Connecting the IP Camera to a Computer

Cloud video surveillance from a webcam and router

If you want to install video surveillance system in your home, but after examining the of cameras and DVRs, the idea disappears, then let’s consider a budget option using the webcam and router.

Get a simple video surveillance system with motion detection and cloud storage that requires no computer, DVR and white IP address turned on. Available features:

  • Motion detection in the specified areas with the recording of 2 frames per second
  • frame saving at a set time interval
  • Archive storage on a USB-flash drive
  • Archive recording to the cloud (optional)

What you can use such a system for:

  • Surveillance in the apartment, house, cottage
  • Babysitting
  • Supervision of pets
  • Control over the employees in the office
  • Visual control of equipment (heaters, gas appliances, etc.).)
connecting, camera, computer

What are the advantages of IP video surveillance?

Below we will mainly touch on issues specific to the choice of video surveillance, i.e.е. Assuming that the right choice between analog and IP is already made.

Router settings

To successfully configure the router we need to:

connecting, camera, computer
  • Connect all configured cameras to the router via network LAN ports or via Wi-Fi.
  • Connecting the device to a PC with a network cable.
  • Go into the router’s web interface, where we will work on port forwarding, so that the router will distinguish them and the cameras accordingly, giving in response to a request to him the desired image.

The lines that need to be filled out can usually be found in the “Virtual Server” tab. Before filling in all sub-items, check the box “Enable virtual server?”Yes” in the “Yes (Yes)” field. Further settings depend on the router model and may include the following items:

  • “Service name”. any value, for example, “Camera1”;
  • “Port range”. must correspond to the port that was previously assigned to the first video recording device;
  • “Local IP address”. corresponds to the address of the camera;
  • “Local Port”. insert here the value from the second item or 80 if manual port setting is not available for your camera;
  • “Protocol”. make sure to specify TCP in this field, as this is the protocol with which IP-cameras work;
  • “Protocol number” You can write any number.

These items shall be written manually for each camera, remembering to change the values in the appropriate lines.

Connecting the IP camera to a Wi-Fi network using a computer

Let’s configure the Wi-Fi and camera. To do this:

  • Install the utility that comes with the original device, or download the software from the Internet (for example. the program “VSTARCAM” for the appropriate brand of cameras).
  • Connect the IP camera to the router, using the RJ-45 cable.
  • Open the previously installed program by double-clicking and go to the camera settings.
  • Select the “Signal search” and in the list that opens find the router and click “Install”.
  • Enter the router password to access the Wi-Fi network, click “OK”.
  • An error window may appear, but do not worry. To solve the problem, do a second search, check the status of the network cable, its connection to the camera and router.
  • If the settings are correct, the camera will reboot, then you can disconnect the cable and the IP camera will work wirelessly.

Setting up Wi-Fi via mobile device

Setting can be performed from any smartphone (operating system does not matter) or tablet. To do this:

  • Repeat the first 4 points from the previous list.
  • Installing the app on your mobile device. CSCAM, EYE
  • Open the utility, go to Camera Settings.
  • Go to “Wi-Fi settings” and select the network we want.
  • Enter router password to access the network.
See also  How to print on a printer from a Windows computer


On July 16, 2020, we at Intems launched a monthly draw for one set of video surveillance for 29,733 rubles. Since then, we have been raffling off one CCTV kit every month. To learn more about the raffle kit, watch this video, detailed conditions of the raffle in the description to this video.

This is our little attempt to make this world a safer place, as scientific research confirms. that video surveillance prevents crime, and a little bit fairer because video surveillance really helps investigate crimes. It’s especially important for those, who for some reasons can’t afford to buy it. After all, it is people with low income who are more likely to become victims of criminals. If you like our idea, it’s very easy to support us, be sure to read this article. 7 the most common ways of “cheating”, which you will encounter when buying video surveillance. And of course if possible, share this information with your friends on social networks.

