Error E2 Samsung

Dishwasher error codes

Aeg dishwasher error codes

Fault coding is accompanied by a corresponding indication

1 blinking i10 there is no water supply, while the dishwasher is running, the water access from the central water supply may have been blocked. Also check the dishwasher inlet filters and the integrity of the water filling hoses.

Error E2 Samsung

2 flashes i20 does not automatically drain water from the dishwasher chamber

3 flashes i30 overflow fuse activated

5 flashes i50 a short circuit has occurred, which disabled the triac of the circulation pump

6 flashes i60 Water heating failure, temperature sensor faulty

7 flashes i70 NTC contact is open or short circuit

8 flashes i80 Loss of signal, no contact with external EEPROM memory

9 blinks i90 code indicates that an incorrect checksum of MCF or CCF encodings has been received

10 flashes iA0 the water supply is blocked or water access to the dishwasher is limited

11 flashes ib0 transparency sensor failure

12 blinks iС0 communication error with user display

13 flashes iАd0 Communication with the tachogenerator is broken, but the pump is working

14 flashes iF0 Water filling timer failure

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Ardo dishwasher error codes

E1. The aquastop water leakage protection system has turned on, it is necessary to check the hoses and their attachment to the dishwasher

E3. The dishwasher has automatically overfilled and the security level has been activated.

E4. It is not possible to heat the water, the temperature sensor may be faulty or its readings are erroneous

E5 there is no water in the cooking chamber, the supply valve may be closed or the inlet hose disconnected

E6 error in the drain process, most likely the drain hose is pinched or a blockage has formed in the filter of the machine or in the water drain.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Ariston dishwasher error codes

A01 in the dishwasher the Aquastop function has worked, the hose may have been disconnected from the device, it is necessary to check the fastening of the hose

A02 the electrical circuit reports an error, the heating element may be faulty or the temperature sensor is out of order, or a short circuit has occurred in the circuit

A03 the drain system has timed out, it is necessary to check the fastening of the hoses in the drain system

A04 error in the sensor of filling the tank with water, as the system received a message that after a certain amount of time specified by the program, the required water level was not reached

A05 there is no signal from the temperature sensor of the TENA protection against overheating

Al06. The error is associated with a circuit power failure from the SV filler valve. With such a problem, a bay valve malfunction occurs, the level sensor is in a closed position.

Al07. This error is not used

Al08 is an error resulting from problems with the NTC temperature sensor. This error occurs due to exceeding the permissible water heating time.

Al09. This error is related to software recognition problems. In this case, the keyboard is faulty.

A10 dishwasher filling valve error code, a short circuit may have occurred. For some models of dishwashers, this code indicates a malfunction of the temperature sensor.

A12 water heating system error, temperature sensor may be defective

A13 an error occurred in the dispenser, or a short circuit occurred in the control system, which led to a device malfunction.

A14 error of the drain hose, most likely its location is too low, which triggered the appearance of a siphon effect. Check the drain hose and correct the problem by repositioning and following the instructions.
H20 problems with the water supply, which indicates both a complete lack of water, and very low pressure in the central line, and may also indicate a malfunction in the filling valve.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Asko dishwasher error codes

F1 heating circuit error, possibly one of the dishwasher temperature sensors is faulty

F2 code informs about the presence of too much water in the dishwasher tank, due to which the overflow sensor has been triggered

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Bauknecht dishwasher error codes

F6 E2- The water tap is closed / no water flows into the dishwasher.

During operation, the crane must be open.

F6 E7 or F6 E1. Low water pressure. In the process of using the dishwasher, the water pressure from the tap must be maximum (the minimum allowable flow is 0.5 l / min). An error can also result in a kinked hose or a blockage in the dishwasher chamber filter.

F6 E3 / early completion of the dishwashing (while the contents of the dishwasher remain dirty) A similar error occurs when a blockage occurs in the dishwasher filters. In the absence of these problems, it is worth checking the correct installation of the dishwasher drain hose. Finally, excess foam in the machine can be the cause of the error. It is necessary to check for the indicated malfunctions, if found, correct for further operation of the machine.

