Asus Rt N12e Repeater Setup

This step-by-step instruction is devoted to how to configure the Asus RT-N12 Wi-Fi router to work with providers:

The manual will include the following important configuration steps: the correct connection of the router, how to enter the Asus RT-N12 settings, setting up an Internet connection, setting up wireless network security (Wi-Fi password).

How to connect Asus RT-N12

Despite the fact that this seems obvious, I start all the instructions exactly with how to connect the router correctly, because even here there are errors, due to which subsequently the Wi-Fi connection does not work.

There are five ports on the back of your router — four LAN ports and one WAN (Internet) port. It is to the latter, which differs from the other four ports, you should connect the cable of your Internet provider. Beeline, Rostelecom or any other.

In addition, I recommend that you configure the wireless router from a computer or laptop that has a wired connection with it, for which you should connect one of the LAN ports on the router to the same port on the PC network card.

And the last point: it is advisable to check the connection settings in Windows (how to do it). you can skip this step now, but if you can’t get into the settings of the router, go back to it first.

Remember to plug the device into a power outlet. And also, for all subsequent steps, turn off the Internet on the computer (if you have “High-speed connection” and “Beeline” running on the PC itself) only the local area network connection should be active.

How to enter router settings

On the back of the Asus RT-N12 (as on other routers) there is information about the address, login (username) and password. they must be used to enter the settings web interface. In order to log in, launch a browser and enter the specified address in the address bar, for Asus routers it is 192.168.1.1.

When you are asked to enter your username and password, enter admin for this and for the other (provided that you did not change them during previous attempts to configure everything).

Now attention: if this is the first time you have come here after purchase or if you have just reset the router, automatic configuration will begin. you will need to click “Next” and fill in the proposed fields.

Asus Rt N12e Repeater Setup

Automatic router setup

You will be prompted to change the password to log into the “admin panel” of the router (the one that was admin), after which an attempt will be made to determine the type of connection and, if it is determined, you will be prompted to enter a login and password on the Internet, and then set the Wi- Fi network and password on Wi-Fi.

I will not describe automatic setup. If it succeeds (and this may be so for Rostelecom and Dom.ru), then you do not need my instructions. as a result, you will be taken to the main page of the manual settings Asus RT-N12, and the Internet will work. If after that the Internet did not work, then I will tell you how to configure everything manually.

Beeline connection setup

In order to configure Beeline Internet on Asus RT-N12, on the main settings page, click “Internet” on the left, and on the page that opens, fill in your connection settings as follows:

  • WAN Connection Type. L2TP
  • Get IP Address Automatically. Yes
  • Connect to DNS Server Automatically. Yes
  • Username. your Beeline login
  • VPN server. tp.internet.beeline.ru

And save the settings. If you entered everything correctly, and the Beeline connection on the computer is disconnected (this is necessary), after half a minute the router will establish an Internet connection and in a separate browser tab you can open any sites, and Wi-Fi-connected phones, tablets and laptops will also have access to the internet.

You can proceed to setting up a wireless Wi-Fi network if you want to change something in its settings (later in this manual).

Connection setup Rostelecom, Dom.ru (PPPoE)

To configure Internet Rostelecom or Dom.ru on this router, click “Internet” in the menu on the left, then fill in the proposed fields as follows:

  • WAN Connection Type. PPPoE
  • Get IP Address Automatically. Yes
  • Connect to DNS Server Automatically. Yes
  • Username. your login Rostelecom or Dom.ru (for the Internet)
  • Password is your password for the Internet.

The remaining parameters do not need to be changed. Save the settings and, if everything was done correctly, then after a short time the Internet will be connected to the router, and you can open the site and everything else from this computer, as well as from other devices connected to the router (in this case, the High-speed connection on the computer should be disconnected )

If required, also configure the wireless network settings. its name and password.

Configure Wi-Fi wireless settings

To configure Wi-Fi, select “Wireless Network” in the menu on the left, and then set the necessary parameters:

  • The SSID is the name of the wireless network that you and others will see, so that you know which network you are connecting to. Do not use Russian letters.
  • Authentication Method. Install WPA2-Personal
  • WPA pre-shared key. this is the password for Wi-Fi. You should not use the Cyrillic alphabet, should consist of at least 8 characters.

Save the settings. If you were connected to the AsusRT-N12 wirelessly, then when you change the settings, the connection will be disconnected and you will have to reconnect to the wireless network. At the same time, Windows may report that it is not possible to connect to the network, in this case we proceed as described in the article Network settings stored on the computer do not meet the requirements of this network.