How to connect an ip camera to your computer

Switching to IP-cameras is easy to implement, if you know the technology to properly connect and configure. This is quite a challenge for the novice user of PC, but for someone who owns a computer, to connect the ip-camera to the router is not difficult.

Choosing a camera

What IP camcorder to choose? For your purposes, we choose video devices with high-tech matrix:

Determining the address

Before you connect IP-camera to the router, you need to find out the own address of the device. Usually it is not difficult, because the camera comes with a special program that allows you to determine the address. If necessary, the same software can be found on the manufacturer’s official website. Sometimes the address is written in the manual or on the box to the device.

Finding out the IP address of the local network

Find “Network and Sharing Center” on your computer, select “Connection”, click on “Network”, then go to the “Information” page. Now we need to find the line “IPv4 Address” and in front of it are the numbers we need. Copy it to a separate file.

Change the IP address and create a subnet

Before we can connect the IP camera, we need to change the IP address. You can do it with the same program which helped us to find out the value of IP-address. Or you can change the local network IP address. Our job is to make sure that the camera and computer are on the same subnet.

For example, the camera address is and the local network address is The subnets here are displayed in the numbers 1 and 88. Our task is to change these values to be the same.

Find “Network and Sharing Center” in the computer, select “Connection”, click on “Network”, go to the Network and Sharing Center, select “Connection” “Network” “Wireless Network Properties”. Under “Default Gateway” you will find the “Internet Protocol version 4 (TCP/IPv4)”, click on it, open “Properties” and check the box “Use the following IP address”.

We have three lines where you need to write:

  • IP address of our local network20.1.44, previously changing the subnet number (from 88 to 1);
  • Under “Default Gateway”. The full value of the camera address.

Save the changes. Now you need to open any browser and enter the full IP address of the camera in the search box. You will see a form, where you must enter your login and password. You can find this information in the instruction manual or on the camera-recorder box. After entering entered data, you get access to the recordings and camera settings.

connecting, camera, computer
  • Install and configure DVR software on the PC.
  • Set up password and user name.
  • In the “Settings” area you can enter the information you would like to provide by clicking on “Add zone”.
  • After opening the window, the “Find device” function is clicked.
  • The program automatically searches and displays a list of connected devices.
  • Then if necessary, you specify the name of the camera through the “Add device” tab.
  • To display a camera picture on the screen, the corresponding device is selected and the “View” function is pressed.
  • The mode of operation of the equipment is set in the “Settings” area.
See also  How to remove iPhone emoticons on Xiaomi

Cloud surveillance from operators

Operators are companies that do not produce video surveillance equipment. They order equipment under their brand (OEM) and develop software that allows remote viewing of live video and archive. For example, Ivideon is trying to sell their OEM junk plus their cloud hosting for a monthly fee. But if you dig around on the site you’ll easily find the software Ivideon Server and Client, which can be used to connect almost any camera and view them over the Internet, but to do this you will need to sit on the needle of subscription fees. The software has to be installed on the computer, which in itself is a bad idea because your computer will then run 24 hours a day. Which will lead to its increased wear and tear, especially if you’re going to write a video archive on this computer.

  • Allows remote access even with “gray” IP addresses.
  • Allows access to live video viewing and video archive on a computer.
  • Monthly subscription fee.
  • 24 hours a day computer.
  • Computer resource consumption for video processing.
  • Poor cybersecurity, and the worst thing is that if hackers break into such a reverse service, they will get everything at once, here recently one “star” of cloud surveillance was broken and got access to 150 thousand. CCTV cameras.
  • Dependence on cloud operability

Verify IP cameras in the facility

The result of a fully debugged IP video surveillance system is considered:

  • Maximum picture quality from all IP-cameras at the facility without freezing or interruption of the image;
  • clear and well-thought-out organization of video recordings from all IP cameras and their quick review if necessary.

For example, the already known recorder from PRS will display the video streams from all IP cameras on the monitor screen.