F8 E1. The error appears if there is a blockage in the filters of the dishwasher. In this case, the filters must be thoroughly cleaned. Another cause may be a kinked hose, which is responsible for draining water from the dishwasher. Finally, a blockage of the junction with the siphon hose can occur. In this case, you should dismantle the disc covering the joint.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Beko dishwasher error codes

0000- there is no water supply to the dishwasher, the supply hose may be blocked or the pump is faulty

000. No water heating, temperature sensor is faulty.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Bomann dishwasher error codes

E1 Increased filling time Taps are not open, or water intake is blocked, or water pressure is too low

E4 Overflow. Some parts of the machine are leaking

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Bosch dishwasher error codes

E1 if the machine gives you such an error code, it means that the water is not heating. Elimination is fast. It is necessary to check and eliminate the problems of the thermostat, heating element or water sensor.

The E2 code is a problem with the level sensor. This means that the water resistance should be approximately 50KΩ.

E3 this code is associated with a breakdown of the water intake. Also, this error is eliminated by checking the status and eliminating defects in the pump, NTC sensor or inlet valve.

E4 is an error code indicating a breakdown of the flow switch. Its elimination should be started by inspecting the sensors and its electrical circuits.

E5 code means that the level of the permissible amount of water has been exceeded. This problem occurs when a valve or level sensor is faulty.

E6 error, which indicates a breakdown of the aquasensor.

E8 code associated with insufficient amount of water that is in the pan. This error can be easily eliminated, it is necessary to increase the water filling pressure.

E9 are problems associated with a breakdown of the heating element.

E11 this code indicates the absence of water heating.

E14 is a problem associated with the operation of the water flow sensor.

E15 code that indicates an aquastop error, perhaps the function is currently disabled or there were some problems with its activation

E16 automatic water intake, the water intake sensor may not work or the contact wire is broken

E17 problems associated with water filling, which is possible as a result of a faulty hose or its kink, clogged inlet filters of the dishwasher. You should be aware that the operation of the machine does not imply a deformed position of the hose, as well as the presence of blockages at the junction with the water tap. Straighten hose and / or clear blockage in pipe

E18 this code indicates the automatic end of the program after draining the water.

E21 error of malfunction in the operation of the water pump.

E24 is a code that indicates problems with water draining.

E27 low voltage problem.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Brandt dishwasher error codes

E1 signal that the water supply pressure is too low, the pressure in the central line may be lowered or the inlet hose of the dishwasher is clogged

Light codes of malfunctions:

The Quick wash mode indicator flashes rapidly. Means that the water intake period is too long, perhaps the supply taps are not open, the water supply is completely absent or the initial water pressure is too low

The Eco indicator is flashing. The dishwasher tank is overfilled, too much water is supplied

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Candy dishwasher error codes

E1 problems with the water filling process. The required level set by the corresponding program has not been reached after the specified time.

E2. Problems with water drain. The water was not completely drained after the time set by the washing program. 4 minutes after the start of water draining

E3. Problems with reaching the required water temperature for washing dishes

E4 the Aquastop system automatically turned on

E5 open circuit of the NTC temperature sensor or its malfunction due to a short circuit in the system circuit

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Electrolux dishwasher error codes

End indicator signal code and additional information code

1 signal i10 Problems with water filling: check the water pressure, as well as the position of the hose, the possibility of clogging

2 signals i20 Problems with water drainage: it is necessary to check the position of the hose, the possibility of clogged filters

3 signals i30 The overflow fuse is automatically activated

5 signals i50 there is a short circuit of the triac, which is responsible for the functioning of the circulation pump

6 signals i60 water heating failure, there is a possibility that the temperature sensor is faulty or its readings are incorrect

7 signals i70 Open circuit of NTC temperature sensor or short circuit of the system.

