapter”.
  • We will be interested in the item “Connection on the local network”.
  • Call the menu mouse with the right key.
  • Choosing “properties”.
  • Click on the “Protocol 4 (TCP/IPV4)” and put a mark at the “Receive IP automatically” and “Get DNS automatically” item.
  • We confirm the actions performed by clicking “OK”.

D link router setup with in 5min in Telugu

If you plan to work with the former use by the router, we recommend that you first drop the settings to factory parameters. To do this, take the device in our hands and find on its case a special button signed as Reset. Since the button is drowned, you need to take any sharp object, for example, a pin or a clip to press this button. Hold it for about 10 seconds. Then the device is resetting all the settings, and you can re.Set the desired parameters.

D-Link router setup for Beeline, Rostelecom or other Internet provider

In the next step of the D-Link router settings, you need to select the type of your connection to the Internet. There are simply fantastically many different options. Frankly, I have not seen such an amount on any model, there will be for any occasion.

connect, link, router, computer

What kind of Internet type you have, you need to find out from the provider. But in your contract for the provision of services, everything should be spelled out. The type of connection and data for access.

connect, link, router, computer

To configure the D-Link DIR-300 router for Beeline (DIR-615, DIR-620, DIR-320 or any other model), you will need to choose L2TP-it is this technology that Beeline uses it. In this case, it will be necessary to indicate the server for connection, the login and password provided by the provider.

See also  How to connect a computer to a modem via cable

PPPOE

If your type is pppoe, then login and password are required. This type often uses Rostelecom

Setting up Internet connection

If you incorrectly configure the connection to the provider network, the device will not distribute Internet. To do everything right, you need to know what type of connection the provider used has. This information can be clarified by the supplier.

To quickly tune in and not waste time, it is advisable to find out if the operator is binding on the MAC address. If the provider has a dynamic IP (without a MAC boost), the network will appear immediately after turning on. In this case, in the settings, the connection status will be highlighted in green. Therefore, it can be proceeded to the next stage. Consider how to configure a router from D-Link when binding Mac. In this case, there are two options for solving the problem:

  • Independently reconfigure the address of the router to the MAC laptop or PC, to which the Internet is tied;
  • Contact the operator and ask to tie the address of the new device.

MAC address is indicated on the rear panel of the router. It can be found and copy in the Wan tab.

For configuration, you need to enter the “Network-Wan”. Having set the boxes opposite the existing connections and remove all the excess. Next, add the desired type of connection. Beeline uses the L2TP connection protocol. T transgress (TTK), Rostelecom and House.Ru PppoE connection type. Having decided on the protocol, you need to open the appropriate tab and dial the login and password twice. Some providers also need to fill in the column “VPN server”. In the settings, you need to set a checkplace opposite “connect automatically” and click “apply”. If everything is done correctly, the connection and the green icon will appear.

PPPOE connection

Set up a router with the fact that a new connection is created. Next, PPPOE is selected. This type is used by such operators:

The next stage. You need to specify the password with the login. Information can be viewed in the contract with the provider. Also on the official sites of most providers you can find step.By.Step instructions on setting up routers written in language, understandable even for dummies. After this data is entered, you need to click “apply”. If the network does not appear, it is better to contact the provider and clarify the data.

Connection of the router D-Link Dir 300 to a computer

Connection, in general, usual, for this type of router. By the way, models of routers 320, 330, 450 are similar in settings with D-Link Dir 300 and are not much different.

How to setup dlink router on pc in Hind | D-link router ka first time setup kaise kare hindi jankari

The first thing you do is connect the router to the computer. The wire from the entrance, which used to be connected to the computer network card. Connect to the Internet connector. With the help of a cable that comes with a router, connect the exit from the computer’s network card with one of the local ports (LAN1-LAN4) D-Link Dir 300.

The picture shows a cable (left) to connect a computer and router.

On this actually all. Yes, by the way, pay attention to whether the LEDs flash on the router’s case (if everything is fine, they should blink).

Connection of the router D-Link DIR-300 to a computer

The next step will be the connection of the router D-Link DIR-300 to your laptop or personal computer. To do this, you need to connect the cable that the Provider to the port of the router, where the Internet was signed, in older models, this port is signed as “WAN”. The cable that came with the router, connect one end to the laptop or computer, connect the other end to one of the four ports, which are indicated in black on the router (ports of the ports may differ depending on the route version). And yes, don’t forget to connect the power cable.