The result. control of all surveillance areas at the facility

What to do if there’s no image from IP cameras

  • Not only is there no video stream but CCTV software doesn’t even show up with an empty image grid. Whether the monitor is on, whether it’s in working condition. Check if the cable is not damaged. if you have a spare one (spare from the kit or specially bought), plug it in and check if the monitor works with it. Check if the DVR, PC or server room rack (if it’s the server station where the drive is located) is on or off.
  • The video recorder and monitor are turned on and working, but the screen shows a blank grid of video streams. Check whether all IP cameras have power supply; it doesn’t matter if it’s common for all cameras or if IP cameras are powered by independent power supplies. Bypass all power supplies, if they are located in different places of the object. each of them as close as possible to its IP camera. UPS turned on (if backed up power is used for IP cameras themselves).
  • The video grid is full, but there is no video from one or more cameras. Check the problem IP cameras. from power supply to finding and fixing a break (or accidental disconnection) of the corresponding LAN cables. In rare cases, the IP camera itself may be damaged: extreme temperature fluctuations that caused its wear and tear, damage of IP cameras installed at night on the front gate or in other places visible from outside. It is not necessary to penetrate to the object. on IP camera intruders can shoot through the lens (the weakest point, even if the IP camera is vandal-proof). In master shooting with telescopic sight can be damaged not only the IP camera itself, but also cut cables, shot off mount (especially when all is made of aluminum), shot through the IP camera body in any place. You should not forget about it either, when placing video cameras outside.
See also  HP notebook does not turn on black screen

No power on IP-cameras 1-3 out of 4 connected to IVR recorder

The last point requires explanation. Disk failure is associated with the appearance of Bad sectors (“bad” sectors on the disk space), which “cure” is not possible in large numbers. Every drive has a small spare area with some thousands of “damaged” sectors to replace “bad” ones during re-mapping procedure (“remapping”) automatically or with special software (HDD Scan/Regenerator, Victoria and their analogs). In the second case you need to remove the drive from the DVR or the server rack and then connect it to any PC and check with the same Victoria (there are MS-DOS and Windows versions).

Bad Blocks are growing fast which means you have to throw the drive away

Up to several hundred incorrect shutdowns can throw a multi-terabyte disk. worth many tens of thousands. in the trash. Even if Bad blocks were in one place and the drive had to be software cut. in the old requirements of your CCTV system it will not fit anymore, and the drive is simply replaced. That is why it is recommended to power IP-cameras with a powerful UPS (especially if each IP-camera has an SD-card, so that frequent shutdowns do not “kill” all memory cards in IP-cameras). and use a laptop, netbook or smartphone with Windows Vista/7/8/8 instead of a recorder.1/10, which is configured to automatically shut down (or hibernate) the system when the batteries are low due to a sudden power outage overnight. And a notebook should have a decent amount of power and speed to spare.

The above instructions show what to look for when debugging an IP video system. This allows you to take your object under reliable protection from unwanted guests. And if something does happen. with 100% probability the culprits of the incident can be identified the very next morning when you come to work.

Access via Internet

To access the camera via a wide area network, you will need to configure the router itself. First of all the router should understand what address corresponds to each device. Only then will it be able to send the correct image to the screen. The Virtual Server tab contains the necessary parameters, where you can enter the data for each device. This is not only the original IP-address, but also ports, if any.

The advantage of this method is that it allows you to monitor the surveillance network from anywhere in the world. To connect just use any device with Internet access. Cameras must be assigned a static name provided by private providers free of charge or for a fee.

Before you start using the devices, check their operability. To do this you need to open your browser and put the original IP address into the address bar. For local networks with only LAN cable this will be enough.

In the case of access via the Internet, the request looks like this: “://”, or “://static_IP_address:8081”. If the cameras are set up correctly, the screen will display data from them. The same method is used later to control the network.

Denial of responsibility | Contacts |RSS | SE | EN | BR | DE