8 signals i80 Failure in sending / receiving signal, problems with communication with external memory EEPROM

9 signals i90 Error in checksum MCF or CCF

10 signals iA0 Problems with filling the machine with water: check the water pressure, as well as the position of the hose, the possibility of clogging / clogging of filters

11 ib0 signals Problems with the water transparency sensor in the dishwasher

12 signals iС0 Communication failure with user display

13 signals iАd0 Communication failure with the tachogenerator, while the pump is functioning properly

14 signals iF0 Problems with the water filling timer

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Fagor dishwasher error codes

F1 water drain error, acquastop option activated to prevent water leakage from the drainage system

F2 error of the system for determining the water level in the working chamber of the dishwasher.

F3 a malfunction of the heating system heat sensors is detected

F4 malfunctions in the water temperature detection sensor circuit

F5. No water filling or this operation is performed incorrectly.

F6. Malfunction in water drain. Water is not drained or operation is incorrect

F7 error or malfunction in the operation of the turbine, if it is assumed in this model, in other models this code indicates that the level of the filled water is incorrectly determined.

F8 sequential wash mode does not work

F9 water filling system is not technically working properly

F0 the controller board may be faulty

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Flavia dishwasher error codes

E1. There is no water filling, since the filling valve may not have opened in time

E4 overflow occurred, check the tightness of the dishwasher

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Gorenje dishwasher error codes

E1. The sensor for leakage and the presence of water in the pan is triggered, if it is provided by the design of the dishwasher

E2 water overflow sensor triggered

E3 there is no water heating, the temperature sensor may be faulty

E4 breakdown of the temperature sensor, that is, there was a loss of contact

E5 there is no water supply, there may be no water in the central water main or the water pressure in it is very low

E6 the water drain is turned off or the drain hose may be blocked, and there is a possibility that the water drain pump is faulty or the waiting period has been exceeded

E9 is the same as error E2

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Hansa dishwasher error codes

Mode signal code Short program flashes E1. Water is drawn for too long, the water supply valve may be closed, blockage, low pressure

Eco mode signal code flashes E4. Water level or pressure too high

Indesit dishwasher error codes

Al01 The reason for this kind of error is the operation of the aquastop. Such an error will be accompanied by a body leak in the pallet area.

Al02. This error occurs when there are problems with the flow of water. The elimination of such an error should begin by checking the SV filler valve.

Al03- This error occurs as a result of water drainage problems occurring. A problem arises because the longest time for draining the water has been exceeded. This time is equal to 4 minutes. In this case, the sensor is in the full position. As a rule, with this error, the following problems arise: the pump for draining the water comes into a malfunctioning state, there are problems with the contact, the pump impeller is also blocked, the electron module malfunctions.

Al04- This is due to NTC temperature supply circuit problems. To eliminate the error, replace the electronic module.

Al05- This error is related to problems with the circulation pump. This problem is related to a sensor malfunction. With such an error, malfunctions such as a malfunction of the starting winding and the electron module occur. There is also no contact of the pump condenser, blockages occur in the filter tank.

Al06. The error is associated with a circuit power failure from the SV filler valve. With such a problem, a bay valve malfunction occurs, the level sensor is in a closed position.

Al07. This error is not used

Al08. An error resulting from problems with the NTC temperature sensor. This error occurs due to exceeding the permissible water heating time.

Al09. This error is related to software recognition issues. In this case, the keyboard is faulty.

Al10 this error is related to a malfunction of the heating element.

Al99. This error occurs as a result of problems with the cable and the electron module.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Kaiser dishwasher error codes

E 1 the time threshold for waiting for water supply is exceeded, therefore, the supply valve is turned off or the inlet hose of the dishwasher is disconnected

E 3 the time for heating the water in the tank has been increased, but the set temperature has not been reached, which signals a malfunction or breakdown of the temperature sensor in the heating element.

E 4 there was a water overflow, the filling sensor may not have worked

E 6.7 malfunction of the temperature sensor or a short circuit

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Kueppersbusch dishwasher error codes

1 flash end the dishwasher tank is not filled with water, the water tap is clogged or the waiting time set by the program has been exceeded.

1 flashing start no water, the water tap is closed or the dishwasher inlet hose is disconnected.

2 flashes end. The machine does not drain the water, the pumping out hose is not routed correctly, is bent or pinched.