D-Link Dir-320 router setup.

And finally we got to the router of the router and now you need to set up equipment. First, we protect the wireless network by installing a password on Wi-Fi. Then you will need to find out what type of connection is used to enter the Internet is PPTP, L2TP or PPPOE. You can find out by calling your provider (this is the organization with which you have concluded an agreement to provide the Internet service). So, let’s start setting up the router. To begin with, we change the language of the web-intese to Russian. To do this, go to the “Language” tab and choose “Russian”

See also  How to turn on the front flash on Android

Setting a password on Wi-Fi on a D-Link DIR-320 router.

I bring to your attention video instructions for setting a password on Wi-Fi on a D-Link DIR-320 router using the D-Link Dir-620 router.

Let’s also take a written password setting up a Wi-Fi password on a D-Link Dir-320 router in writing and illustratively. One. Choose on the Web-Inteiis “Expanded Settings” 2. In the “Wi-Fi” menu, select “Basic Settings” item.

Check “Turn on the wireless connection”, there should be a checkbox. 4. Below in the line “SSID:” To invent and indicate the name of your wireless network, this name will glow in the future when you will connect to the network. 5. “The country”. “Russian Federal,” channel “. “Auto”, “wireless mode”. “802.11 b/g/n mixed “. 6. Click “apply” and return to the previous menu by pressing a symbol similar to the triangle on the left.

In the “Wi-Fi” menu, select “Safety Settings”.

In the line “Network Authentication:” Select “WPA2-PSK”. Nine. In the line “PSK encryption key:” You need to come up with and drive a password for the wireless network, which we created above. Ten. Click “apply”, then in the right upper part of the Web-Intease we go into the “System” tab and click “Sokhr. And restart “.

PPTP setting on the D-Link DIR-320 router.

I bring to your attention video instructions for setting up the type of connection of PPTP on the D-Link DIR-320 router using the D-Link DIR-620 router.

Let’s also consider the PPTP connection setting on the D-Link DIR-320 router in writing and illustratively. One. In the “Network” menu, select “Wan”.

In the window opened, click “Add”.

In the paragraph “Type of connection:” Select “PPTPDYNIMIC IP”. 4. Put a checkmark opposite “connect automatically”. 5. Below we drive the user name (in the line “User name:”), password (in the line “Password:”), confirm the password (in the line “Password confirmation:”) and indicate the address of the server (in the line “VPN server address:”). All of the above data is provided to you by the provider (the organization that has conducted the Internet to you). All these data are usually prescribed in the contract with the provider. If for some reason you could not find them, you need to call a hot fishing line for the trimmer of your provider and find out how you can get them. 6. After all the manipulations with the settings, click the “Apply” button.

In order to save all the settings, it is necessary to go to the “system” tab in the upper right part of the Web-integer and press the Sistema. And restart “.

PPTP setting with a static IP address on the D-Link DIR-320 router.

Consider the PPTP connection setting with a static IP address on the D-Link DIR-320 router. Typically, a static IP address is provided to legal entities, or as an additional service for the main tariff for individuals. One. In the “Network” menu, select “Wan”.

connect, link, router, computer

D-Link Dir-615 router settings.

And finally we got to the router of the router and now you need to set up equipment. First, we protect the wireless network by installing a password on Wi-Fi. Then you will need to find out what type of connection is used to enter the Internet is PPTP, L2TP or PPPOE. You can find out by calling your provider (this is the organization with which you have concluded an agreement to provide the Internet service). So, let’s start setting up the router.

I bring to your attention to watch a detailed video instruction on setting up the router D-Link DIR-615:

Setting a password on Wi-Fi on a D-Link DIR-615 router.

We select the Wireless Settings tab on the Web-Inteatheis, then “Manual Wireless Connection Setup”.

In the item “Wi-Fi Proteded Setup” remove the checkmark on this setting: “Enable”. 3. Below in the line “Wireless Network Name:” To come up and specify the name of your wireless network, this name will be glowing in the future when you will connect to the network. 4. Below we will choose “Security Mode:”. “Enable WPA/WPA2 Wireless Security”. 5. Below in “Network Key:” Invent and drive a password. 6. After click “Save Settings”.

PPTP setting on the D-Link DIR-615 router.

We go to the menu to the Internet tab, then “Manual Configure”.