3 flashes end flood protection activated

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Lg dishwasher error codes

Oe water does not drain out of the dishwasher

Ie. Water does not flow into the dishwasher

E1. Automatic draining of water from the machine chamber is working, possible water leakage from the hose connections

Fe water is being drained, but the water supply exceeds the permissible level, there may be a problem with the inlet valve

The water heating circuit is NOT damaged

Te the thermistor may malfunction, and therefore the supply water temperature is high

Le the dishwasher motor may be defective

Ce. There was a depressurization of the washing chamber or one of the technical units is leaking.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Miele dishwasher error codes

F01- the problem is related to the short circuit of the temperature sensor. When this error occurs, heating is turned off. Troubleshooting should start by checking the sensor and connectors.

F02 the temperature sensor is in open state. When such an error occurs, the heating is automatically turned off.

F11 The error indicates that water is not drained. The causes of the problem are: blockages occurring in the drain system, filter blockages, the drain pump becomes faulty.

F12 error indicates problems with water ingress into the car.

F13 error indicates that there is a problem in the heater pressure switch. As a result of an error, the program is interrupted and the pump starts to drain.

F14 error in the heater relay.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Neff dishwasher error codes

E1 error indicates that water is not heating. You can eliminate the cause of the error by checking and eliminating the problems of the heating element, thermostat, water sensor.

E2 error related to the level sensor. Water resistance should be approximately 50KΩ.

E3 water intake problem. Eliminated by checking and troubleshooting pump, inlet valve and NTC sensor.

E4 flow switch problems. The elimination of the problem should begin with an inspection of the sensor and its circuits.

E5- excess of the possible amount of water. The problem is caused by a malfunctioning valve or level sensor.

E6- aquasensor error.

E8. Insufficient amount of water in the pan. The error can be eliminated by increasing the water filling pressure.

E9 problems associated with heating elements.

E11. No heating.

E14 water flow sensor operation problems.

E15. Aquastop error.

E16 automatic water set.

E17 chamber filling sensor error.

E18. Automatic end of the program after draining the water.

E21 malfunction of the water pump.

E24. Problems associated with the draining process.

E27 low voltage.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Samsung dishwasher error codes

E1. Water supply time exceeded or limitation, low head.

It is necessary to check the presence of cold water and the pressure in the water supply.

E2. Drainage malfunction. The water is not completely drained, or an error has occurred in the operation of the water level sensor. Check if the drain is clogged with food debris, clean if necessary.

E3. Increasing the operating time of the heating elements, obtaining the optimal water temperature does not occur.

E4. Water leaking or overflow. Leakage of water, or excessive water supply. Probable cause of occurrence. Malfunction of the bay valve, or water level sensor.

E5. Weak water pressure. Insufficient water level in the dishwasher or faulty level sensor childbirth.

E6. Temperature sensor malfunction. Breakage or short circuit.

E7. Temperature sensor malfunction. Sensor malfunction or opening.

E8. Alternative valve operation error. The FLEX valve cannot be set to the desired position.

E9. Defective button operation. If the button is held for more than 30 seconds. Possible cause of the problem. Short circuit, or sinking of the button.

Ea. Violation of the water level sensor. Too much water in the dishwasher or a problem with the water pressure switch. Check the position of the drain hose, at the end of the washing cycle, clean the drain from food residues.

Uc. Voltage problems. The power supply is in the range of less than 180 V or more than 270 V. To avoid a short circuit or damage to the machine, it is recommended to reset the washing program and wait for a stable voltage in the mains.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Siemens dishwasher error codes

E1 Fault in water heating

E2 Fault in the heat sensor

E3 Difficulty in drawing water

E4 Defective flow change element

E6 Water sensor failure

E8 Not enough water

E9 Failure of heating element

E11 PMM works without a heating element

E14 Water flow control failure

E15 Water blocker activated

E16 Accidental filling with water

E17 Water supply failure

E21 Malfunction of the drain pump

E24 Failure in pumping water

E27 Insufficient supply voltage

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Smeg dishwasher error codes

E1. Failure of the acquastop system. Water leakage protection included.

E2. The water level limitation system in the dishwasher has been activated. Probable cause of occurrence. Problems with the drain or with the water level sensor.

E3. Heating system error. The permissible water heating time has been exceeded. E4. Failure of the water temperature sensor. Short circuit or open circuit in the circuit.

E5. Violation of the filling process with water. Water is not filling or is filling incorrectly. Possible reasons: low head or lack of cold water, faulty bay valve.

E6. An error occurred while draining the water. Water does not drain or does not drain properly.

Check if the drain hose is positioned correctly, it may be pinched.

E7. Turbine defect (if this equipment is present in your model). Measurement of the amount of water poured is inaccurate.

E8. Malfunctions of the alternating wash system.

E9. The dishwasher filling system is defective. Check for cold water and pressure.

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Vestel dishwasher error codes

E1 error in the operation of the water supply system, it is necessary to find out whether the supply from the central line is open and whether the inlet hose is connected

E2 malfunction of the water supply cycle, filling occurs constantly, it is necessary to close the supply valve until the malfunction is eliminated

E3 water drain mode does not function properly

E4 malfunction of the temperature sensor or heating element of the machine, as a result of which the system reports that the required level of water temperature is not reached

E5, the system reports that water is overflowing, and it is required to shut off the supply and turn off the machine until the malfunction is eliminated

E6 system board failure

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Whirpool dishwasher error codes

E LED flashing, F flashing

1-5 E1 The water stop sensor is activated, it is necessary to find out if everything is in order with the drain hose, check its integrity

2-5 E2 There is a security threat

1-2-5 E3 Failure during heating, the water temperature sensor may be out of order

3-5 E4 there is no communication between the system and the heat sensor of the dishwasher

1-3-5 E5 Difficulty filling water

2-3-5 E6 Disturbance in water discharge

10 F0 Sensor out of order

1 F1 Failed NTC controller

2 F2 Depressurization

3 F3 Failure in water heating

4 F4 Water not drained

5 F5 Water supply cut off

7 F7 Water flow control failure

8 F8 Small amount of water

9 F9 Continuous water supply

11 FA OWI water sensor failure

13 FC Water hardness sensor failure

8 (495) 565-38-25 and 8 (499) 409-84-95 feedback form

Zanussi dishwasher error codes

Indicator signal END, 2Hz, / 5sec pause

1 blinking i10 no filling process or the inlet hose of the dishwasher is blocked, you need to check the connections or find out if there are any kinks

2 flashes i20 the water does not drain or the drain pump is faulty, the drain hose may be disconnected and the aquastop program is activated

3 flashes i30 Dishwasher overfill protection activated

5 blinks i50 error in the operation of the circulating pump triac, it may be faulty due to a short circuit

6 blinks i60 error in the operation of the temperature sensor or a failure in the operation of the water heating system

7 flashes i70 there was an interruption in communication with the NTC sensor or a short circuit in the circuit

8 flashes i80 signal loss, no contact with external memory, which is accompanied by a coded EEPROM message

9 flashes i90 checksum error of encoded information from MCF or CCF

10 flashes iA0 Water supply cut off

11 flashes ib0 transparency sensor failure

12 blinks iС0 communication error with user display

13 flashes iАd0 error or temporary disconnection with the tachogenerator, but the pump continues to work

14 flashes iF0 Water filling timer failure

Drain filter clogged

It is possible to establish in what condition the drain filter is possible only when inspecting it. It can be accessed from the front of the washing machine at the bottom. Usually on the right.

Since access to the filter and its cleaning is accompanied by the flow of a small amount of water, it is necessary to prepare for cleaning in advance:

  • Put a rag on the floor;
  • Put a jar or other container nearby, into which it will be possible to direct the water flow.

Filter cleaning procedure:

Open the hatch.

  • By turning the plug counterclockwise, pull out the filter.
  • Drain the water into a rag or jar.
  • Clean filter by removing debris.
  • Rinse the filter.
  • Put it in place.
  • Close the hatch.

Even if the filter is not clogged with debris, cleaning it will benefit the machine.