In the item “My Internet Connection is:” Select “Russia PPTP (Dual Access)”. 3. Below you will be offered to indicate the server IP address in the line “Server IP/Name:”, the user name in the line “PPTP Account:” “, Password in the line” PPTP Password: “And the password confirming the line” PPTP RETYPE PASSWORD: “. All of the above data is provided to you by the provider (the organization that has conducted the Internet to you). All these data are usually prescribed in the contract with the provider. If for some reason you could not find them, you need to call a hot fishing line for the trimmer of your provider and find out how you can get them. 4. Put the checkpoint “Connect Mode Select:”. “ALWAYS-ON”, this setting will keep the Internet connection constantly. 5. After all the manipulations with the settings, click the “Save Settings” button.

connect, link, router, computer

PPTP setting with a static IP address on the D-Link Dir-615 router.

Consider the PPTP connection setting with a static IP address on the D-Link DIR-615 router. Typically, a static IP address is provided to legal entities, or as an additional service for the main tariff for individuals. One. We go to the menu to the Internet tab, then “Manual Configure”.

See also  How to connect IPTV to TV

In the item “My Internet Connection is:” Select “Russia PPTP (Dual Access)”. 3. Below you will be offered to indicate the server IP address in the line “Server IP/Name:”, the user name in the line “PPTP Account:” “, Password in the line” PPTP Password: “And the password confirming the line” PPTP RETYPE PASSWORD: “. 4. Put the checkpoint “Connect Mode Select:”. “ALWAYS-ON”, this setting will keep the Internet connection constantly. 5. Since the connection uses a static IP address, set the “Static IP” 6. We indicate the IP address in the line “IP Address:”, the subnet mask in the line “Subnet Mask:”, the main gateway in the line “Gateway:” And DNS in the line “Primary DNS Address:”. All of the above data is provided to you by the provider (the organization that has conducted the Internet to you). All these data are usually prescribed in the contract with the provider. If for some reason you could not find them, you need to call a hot fishing line for the trimmer of your provider and find out how you can get them. 7. After all the manipulations with the settings, click the “Save Settings” button.

L2TP setting on the D-Link DIR-615 router.

We go to the menu to the Internet tab, then “Manual Configure”.

At the point “My Internet Connection is:” Select “L2TP”. 3. Below you will be offered to indicate the server IP address in the line “Server IP/Name:”, the user name in the line “L2TP Account:”, password in the line “L2TP Password:” And the password confirming the line “L2TP RETYPE PASSWORD:”. All of the above data is provided to you by the provider (the organization that has conducted the Internet to you). All these data are usually prescribed in the contract with the provider. If for some reason you could not find them, you need to call a hot fishing line for the trimmer of your provider and find out how you can get them. 4. Put the checkpoint “Connect Mode Select:”. “ALWAYS-ON”, this setting will keep the Internet connection constantly. 5. After all the manipulations with the settings, click the “Save Settings” button.

Detailed instructions for setting up the router D-Link DIR-300

To start the D-Link DIR-300 settings, start the browser and enter it in the address line http: // 192.168.0.1 in order to get into the web-integrate router.

If you can’t get into the administrator’s panel, then check the settings for the installation with the router on the PC itself. About how to do this, I wrote in detail here.

At the first entrance, we will be asked to introduce a couple of login-paralle-by default “Admin/Admin”. This is standard data not only when connecting to the D-Link Dir router, but also for the vast majority of other models.

Internet connection and Wi-Fi

We find ourselves on the main page of the personal account D-Link DIR-300. We need to open the section “Extended settings”. A link to it in the lower right corner.

Here, for starters, let’s configure the connection of the D-Link router to the Internet. Open the “Network” tab, section “WAN”. Choose the type of our connection. It is indicated in the contract with the provider, find it and look, or find out in technical support. After that, enter all the data provided in the contract and the required data for the connection.

I have a type. Pppoe, for which only login and password are needed for authorization. We leave the rest of the fields by default if the provider does not require other.

Further, the setting of the router D-Link DIR-300 continues to enter data for a local wireless network, that is, for those computers who will go to the Internet through it. First of all, we will make sure that Wi-Fi is turned on-you can do this either right on the main page of the admin panel in the Wi-Fi block-just switch the slider.

Or go to the “Basic Settings” and activate the “Turn on the wireless” show.

Denial of responsibility | Contacts |RSS | SE | EN | BR | DE